开云体育

Indeed, the HP16092A is the butt end of an APC-7 connector, with just 3mm of the centre conductor protruding beyond the insulator. It has an advertised max freq of 500 MHz. I agree with Dave that a

Hi Dave, 1- I've upload the Kicad project as a zip file. 2- I also upload a PDF showing this part of the schematic and layout with different zoom levels in case you can't download or open the Kicad

Howard, I used the SMA to SMA jumper cables which came with the Nano VNA and calibrated using the open, short and load connectors ( https://youtu.be/qb38VI-9tV0). Then I used an SMA to SO239 adapter

Well, simply put: First, do an OSL calibration for the range you want to use, and store it in one of the memories. Then select Display > S11 > SWR. It should then display the SWR of whatever is

"NanoVNAs Explained" by Mike Richards G4WNC is the goto book you need, available from a number of Internet shops. 73 DE G4SDW Gareth

Welcome to the group! The archives of this group contain much good information including videos and a guide for the VNAs for DUMMIES. Those resources should get you going. Dave -

Hey guys just got a nano VNA. it is a "seesii, nano VNA-H. I need some help in setting it up to see the SWR on some antennas. I have gone through the various manuals and the one that came with it,

1- Would you recommend to clean all 3 elements of the matching network, as I don't know which component will go where ? Can you send me a schematic of the matching network? Possibly I can figure it

Dave, Thanks for the hint. 1- Would you recommend to clean all 3 elements of the matching network, as I don't know which component will go where ? 2- If you look at the trace between the

Yes. The TINYSA is highly useful for frequency domain measurements. As well, the NANOVNA is equally useful for impedance domain measurements. As well, an o'scope is equally useful for time and

The calibrated signal generator output on the TinySA Ultra is a great tool to calibrate or check your S meter and also very useful for determining and/or checking your receivers sensitivity. It also

Hi James , the nanovna H H4 and LiteVNA64 , whith the recent FW has the TDR function but named TRANSFORM . You can reach the relative menu , tapping the DISPLAY >> TRANSFORM >> TRANSFORM ON. In the

They are completely different instruments, used for completely different purposes.The NanoVNA is a vector network analyzer. It can be used to measure resistors, capacitors, inductors, transmission

Hi As a hamradio operator what can i do better with TinySA ultra then NanoVNA H4 ? What kind of measurement with TinySA can be really usefull for antenna, filtering .. around hamradio activity ,

The NanoVNA-F-V2 has a convenient TDR function: It has its own menu choice. Just requires settings dependent on cable speed factor and short/long cable. Quite intuitive. Firmware 0.5.4 handles

Yes. When I commented "clean" the copper from beneath the inductors, I imply no copper beneath the component(s). Yes, that will introduce a slight impedance bump in the line. However, even a bit of

I know the NanoVNA H4 has a TDR function because I've used it. It isn't called that in the menu and is a little tricky to figure out. There is a Youtube'video that describes its setup. Also message

Haven’t bought one yet but I’d like to make sure I get a version capable of the TDR addition. I’ll have to figure out how to add it if necessary after receiving it. Thanks.

Stan and Thomas.. Thank you! The menu is very helpful! Got a whole lot of learning to do, i'll be fun! -- William, k6whp -------------------- "Cheer up, things could get worse. So I cheered up

Dave, That's very interesting. That is what I came across the datasheet of the capacitors I bought. Look at the picture, I think that's what you're talking about. Unfortunately, it is not mentioned