开云体育

Download the Meter Protocol document. Read it and the Manual for the 600Pro II. SOFTWARE LDG Electronics does not provide any software for controlling the AT-1000ProII or AT- 600ProII via the meter

Hello, I found a program to control the LDG 1000Pro II in HitHub, which I think may be valid for the 600. You can even see the direct, reflected and PEP power Angel EA4GIG De: [email protected]

The cable is home brew (software and cable instructions are on the AT-600 Pro II and AT-1000 Pro II product pages)?- here is the cable:

Software??? What software??? The only control I know of for the 600Pro is via it's front panel, and via the interface cable for Icom and Yaesu rigs. Ed - ad7gr

I reported this issue to them back in December. There was suppose to be a new version that came out in January to resolve this that never did. Unfortunately, there’s no fix to my knowledge at this

I downloaded software for this tuner but cannot find instructions on using it with software. There is only a 1/8 plug on the back and no mention of cable using and to which rigs it works on. How do

Hi all, I am back using the LDG software to control my AT600 Pro II unit (OS = Win10 PC) Everything works well (switching antennas, tuning) but one function does not react as I would expect: the

Good day all! I just received my AT-200ProII, hooked it up and started tuning. So far so good with one exception. When I key up the radio is not dropping the RF and switching to CW to auto tune. Is is

Tom, From the advertising. "The LDG AT-200 PC is the first automatic antenna tuner specifically engineered for USB computer control." If your handy with a soldering iron (or know someone who is) the

Hi Steve, Yeap; that's the user manual procedure to change the SWR threshold.? I've tried it before I tune up a frequency and after tuning on a frequency.? On the SWR? scale the 1.7 is the only

Thank you Neil for your suggestions! I assume there is no way to solve my needs just by a setting of AT-200PC -therefore your proposals are the only way I can see. I will think about which solution

Terry, Have you tried this? Automatic Tune SWR Threshold: When the AT-1000ProII is in fully automatic tuning mode, an automatic tuning cycle will begin any time RF is present and the SWR has exceeded

Steve, I agree, that's what the manual says.? I've asked LDG Tech Support about why my unit will not allow me to change the threshold setting and they effectively just shrugged their shoulders.? I

Hi David, Thanks for the explanation; although I don't fully understand it.? The antenna may be using the coax as a counterpoise, I don't know, however, I do have a 50' counterpoise attached to the

Tom, I can see four solutions to this. 1. Continue on using the software (especially if your computer is always on). 2. Using two switches (1 DPDT, 1 SPST), a resistor and a diode add an option of

The reason this is happening is probably in the way the EFHW antenna is operating. Many end fed antennas use the coax feeding the antenna as a form of a counterpoise. Your antenna analyzer did not see

Hi, I'm running an AT-200PC since some years and have a question regarding the two antenna out ports: have ' Ant 1' connected to a random dipole antenna 80 - 30m band and at 'Ant 2' an antenna for 20

Pedro, Yes. I do the same when using my AT-600Pro as well as my Z-11ProII 73, Ed - ad7gr Yes, it's thue, But, afterautomatic tune you can manually adjut at best swr value it and store it. I do this

Yes, it's thue, But, afterautomatic tune you can manually adjut at best swr value it and store it. I do this procedure with my at100proii when i need it. That's not possible with the at1000??

Terry, According to the online user manual (on page 12) the lowest the threshold can be set is 1.7. Steve, AI3KS