开云体育

My RT-600 stopped as well. It lasted 5 years outside in a "weatherproof" box. I tried to fault find it but gave up. However leaving it in the warm dry shack with the lid loosely fitted for 6 months it

My RT600 tuner has stopped working.?? The bias Tee is ok.? The red light on the tuner circuit board flashes when the power is turned on and then goes off.? When powered up, one of the relays used

Schematic is in the "files" section. 3200pf. Mike N3PM

Well, it happens I guess :-) I've an extremely burnt capacitor in my AT-1000 ProII. I've been looking around for a schematic, but can't seem to come up with anything. I'd be grateful is anyone can

Hi All, For the IC-104HG interface cable for the Z100A, what do the "Start Blue" and "Key Green" wires do? Thanks, Steve, W2MY

? ? Thanks I found my problem. Operator error. ???♂? Allen

Hello, I had the firmware version 1.8 as standard, and Mark sent me version 1.7 Could the newer version have some kind of bug?

What version did they send to you? Just wondering if my chip is the latest version.? Thank you,Dave, KJ7WUZ? On Mon, Mar 17, 2025 at 10:07, Adam<k1adw@...> wrote: I appear to have had the same

What version of F/W do you currently have that has the SWR LED problem? And what version are they sending you? Scott KK7RFX

Thanks everyone I reached out to LDG. Sorry for wasting the bandwidth here but do appreciate the group and the answers. 73!

Stop [email protected]> wrote:

Program seems old and uninstall able on windows as is. W4JDY / EM79xr / ITU 8 / CQ 5 Sent: Saturday, 22 March, 2025 00:26 To: [email protected] Subject: [ldgelectronics] Serial Data issue on

Hi, I sent a message to LDG customer service and spoke with Mark. After verifying the problem, they sent me a different firmware, and now the AT1000 pro2 is working correctly. I'd like to thank the

LDG is very good about replacement parts. If parts are available you likely need just to ask LDG and they will send it out to you. If you do get a replacement, I’d suggest a couple of 5V, unipolar

Hello, For years I have been using a software program called LDG Tuner Control, to interface my AT-1000ProII Autotuner ( https://github.com/Efpophis/LDGControl ) with my PC by using the meter jack at

Hello, Using a Z100 Plus Radio and setting up a go box with the IC-705.? If I put the Z100 Plus in Bypass, will it pass the VHF/UHF Frequencies.? I was hoping to have a switch to go between the

Never mind……… Sent: Wednesday, March 19, 2025 2:37 AM To: [email protected] Subject: Re: [ldgelectronics] z-11 Pro firmware [Edited Message Follows] No of course, I don't use the ATU on

WOW – I did not know the Z-11-PRO was rated to work on 70cm. I was almost certain it was from 1.800-MHz to 54.000-MHz only. I never considered using it because my UHF antenna is a very low SWR from

No of course, I don't use the ATU on the 70 cm band, this tuner is connected to the Yaesu FT-857 which also has the 70 cm and while transmitting on this range the ATU attempts tunings but of course it

Z-11: 1.8 to 54.0 MHz coverage So how are you using this tuner on 70cm??? W4JDY / EM79xr / ITU 8 / CQ 5 Sent: Sunday, March 16, 2025 12:49 PM To: [email protected] Subject: [ldgelectronics]