¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date

Re: automatic loading of a nanovna saver cal file?

Cliff
 

I believe it will load Memory 0 on power on so save the calibration to # 0 and it should load it for you on power on.

73,
Cliff, AE5ZA

On Jan 11, 2022, at 14:38, chutton12000 <charlesh3@...> wrote:

Roger -

I am trying to avoid doing a CAL on the nanoVNA screen as it is difficult for me to red it.
So I want to do the cal via nanpVNA aver, but on startupm nanoVNA Saver always says there is no calibration.

So I am still looking for a way to have nanoVNAA Saver automatically load a CAL file that I previously saved after doing a cal via nanoVNA Saver.

Chuckt





Re: automatic loading of a nanovna saver cal file?

 

Roger -

I am trying to avoid doing a CAL on the nanoVNA screen as it is difficult for me to red it.
So I want to do the cal via nanpVNA aver, but on startupm nanoVNA Saver always says there is no calibration.

So I am still looking for a way to have nanoVNAA Saver automatically load a CAL file that I previously saved after doing a cal via nanoVNA Saver.

Chuckt


Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

An early version of 4.2, that's probably why you do not have the
SD slot. You can solder one yourself ...
AFAIK the N variety was only made with NanoVNA V2, a different platform.
Only difference from the regular V2 is the metal case and the SMA to N
adaptors.
A few people made the same modification on their own, but it is a bit of a
hassle as you would
need to get N calibration loads ...

On Tue, 11 Jan 2022 at 03:18, Howard Waxman, WZ4K <wz4k@...> wrote:

Thank you. Bought from R&L on 4/9/2020 and since updated to V 1.0.39;
Kernel 4.0.0. STM32F303xC
I'm interested in the N-connector variant and wonder are they really more
robust? No complaints with what I have.

HW






Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

Looks good, not much of a change except that the new
version is a few dB better from 200-280Mhz.

On Tue, 11 Jan 2022 at 03:16, Stan Gammons via groups.io <buttercup11421=
[email protected]> wrote:

Not sure I did this right, but here is what I got.


73

Stan
KM4HQE


On 1/10/22 6:33 PM, Dragan Milivojevic wrote:
Thanks, as expected, small changes in the layout compared to 4.2.1 that I
have.
Can you post a s2p file when the device is in an uncalibrated state,
port1
terminated
port2 left open?
Here is the image of my board and the s2p file (401 points, 5 segments,
200Hz bandwidth).



On Mon, 10 Jan 2022 at 21:10, Stan Gammons via groups.io
<buttercup11421=
[email protected]> wrote:

Here's a pic of one I got from R&L recently

73

Stan
KM4HQE

On 1/10/22 2:05 PM, Dale - 2W0ODS wrote:

On Mon, Jan 10, 2022 at 03:28 PM, Dragan Milivojevic wrote:

I'm sure it will.
If you are able to, please post the images of the board.
Thinking about getting one just to see if the changes around
voltage regulators on the 4.3 version are significant compared
to the previous one.
Yes no problem at all I will get some pictures, this is the V4.3 with
SI5351, There is another version which is has a MS5351M which is
V4.3-MS,
but I do not know if that one has other changes.












Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

Thank you. Bought from R&L on 4/9/2020 and since updated to V 1.0.39; Kernel 4.0.0. STM32F303xC
I'm interested in the N-connector variant and wonder are they really more robust? No complaints with what I have.

HW


Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

Not sure I did this right, but here is what I got.


73

Stan
KM4HQE

On 1/10/22 6:33 PM, Dragan Milivojevic wrote:
Thanks, as expected, small changes in the layout compared to 4.2.1 that I
have.
Can you post a s2p file when the device is in an uncalibrated state, port1
terminated
port2 left open?
Here is the image of my board and the s2p file (401 points, 5 segments,
200Hz bandwidth).



On Mon, 10 Jan 2022 at 21:10, Stan Gammons via groups.io <buttercup11421=
[email protected]> wrote:

Here's a pic of one I got from R&L recently

73

Stan
KM4HQE

On 1/10/22 2:05 PM, Dale - 2W0ODS wrote:

On Mon, Jan 10, 2022 at 03:28 PM, Dragan Milivojevic wrote:

I'm sure it will.
If you are able to, please post the images of the board.
Thinking about getting one just to see if the changes around
voltage regulators on the 4.3 version are significant compared
to the previous one.
Yes no problem at all I will get some pictures, this is the V4.3 with
SI5351, There is another version which is has a MS5351M which is V4.3-MS,
but I do not know if that one has other changes.







Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

It's a slot for an SD card.
Where (and when) did you get your device from?

On Tue, 11 Jan 2022 at 02:56, Howard Waxman, WZ4K <wz4k@...> wrote:

What is Card1 at top? I do not have that in my variant.

HW






Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

What is Card1 at top? I do not have that in my variant.

HW


Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

Did you notice any change in the performance (presuming that you have both
versions)?

On Mon, 10 Jan 2022 at 22:29, Roger Need via groups.io <sailtamarack=
[email protected]> wrote:

On Mon, Jan 10, 2022 at 07:28 AM, Dragan Milivojevic wrote:


I'm sure it will.
If you are able to, please post the images of the board.
Thinking about getting one just to see if the changes around
voltage regulators on the 4.3 version are significant compared
to the previous one.
Here is how the PCB layout changed between 4.2 and 4.3 in the power supply
area.

Roger






Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

Thanks, as expected, small changes in the layout compared to 4.2.1 that I
have.
Can you post a s2p file when the device is in an uncalibrated state, port1
terminated
port2 left open?
Here is the image of my board and the s2p file (401 points, 5 segments,
200Hz bandwidth).



On Mon, 10 Jan 2022 at 21:10, Stan Gammons via groups.io <buttercup11421=
[email protected]> wrote:

Here's a pic of one I got from R&L recently

73

Stan
KM4HQE

On 1/10/22 2:05 PM, Dale - 2W0ODS wrote:

On Mon, Jan 10, 2022 at 03:28 PM, Dragan Milivojevic wrote:

I'm sure it will.
If you are able to, please post the images of the board.
Thinking about getting one just to see if the changes around
voltage regulators on the 4.3 version are significant compared
to the previous one.
Yes no problem at all I will get some pictures, this is the V4.3 with
SI5351, There is another version which is has a MS5351M which is V4.3-MS,
but I do not know if that one has other changes.





Re: automatic loading of a nanovna saver cal file?

 

Yes, it can when using PC and at least SAVER. Store the cal file on the PC
for later use.

Dave - W?LEV

On Mon, Jan 10, 2022 at 8:49 PM chutton12000 <charlesh3@...> wrote:

Can this be done? I have sometimes forgotten to load the file.

Chuck





--
*Dave - W?LEV*
*Just Let Darwin Work*


Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

On Mon, Jan 10, 2022 at 07:28 AM, Dragan Milivojevic wrote:


I'm sure it will.
If you are able to, please post the images of the board.
Thinking about getting one just to see if the changes around
voltage regulators on the 4.3 version are significant compared
to the previous one.
Here is how the PCB layout changed between 4.2 and 4.3 in the power supply area.

Roger


Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

On Mon, Jan 10, 2022 at 07:28 AM, Dragan Milivojevic wrote:


I'm sure it will.
If you are able to, please post the images of the board.
Thinking about getting one just to see if the changes around
voltage regulators on the 4.3 version are significant compared
to the previous one.
There were quite a few changes to the voltage regulators from 4.2 to 4.3.

Roger


Re: automatic loading of a nanovna saver cal file?

 

On Mon, Jan 10, 2022 at 12:49 PM, chutton12000 wrote:


Can this be done? I have sometimes forgotten to load the file.

Chuck
It automatically loads slot 0 cal data on the most NanoVNA models. IIRC some versions of firmware can recall the last configuration used.

Roger


automatic loading of a nanovna saver cal file?

 

Can this be done? I have sometimes forgotten to load the file.

Chuck


Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

Here's a pic of one I got from R&L recently

73

Stan
KM4HQE

On 1/10/22 2:05 PM, Dale - 2W0ODS wrote:

On Mon, Jan 10, 2022 at 03:28 PM, Dragan Milivojevic wrote:

I'm sure it will.
If you are able to, please post the images of the board.
Thinking about getting one just to see if the changes around
voltage regulators on the 4.3 version are significant compared
to the previous one.
Yes no problem at all I will get some pictures, this is the V4.3 with SI5351, There is another version which is has a MS5351M which is V4.3-MS, but I do not know if that one has other changes.


Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

On Mon, Jan 10, 2022 at 03:28 PM, Dragan Milivojevic wrote:


I'm sure it will.
If you are able to, please post the images of the board.
Thinking about getting one just to see if the changes around
voltage regulators on the 4.3 version are significant compared
to the previous one.
Yes no problem at all I will get some pictures, this is the V4.3 with SI5351, There is another version which is has a MS5351M which is V4.3-MS, but I do not know if that one has other changes.


Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

I'm sure it will.
If you are able to, please post the images of the board.
Thinking about getting one just to see if the changes around
voltage regulators on the 4.3 version are significant compared
to the previous one.

On Mon, 10 Jan 2022 at 15:41, Dale - 2W0ODS <dale.robins@...> wrote:

On Sun, Jan 2, 2022 at 03:47 PM, Dragan Milivojevic wrote:


You are right, it is completely different. One is running a part
out of spec, betting on manufacturing tolerances, the other
is relying on the fact that manufacturers relabel chips.
As for clones etc, those that buy at authorised resellers
have no such dilema.

I just received another NanoVNA for the collection, a NanoVNA-H4 Genuine,
V4.3.
And this one came with a STM32F302CBT6, 32Khz clock xtal and also SD Card
slot with cutout.
I'm curious to check this MCU over, I have a genuine ST-Link V2 also Keil
development boards for this series of MCU and some STM discovery boards (I
can easily remove this MCU and solder it there)
I have loaded the latest Hugen/Dislord firmwares and it's working okay, I
hope it stays this way in the future.







Locked Funds for 2022 nanovna-users group annual fee

 

All,

As I posted before, we have sufficient funds pledged to pay the groups.io fee for 2022.? The response, in under two days, has been overwhelming.

**Further pledges are not necessary**.

We will need to do this every year going forward, so there will be ample opportunity to contribute in the future.

Thanks to everyone who has pledged to support the group.

The next steps for collecting the pledged funds and paying the fee to groups.io will occur starting next week.

DaveD


--
This email has been checked for viruses by Avast antivirus software.


Re: Where to buy a NanoVNA H4 HW rev 4.3?

 

On Sun, Jan 2, 2022 at 03:47 PM, Dragan Milivojevic wrote:


You are right, it is completely different. One is running a part
out of spec, betting on manufacturing tolerances, the other
is relying on the fact that manufacturers relabel chips.
As for clones etc, those that buy at authorised resellers
have no such dilema.

I just received another NanoVNA for the collection, a NanoVNA-H4 Genuine, V4.3.
And this one came with a STM32F302CBT6, 32Khz clock xtal and also SD Card slot with cutout.
I'm curious to check this MCU over, I have a genuine ST-Link V2 also Keil development boards for this series of MCU and some STM discovery boards (I can easily remove this MCU and solder it there)
I have loaded the latest Hugen/Dislord firmwares and it's working okay, I hope it stays this way in the future.