开云体育

On Wed, Mar 9, 2022 at 10:49 PM, Colin Coker wrote: "Thinking about upgrading my very early NanoVNA to a 4" screen version. What is the difference between the H4 and V2? Which one should I go for. "

the translator not work on English *Sent:* Thursday, March 10, 2022 at 4:42 PM *From:* "Costin R" <electronice.az@...> *To:* [email protected] *Subject:* Re: [nanovna-users] Nanovna-H

Yes,go for the LiteVNA 64 is good, I use? the price is ceep and the firmware is the best. *Sent:* Thursday, March 10, 2022 at 12:51 PM *From:* "Larry Rothman" <nlroth@...> *To:*

Confirm. That translator is not working. I tried several times. I use Chrome where with a right click I have access to the browser's built-in translator. 73! Costin, YO8RCD

Hi Rudy. I own a H4-clone (hardware version 4.2.1). It came with the soldering pads free and no Transflash connector soldered on it. I provided for by myself. The RTC quartz was missing too and I

On Thu, Mar 10, 2022 at 05:53 AM, Jim Lux wrote: 1. "Is there a schematic published?" The LiteVNA is not open source so hugen has not released a full schematic. This is not intended to impede users,

The language selection feature doesn't seem to work on Safari, Chrome, or Firefox (MacOS Big Sur) - I think that something is not causing the translation to work, or it to re-render - If one selects a

Is there a schematic published? One issue with some of the later variants on the original NanoVNA is that they are *much* more sensitive to ESD (because they use RF switches on the inputs).? The

Gyula, I selected the English language from the list, but it did not cause the page to translate. As I said I tried 3 different browsers. I'm using MacOS and not Windows so maybe that is the issue.

Go for the LiteVNA 64 as it is the current design with the most active software development at this time and exceeds 6GHz. Manufacturer's website:

That firmware was created 2 years ago by forum member REALD. There was only a few releases and the H4 had not been released at that point in time. The last release of that firmware was Dec 2019. If

Hi Gyula, Yes, I am using Windows 10. Are you saying that Windows 10 updates disassemble the DfeSeDemo driver?? Does 'disassemble' mean 'make the driver non-functional'?? And are you saying that

Hi Ian, I assume you are using Windows 10 where in my reading, the updates cause an error to disassemble the driver that has previously been installed. Therefore, enter the DFUSE V3.0.6 directory

In any operating system browser, you will find a menu in the upper left corner where you can set the language. Otherwise, the page uses google translate. I'm sorry if you didn't figure out how to set

I am very happy with my H4, and would definitely get it, unless your primary use case is at frequencies in the GHz range. The V2 plus4 has a purportedly better design for the highest frequencies, and

If you use an android device there is a menu drop down on the top left of the page to select language. Garry M0MGP

Thinking about upgrading my very early NanoVNA to a 4" screen version. What is the difference between the H4 and V2? Which one should I go for. Thanks. Regards Colin -- This email has been checked for

Thanks Gyula, H for Hugen and D for DiSlord .... simple ..... :) I have connected my nanoVNA to the nanoVNA-App and it is recognized on COM3 etc.. However, when I then put the nanoVNA into DFU mode

Unfortunately not here. Tried 3 different browsers. 73, Cliff, AE5ZA

On mine a flag popped up at the bottom of the page asking to convert to English.