On Tue, Mar 7, 2023 at 03:17 PM, Michael Foerster wrote: I have a NanoVNA-SAA2 and I've found that there is a "Measure" parameter that
I can set to "L/C Match".
So, for my 80m dipole, it shows:
L/C match for source Z0=50.0(ohms)
Src shunt Series Load shunt
1.6uH 298pF
1.1nF 3.4uH
I'm assuming that the descriptions are for an "L" match, but I'm not sure what
the "Src shunt", "Series" and "Load shunt" circuits are.
Can anyone help me to understand this?
|
bALUN Common mode reject Z measurement
Hello,
Is there a way to measure the impedance of a balun (current type, connecting mesh to mesh), but not as rejection in dB, but directly as impedance values using the 2 ports?
As a guide, I have seen this website (), where it exports the sp1 file and lifts it with Excel to convert to impedance, but when exporting from the nano-vna, the curves are not displayed correctly, and I cannot find the fault.
Thanks, LU1FP
|
I have a NanoVNA-SAA2 and I've found that there is a "Measure" parameter that I can set to "L/C Match".
(The forum won't allow me to attach the picture.)
So, for my 80m dipole, it shows:
L/C match for source Z0=50.0(ohms)
Src shunt Series Load shunt
1.6uH 298pF
1.1nF 3.4uH
I'm assuming that the descriptions are for an "L" match, but I'm not sure what the "Src shunt", "Series" and "Load shunt" circuits are.
Can anyone help me to understand this?
--
Mike, W0IH
|
NanoVNA-APP (on PC) can also update firmware, without DFuse. And apparently without special driver.
(It's been a while since I used it, my memory details are fuzzy now.)
I also had plenty of troubles with DFuse Demo.
" I don't know if they still support DfuSeDemo" - -
It appeared to me a few months ago that they do not. I couldn't get their newer program to work with my (non-updated) Windows 10, either.
--
Doug, K8RFT
|
Thank you, Roger.
73,
Gary
toggle quoted message
Show quoted text
At 11:55 AM 3/7/2023, you wrote: On Mon, Mar 6, 2023 at 05:44 PM, Gary - W6GVS wrote:
Exactly where is the file you mention below? I've been unable to
locate it. Thanks.
73,
Gary - W6GVS
At 02:56 PM 3/5/2023, you wrote:
I looked through the file "NanoVNA traces and formulas.doc" and did
not find this there. Maybe there is a newer version of this file
somewhere that contains this, or is it somewhere else?
Attached to this message...
Roger
|
On Mon, Mar 6, 2023 at 05:44 PM, Gary - W6GVS wrote:
Exactly where is the file you mention below? I've been unable to
locate it. Thanks.
73,
Gary - W6GVS
At 02:56 PM 3/5/2023, you wrote:
I looked through the file "NanoVNA traces and formulas.doc" and did
not find this there. Maybe there is a newer version of this file
somewhere that contains this, or is it somewhere else?
Attached to this message... Roger
|
Yes. Otherwise how would it get the firmware updated.
Thanks
Steve
toggle quoted message
Show quoted text
On Mar 6, 2023, at 7:40 PM, Geoff Peters - AB6BT <AB6BT@...> wrote:
?Hi Steve,
Sorry that doesn't work for you. Are you doing this with the device connected?
Perhaps someone else has an idea...
|
Exactly where is the file you mention below? I've been unable to locate it. Thanks.
73,
Gary - W6GVS
toggle quoted message
Show quoted text
At 02:56 PM 3/5/2023, you wrote: I looked through the file "NanoVNA traces and formulas.doc" and did not find this there. Maybe there is a newer version of this file somewhere that contains this, or is it somewhere else?
|
Hi Steve,
Sorry that doesn't work for you. Are you doing this with the device connected?
Perhaps someone else has an idea...
|
Geoff Peters. I have that file but when I follow the instructions, heres what I get. It in the path you listed. On Sun, Mar 5, 2023 at 8:49?PM Geoff Peters - AB6BT <AB6BT@...> wrote: C:\Program Files (x86)\STMicroelectronics\Software\DfuSe
v3.0.6\Bin\Driver\Win10\x64\STTub30.sys
|
Sorry Steve, I do not know anything about updating the nano. I just use mine as it was sent to me.
Larry? N8CWU
toggle quoted message
Show quoted text
On 3/5/2023 3:38 PM, Steve Bowers wrote: Does not find the STM Device in DFU Mode file. I manually tried to locate
and it is not found anywhere. I searched both rprogram x64 and x86 STM
Electronics folders and cannot find a compatible driver. It always loads
the bootloader file.
What is the name of the file? I might be looking for something else.
On Sun, Mar 5, 2023 at 11:33?AM N2MS <mstangelo@...> wrote:
Steve,
I had a similar problem. DFUseDemo was loaded with the Bootloader driver
which I use with STM32 CubeProgrammer for my Malahite DSP2 receiver. It
uses the bootloader mode to update firmware. Sometimes when I exit it saves
the bootloader driver.
To change drivers for the DFU Mode perform the following:
Start DFuSe Demo. If it does not detect any device in DFU mode do the
following:
Start the Device Manager
- Under "Universal Serial Bus devices" you should see "STM32 BOOTLOADER"
- right click on "STM32 BOOTLOADER" and select "Update Driver"
- select "Browse my computer for drivers"
- select "Let me pick from a list of available drivers on my computer"
- Under "Select the device driver you want to install for this hardware".
Check the "Show compatible hardware" box
- You should see the "STM Device in DFU Mode" and "STM32 Bootloader"
drivers.
- Select the "STM Device in DFU Mode" driver.
- Select "Next" and it should display "Windows has successfully updated
your drivers" Close this box
- The Device Manager should show:
"Universal Serial Bus Controllers"
"STM Device in DFU Mode"
- DfuSe Demo will detect the device in under DFU Mode.
Mike N2MS
On 03/05/2023 8:45 AM Steve Bowers <bowxyz@...> wrote:
I got to the point of starting DiFUse and also downloaded the latest
firmware.
Following the directions in the beginners guide I started the DFU demo
program and started the nano in DFU mode as instructed.
However all I see in device manager is STM Bootloader and not Nano in DFU
mode under the USB controllers.
Going back to the DFU demo program and selecting the drop down box where I
should be seeing the device, nothing is there.
I double checked to make sure the Nano is being seen in device manager by
cycling the power switch. Turning it off removes it from the device manager
USB ports.
Any ideas?
Steve
|
Thanks.? More power to nanovna. On Sat, Mar 4, 2023 at 11:15?AM Chris Gardner via groups.io <seaman98= [email protected]> wrote: No problem, enjoy your H4!
On Mar 4, 2023, at 11:17, Steve Bowers <bowxyz@...> wrote:
?Awesome!! Much obliged!!!
Thanks
Steve
On Mar 4, 2023, at 10:57 AM, Chris Gardner via groups.io <seaman98= [email protected]> wrote:
?Greetings, May I suggest that you obtain a copy of this document
(Absolute Beginners Guide). I am sure you will find the information there.
Log In (
/g/nanovna-users/files/Absolute%20Beginner%20Guide%20to%20The%20NanoVNA/Absolute_Beginner_Guide_NanoVNA_v1_5.pdf
)
groups.io (
/g/nanovna-users/files/Absolute%20Beginner%20Guide%20to%20The%20NanoVNA/Absolute_Beginner_Guide_NanoVNA_v1_5.pdf
)
apple-icon-180x180.png (
/g/nanovna-users/files/Absolute%20Beginner%20Guide%20to%20The%20NanoVNA/Absolute_Beginner_Guide_NanoVNA_v1_5.pdf
)
(
/g/nanovna-users/files/Absolute%20Beginner%20Guide%20to%20The%20NanoVNA/Absolute_Beginner_Guide_NanoVNA_v1_5.pdf
)
73¡¯²õ
On Mar 4, 2023, at 09:25, bowxyz@... wrote:
? Help. Newly purchased Nano VNA H4 March 2, 2023.
I've read several posts on the H4 model about firmware and each mention
identifying the proper version and the URL that is listed. Mine does
not
have a URL listed. Version is 1.1.01 [p:401, IF20k, ADC:384k,
Lcd480x320.
Build Time Dec 30, 2021.
I'm sure there are probably newer versions but I am unsure as to the
process to properly update.
Any help would be greatly appreciated.
<apple-icon-180x180.png>
|
The last I looked, support for DfuSeDemo had been dropped in favor of StmCube, which, fortunately, supports far more platforms.
toggle quoted message
Show quoted text
On March 6, 2023 9:25:53 AM CST, N2MS <mstangelo@...> wrote: Steve,
My version of STMicroelectronics DfuSeDemo does not show a driver for Windows 11.
I would check to see if STMicroelectronics has a driver d=for Windows 11 for DfuSeDemo. I don't know if they still support DfuSeDemo.
Mike N2MS
--
Sent from my Android device with K-9 Mail. Please excuse my brevity.
|
On Mon, Mar 6, 2023 at 07:25 AM, N2MS wrote: My version of STMicroelectronics DfuSeDemo does not show a driver for Windows
11.
I would check to see if STMicroelectronics has a driver d=for Windows 11 for
DfuSeDemo. I don't know if they still support DfuSeDemo.
The Windows 10 driver works in Windows 11 Roger
|
Steve,
My version of STMicroelectronics DfuSeDemo does not show a driver for Windows 11.
I would check to see if STMicroelectronics has a driver d=for Windows 11 for DfuSeDemo. I don't know if they still support DfuSeDemo.
Mike N2MS
|
64 bit system and loaded 32 bit dfu tools, so no compat driver?
toggle quoted message
Show quoted text
On March 5, 2023 8:33:54 PM CST, Steve Bowers <bowxyz@...> wrote: Hmm. That file is there but when I point to it, windows 11 says it¡¯s a non compatible file and if I choose to use it the system mdt become unstable. I chose it anyway and the when going back to the update driver process, the dfu mode still does not show up as an option.
Thanks
Steve
On Mar 5, 2023, at 8:49 PM, Geoff Peters - AB6BT <AB6BT@...> wrote:
?C:\Program Files (x86)\STMicroelectronics\Software\DfuSe v3.0.6\Bin\Driver\Win10\x64\STTub30.sys
--
Sent from my Android device with K-9 Mail. Please excuse my brevity.
|
Well, It may be related to Windows 11 and I have only Windows 10 machines.
Sorry I can't be of more help.
|
Hmm. That file is there but when I point to it, windows 11 says it¡¯s a non compatible file and if I choose to use it the system mdt become unstable. I chose it anyway and the when going back to the update driver process, the dfu mode still does not show up as an option.
Thanks
Steve
toggle quoted message
Show quoted text
On Mar 5, 2023, at 8:49 PM, Geoff Peters - AB6BT <AB6BT@...> wrote:
?C:\Program Files (x86)\STMicroelectronics\Software\DfuSe v3.0.6\Bin\Driver\Win10\x64\STTub30.sys
|
C:\Program Files (x86)\STMicroelectronics\Software\DfuSe v3.0.6\Bin\Driver\Win10\x64\STTub30.sys
|
I have Windows 11 pro so maybe that¡¯s the problem.
What is the actual name of the file?
Thanks
Steve
toggle quoted message
Show quoted text
On Mar 5, 2023, at 5:36 PM, Geoff Peters - AB6BT <AB6BT@...> wrote:
?For WIndows 10, in here:
C:\Program Files (x86)\STMicroelectronics\Software\DfuSe v3.0.6\Bin\Driver\Win10
|
Roger Need
Larry Krist - N8CWU