开云体育

: I am using the antenna tuner but want to be able to put it into "bypass" mode when it tries to tune again in the middle of a QSO. The instructions say to press the TUNE button momentarily and the

can anyone recommend the correct cable to use with my ftdx101d radio and the ldg z100 plus

I have an YT-100 setup with a FT-857 radio.? The LED on the tuner is blinking constantly.? After some searching online I found a couple suggestions, primarily about reseting the radio and changing

HI, thanks for letting me join your group. I have today received the faulty Z-100 purchased from another ham, on opening up the unit i see a normal transistor ( 2sa1013) in place of Q4, i need to

Ken, I just checked and Cheapham.com has the LDG Y-ACC Yaesu Interface Cable - CLOSEOUT sale for $2.49 73, Ed - ad7gr

I have had this factory new tuner for about 12 hours now, no matter what I do it will not automatically lower transmit power and change to CW mode for tuning.? I am using an original LDG IC-PAC cable

You were luck if you got a control cable for your tuner from LDG. I tried to order a cable for my Z100 and was told they are out and most likely want be restocked until 2023. ? If you leave them a

Sorry if I duplicated this. Open it up and flip the circuit board over. Look to see if any of the coils or coils on toroids have bad solder joint(s). Some can get fairly warm and open a bad solder

Can a Kenwood ts-2000 to a AT-1000 pro have tuning function? I had a KT-100 hook up? that way? Just asking. K6DLC -- Daniel Curry US Air Force Veteran PGP: AD5A 96DC 7556 A020 B8E7 0E4D 5D5E 9BA5

The YT-100 requires approximately a minimum of 10 watts of RF output for reliable operation. FT-817 output is 5 watts as I recall.The YT-100 manual states it may work for some users at 5 watts. That

Hello to all of you I do know from the manual that the YT-100 it is not suitable for the Yaesu F-817, but I wonder if in the meantime there has been some "upgrade" about this matter , in other words,

Thanks for everyone's patience as we upgrade our systems. Here are some updates for May 2022. 1] We continue to get bombarded by Russian hackers that are causing web and phone delays. Here is a sample

Neil, Thank you for the info. I just order the cable from Amazon. Also one of the zip file was a cheat sheet. It gave me the info on changing the watt meter from 100 to 1000 reading.

Daniel, If you have a AT-1000proii the manual is below https://ldgelectronics.com/products/desktop/at-1000proii/ If you only have a AT-1000pro the manual is in the following directory.

Thanks, Ron. Well, problem is that while tuning, the amp's internal protections shut it down when the SWR goes above 3:1. Right now, I'm using a SGC 239 remote tuner, which does tune well on <5W, then

Hello all, I have some questions about the operation of my at-1000pro. 1) what is the plug? specific size for the 12 volt connection on the back of the tuner? 2) It mentions that I change the power

Give them a call as they are very good at customer support. They just sent me on for one of my tuners as it just plugs is to a DIP socket.

Hi Neil, Thanks for info. I downloaded the zip file and found the manual and schematics. No hex file for the PIC.73'sSteliAE6OR

I have burnt the wiring on L2 and wonder if anyone can tell me the number of turns of wire it has and also the diameter of the wire. Thanks in advance Ian ZL2AIM

Stelian, The LDG site is up. If you go to the group site and files you can download a ZIP file on the IT-100 (Includes circuit diagram and manuals etc) For info there are 25 files on discontinued