开云体育

Hello mainly Mario and Syd For rx I find that both Lime MIni and Pluto work fine on Quisk at 1MHz bandwidth and more.? Turn off transmit. For transmitting Pluto will not work satisfactorily on Quisk

Thanks Mario, I was trying it on HF and BBC Radio 4 on 92.7MHz with no luck. I'll have a closer look with quisk. 73 ... Sid.

Hello Bruce and Murray, I am sorry about the long delay in responding, but I am busy trying to finish the HL2 IO board. I will reply when I get time. Jim N2ADR

Hi Sid, LimeSDR and SDRAngel works quite well. I frequently use it for transmit of arbitrary waveform files. However the use of the software needs some effort. Its more an experimental plattform than

Jim gave up on getting the Mini to work in quisk, so this sounds great. I wonder if it'll also work with the LimeSDR USB .... I've never been get it to work with any software -- sdrangel looked like

Hi Bob, if you could share your source code maybe here in the files section that would be great. I at least managed to receive and transmit with Quisk and LimeSDR Mini via Soapy. This works much

Hi Mario Well in principle it should work!! I have made the Lime Mini work very well on ordinary simplex and had several QSOs on 2m.? I can send you a bit of code that implements this in the hardware

I'm having trouble getting "Digital Rx0 Output" to, well, output.? I'm on Linux running alsa but not pulse.? There are two soundcards, an internal and a USB external.?? I can use either and/or

Hi Bob, are you still using LimeSDR with Quisk? I intend to try as Lime-Mini with Quisk but my favourite mode would be transmit 2.4GHz and receive on 1100MHz (from my sat LNB). Do you have a clue if

What answer do you get when you send ZZAR; ??? That will tell you the format. Looks like I may need to update Hamlib to distinguish between SmartSDR and PowerSDR -- PowerSDR uses the +123 format and

I was just now looking into updating my version of quisk preparatory to implementing the flex ZZAR commands in cat/serial-port software, but have a question (maybe this arises because I am

A few more bug fixes and tweaks. Moved code to 4.2.19; zipo file contains delta from source. DStar TX audio still a bit dodgy. Dave

Thanks Jim! I will check how the remote serial port works in my set up and report back. Due to other commitments that might take a week or 2. 73s, Peter, PA3BIY Op 18/05/2023 om 18:23 schreef

I added the Flex ZZAR command to the Hamlib interface. This controls the AGC level from -20 to +120 dB. The levels are mapped to the Quisk AGC level 0.0 to 1.0. The Flex AGC operates as a limiter but

Below is a screenshot showing quisk's confirg screen with error on first start, along with pavu immediately after that. Whereas pavu showed no input devices before quisk started, the input devices do

You are probably right (according to man pages). And according to that man page, it may even be possible that packets to this socket get precedence over packets from *other* interfaces. I was never

I will add the Flex ZZAR command to the next release. Jim N2ADR

IMHO any traffic generated on the machine will obey the priorities. I.e. imagine some upload going through the interface and IMHO such packets will be skipped in the queue by the SO_PRIORITY traffic.

I am not an expert, but I think these priorities are used by *routers* to make decisions, as far as I know they have little effect on packet handling inside *computers*. If this were the case, they

Hi, this was originally mentioned in [1] and it seems some SDRs use it. I have been using it for some time with quisk and HL2 and I haven't seen any problems. I also haven't seen any visible