开云体育

Thank you all! I ended up grabbing one like this from the uber-large US seller: [image: image.png] (I don't like to advertise, so snip above) I initially wrongly got RG400 cables thinking they'd be as

Save yourself the grief and buy them with SMA already installed. There are a few US manufacturers over on that auction site that make them up in various lengths. 73, Dick, W1KSZ

Look on wish.com. I picked up some from them and quite happy with it. Just search for rf coax wrote:

Use DISPLAY->FORMAT .... ->SMITH (need select it) and on next click SMITH need select value format

Hi, I just upgraded to the newest version. It's DiSlord's 1.2.14. I recognized, that the smith chart marker now displays the impedanze (R +/-jX) and not the value of C or L in pF or nH. Is there a

RG316 50 ohm coax *Clyde K. Spencer* wrote:

You can buy ready-made SMA cables from Amazon and AliExpress (or similar). For example: https://www.amazon.co.uk/BOOBRIE-Coaxial-Connector-Pigtail-Emissions/dp/B09MRXCYKR There are PTFE variants:

https://www.aliexpress.com/item/32726071013.html?spm=a2g0o.order_list.0.0.62c51802ZQqmOB ?n joi, 22 sept. 2022 la 03:43, Radu Bogdan Dicher <vondicher@...> a scris:

I believe it's RG 316/u Bob VE3AMW ________________________________ Sent: September 21, 8:42 PM To: [email protected] <[email protected]> Subject: [nanovna-users] SMA coax cables the kit

Looks a lot like RG-316/U https://www.amazon.com/Eightwood-RG316-Coaxial-Coax-Cable/dp/B0107RF56O

Hi all, Can anyone please help identify the type of coax the original kit SMA cables are using? I like the convenience of how skinny and flexible these cables are. I hate thick, rigid cables, that

I had mine "lock up" . I removed the cover, disconnected the battery, and measured VCC and found it to hold a small voltage. I shorted to GND, reconnected battery and it came back to life. I hope this

that's the problem, i cannot get an image to load onto it. i cant even get the computer to get the correct driver for it. i have tried two different windows 10 21H2 machines that both show STM32

If the device is in dfu mode, install the firmware you want to use. When that's done you turn it off and on and it should work. The device will remain in dfu mode until you upload usable and working

You need to build a proper test jig when you test components. Stray inductance and capacitance will affect your results. For S21 measurements I use a test board like the one below. You can buy NanoVNA

Hello, The filter is given as equivalent to a 45M15A. The characteristics give a termination of 4Kohm and 2.5 PF. I also found a more traditional test method to see.

Another method used by Epson to measure MCF devices is to use matching transformers to perform the 50 ohm to Zt transformation. https://www5.epsondevice.com/en/information/technical_info/filter/ This

Yes you have the correct procedure. Below is the test setup used by a Monolithic Crystal Filter (MCF) vendor using series resistors and a shunt capacitor to get the required termination impedance..

My NanoVNA-H4 is stuck in DFU mode. when i try to use the DFuse.exe it does not see the device connected to the computer. when i go into device management i see the STM32 Bootloader listed under USB

Hello, Good morning, Very interesting article. I did a translation in French. Now tell me if I’m wrong about the measurement method. 1) We calibrate the NanoVna and then we measure the filter, we