开云体育

GIN & PEZ@arg; New results to please you all the more. I just replaced your mini equation: https://www.op4.eu/code/G-mini.c.gza.cc.by.4.0.2019.png with your even smaller equation as presented in Part

I'm using a Dell laptop at 1366x768, font size 8, 16:9 aspect ratio, Windows 10. I haven't had problems with the scrollbars being present or overlaying the taskbar since before nanovna-saver version

GIN & PEZ@arg; Excellent news to hear. Have you done any recent IEEE publication or presentations of the work you are presenting here, or have plans for presenting at any Conferences? -- 73 Gary, N3GO

Sam, Have a look at Classic Shell for your windows OS. It makes the start menus look like win7 and works quite well with the current win10 update.? ... Larry On Sun, 3 Nov 2019 at 4:41 PM, Rune

Hi Ady, That is why for version 2 hardware, folks are asking for Bluetooth or wifi control of the unit.? ... Larry On Sun, 3 Nov 2019 at 3:48 PM, Ady, YO2NAA<yo2naa@...> wrote: Hi all,

Hi Sam, I think maybe the Windows 10 task bar is a few pixels more than the Windows 7 one? I'll try to see if I can find a few pixels in the interface so it will fit - it should be possible :-) It

#71: Good News : (1) DEP was Restored and Maxima is still Working in these 2 cases : [WXP64P&SP2] and [W7P64], (2) Maxima Worked Immediately in [W8.1P64] @Oristo - 2 November 2019 :

Hello again Rune, Once I figured out how to hide the taskbar (face palm!) it fits. It would be nice of it would fit without hiding the taskbar though. 73, Sam Reaves ARS W3OHM Owner and Moderator of:

Hi Rune, I am using Windows 10 on a HP15 f162dX 15" screen 16:9 aspect ratio laptop. Data is here: https://support.hp.com/us-en/document/c04530928 I like is because it's a Intel I3 is lightweight and

The calibration routines start at line 1034 https://github.com/ttrftech/NanoVNA/blob/master/main.c -- Erik, PD0EK

Got bitten too it seems. Hopefully I can get a refund via Mastercard. I think this may be protected. As for the scammer, pillory.

I was fortunate enough to get some high-quality PTFE (Teflon) coax (RG-174 sized) SMA to BNC jumpers - and these hold up much better, probably because they have a small piece of heat-shrinkable tubing

This is how I am driving the Mag loop

Hello, I am looking for any references that explain the formulas used by the NanoVNA to do calibration and measurement corrections. I have looked at various six- and twelve- parameter corrections.

Hi I used the following approach with my mag loops. Capacitor is driven by a stepper motor controlled remotely (Arduino + Nrf24l01 module) When I decide to have a QSO session, I first run a

Hi all, regarding saving the scan and download it later, I think a nice firmware feature would be to schedule a delayed scan followed by a pause after the scan. This will allow to hang the NanoVNA to

Check out the ModularTuner http://www.github.com/profdc9/ModularTuner This is an automatic antenna tuner with a directional coupler that you could program to search for the minimum SWR. It can be

As a first step I will model the reference Z0 ( normally 50 ohm ) as a RLC combination If that is not enough I will add some unbalance to the moebius transform. -- Erik, PD0EK

Ian, try: python -m pip install --user --upgrade pip and next PyQT5 install I hope help Gyula, HA3HZ

Hi Oristo When the cal kit calibration kit is loaded in the VNWA software you simply open a custom trace and in the Expression line write s_load or s_open or s_short or s_thrumatch or s_thru then the