开云体育

Yep same here Ron. I didn't try to investigate, just reverted to 2.2.12.04 which then worked fine. My setup is a little unusual in that I modem sync in both directions, which had some PTT/timing/mode

I handled a radiogram containing an ARL SEVENTY component and found that the ARL messages in FLDigi didn't go that high. Did some searching and found that NTS 2.0 defines a number of additional

Wondering if anyone else is seeing a problem with Flamp version 2.2.13. I am using Linux Mint. On a net tonight I pressed XMIT and nothing happened. I was able to report missing blocks on a received

http://www.w1hkj.com/files/flamp/ * Amp-2.V3.0.Protocol.pdf <http://www.w1hkj.com/files/flamp/Amp-2.V3.0.Protocol.pdf> * Amp-2.V3.0.Specification.html

* * *?????????????? Sound Card Digital Modes (for Rookies)* * * *Class TODAY (Saturday July 6)? at? 10 AM? EDT by Zoom* *Zoom link:*

at http://www.w1hkj.com/alpha/flrig/ * darkscheme.UI.prefs <http://www.w1hkj.com/alpha/flrig/darkscheme.UI.prefs> * flrig-2.0.05.66.tar.gz <http://www.w1hkj.com/alpha/flrig/flrig-2.0.05.66.tar.gz> *

Hi It appears that I've lost the power meter on this version. SWR and ALC work fine 73's Ian N0IMH

If using the Signalnk, use the 6 pin mini-din connection, assign the channel to external data, and use VOX for FLDIGI. For FLDIGI with Signal link I use a fairly long delay so it doesn’t chatter.

Hello. Can anyone please advise how to set up in FLDIGI CAT/PTT for the Kenwood TM-V71, SignaLink USB and WIN11? ?I am not sure which of the six FLDIGI Config-Rig Control options to use and what the

at http://www.w1hkj.com/alpha/flrig/ Index of /alpha/flrig * Parent Directory <http://www.w1hkj.com/alpha/> * darkscheme.UI.prefs <http://www.w1hkj.com/alpha/flrig/darkscheme.UI.prefs> *

9 times out of 10 it is low grade close in rather than hi grade far away. Turn circuit breakers off one at a time. Sounds like it might be a UPS since you have harmonics which are notorious.

Hi John, I'm on 1.5.? I'll update and report back. Thank you! -- Roy Dugger, KD6R

Hello Roy, Could you please check if you are running the latest version (1.6.0.7). It can be downloaded at: https://bitbucket.org/VK2ETA/andflmsg/downloads/ If yes, can you please confirm the issue is

I tried on my Galaxy S23 , Android 14. I get error message that application is not compatible with latest Android version and is missing security requirements. I can open the NBEMS files folder and

*Here is my "noise level" revealed by the RSP play SDR (hardware) and RSP spectrum analyzer (software)* *The vertical scale is in dB? (from -100 to -30 dB).? I can't remember where the S-units

Hello Rob, No problems. I just tried it on my Android 13 phone and the list if app presented for sharing when i select "For printing" and HTML is quite limited compared to what used to be there. I

John, Might you have suggestions on how to print forms from AndFlmsg? The printing app on my phone does not seem to recognize the files I can export using the AndFlmsg "share" button. Thanks for all

Here is a n excellent demonstration of the ability to send text via an unmodified analog shortwave broadcast transmitter. PSKR125C10 (1100 wpm) is centered on 2250 Hz, while simultaneous MFSK64 (240

http://www.w1hkj.com/alpha/flrig/ Index of /alpha/flrig * Parent Directory <http://www.w1hkj.com/alpha/> * darkscheme.UI.prefs <http://www.w1hkj.com/alpha/flrig/darkscheme.UI.prefs> *

http://www.w1hkj.com/alpha/flamp/ Index of /alpha/flamp * Parent Directory <http://www.w1hkj.com/alpha/> * flamp-2.2.12.04.tar.gz <http://www.w1hkj.com/alpha/flamp/flamp-2.2.12.04.tar.gz> *