开云体育

Here is a picture when running a stylus all over the screen in a touch test

My nanoVNA arrived in Dec and functions just fine in RF terms. The touch screen has never been correct and the numerical input from the pad has not worked. It is: ch> info Kernel: 4.0.0 Compiler: GCC

Rune, Thanks for fixing the "Offset Delay" bug in Calibration. I checked it out with several coax cables and got good results. It also correlates with the "electrical delay" parameter in the NanoVNA

On Sat, Jan 11, 2020 at 03:47 PM, Leif M wrote: Is S11 or CH0 impedance also available in polar plot form? ======================================================== Leif, You may have already found

When I reloaded my Linux Mint XFCE 19.2 because of screen freezing up I installed Mint XFCE 19.3 and after a reboot it decided that I should not have administration rights over any USB drives. So I

On Sun, Jan 12, 2020 at 01:51 PM, Joe Kirk wrote: I have one of the white NanoVNAs but the high level menu does not have the Config option which I understand would show me the current version of

If you are updating your previously installed NanoVNA-Saver in Linux, the procedure is the same with one exception. If you try to do the gitclone, it will complain that the directory is not empty. So

I have one of the white NanoVNAs but the high level menu does not have the Config option which I understand would show me the current version of firmware. How can I find out which version I have? TIA

You can get much better than 20Hz by watching S meter, when you are very close it will swing due to constructive and destructive action on the signal. Get the S meter to nearly stop swinging and you

On Sun, Jan 12, 2020 at 12:38 PM, Roger Need wrote: " … The latest version has fixed the (offset delay) bug. I just made a number of tests using NanoVNA saver 2.2 with different length cables and

Herb, That's great information that you shared. Thanks!

If you can't install nanovna saver, I recommend nanovnaPartner, which works under XP. You can find the latest version of nanoVNA Partner v0.19 on my website (ha3hz.hu) 73, Gyula HA3HZ

It is likely that the nanovna-saver will work from python under XP. However, Python 3.5 and above will not work on Windows XP. Try 3.4.4 and if you succeed in installing Qt5 then you are close to

Hi Chuck, i see you need to install a driver on windows 7 so that your computer can see nanoVNA. To do this, download and install en.stsw-stm32080.zip (DfuSe) or STSW-LINK004 (ST-Link) or

I agree. It takes extreme cases like that short Double Zepp , to show that in an otherwise tuned system the feedpoint SWR really makes that much difference. In this case some 8 dB are hidden behind

Herb, Thanks for the correction to my previous post. You were right! The latest version has fixed the bug. I just made a number of tests using NanoVNA saver 2.2 with different length cables and got

On Sun, Jan 12, 2020 at 11:58 AM, Pete Buxton wrote: " ...I was excited when I found that it connected on serial port using PuTTY, but can't find any info (other than the help command) how to control

Not only can our ears not detect much below 30 Hz, our radios don't do too well with that frequency and below, either. Most cut off 'around' 100 Hz. For those who must split hairs on frequency

Thank you, Herb, With your advice, I will try the nanovna-saver on Windows but thought I'd try the Web app just for kicks. I wasn't aware of the Web app until I saw your mention of it in this post.

I am not a fan of the Si5351. It was intended to be used for digital clock generation for processors and peripherals, not for RF signal generation where reasonable signal quality is needed. Its only