开云体育

Well if it’s like my AT100, while transmitting a carrier, you can hold down the tune button for a few seconds and let go and it will try to get a better match and because of it’s memory, it will

Hi Pedro, Good thought; thank you, I had not thought about changing the set value. My SWR threshold is set at 1.7 and I cannot change it.? When I try, the 1.7 light flashes but it does not change.

Terry, Not familiar with that Chameleon EMCOMM II, antenna had a look around and people seem happy with it. Did not find anyone saying they added a choke to improve the antenna. Have you tried it

Hi Terry, I think you mush setup the threshold to the desired máximum swr. You can check the procedure at page 12 of the manual. Regards Pedro Barcelona

Hi Mike, Thanks for the hint; I'm not using an amphlifier in my current set up. Late yesterday I received the radio interface cable (IC PAC) & an extra coax cable. ?Today, I created a coax balun (21

Hi, I'd like to add one thing. If you're using an amplifier turn off the Auto Tune feature. This will not allow the tuner to automatically tune at whatever power the amp is putting out. Mike KD9CK

To All Who Have Replied, Thank you.? Yes, I have the manual and I have it printed for easy reference.? And, I am using it. My version of the manual does say if one is not using the optional radio

I use the interface cable but for fine adjust I use RTTY reducing the power to 10watts aprox and ptt-ing with the mic.

Hi Terry, I presume you did read the manual. The manual states you can use AM CW or USB but must modulate for voice. Also states run LOW power as when you first start tuning you may get a high SWR and

Terry, You cannot use USB or LSB as there is no RF unless you are speaking and then it is not steady. Try again using AM, Steve, AI3KS

What do the instructions for the AT-1000 ProII say to do, pretty sure the unit needs a steady carrier to tune, at least mine does. That means not to use side band. John VE3KKQ

Hi Steve, I'm keying the mic in USB and LSB modes (14.270 & 7.240)? My IC-7000 is set at 80% power. I have ordered the IC-PAC cable; it is suppose to be delivered on Tuesday.? In my area USPS hasn't

Terry, Are you also keying the 7000 in AM or RTTY mode with reduced power? The tuner needs RF in order to tune. You should hear relays chattering as it does. I have a 7300 here with an AT-100 and

Hi Everyone, I have a antenna, a Chameleon EMCOMM II, that I am trying to install and I'm not having any success. I have an Icom IC-7000, with a built in Tuner/Call function, but I currently do not

Angel, Cannot see anything in the Meter Protocol Document that allows you to all that you want. http://www.vk2byi.com.au/manuals/ has the Meter Protocol Document. I suggest that you contact LDG

Hello I usually operate my station remotely. That is why I am looking for a software for the AT-1000 Pro II, which allows me to operate the tuner remotely, but which can also display: A) direct power.

Dave, Ladderline length is also a necessary part of the solution.?? For instance, I have a 135' Doublet and my 112' home made open wire ladderline terminates at a 1:1 balun on the outside of my

Sorry, I thought it showed at the top of the message. Name is Dave call sign is kbgp seven GP located in East Olympia Washington

Nice info. I believe those tuners are L type?and if it doesn’t have the ability to reverse inductance and capacitance during the tuning process, then if the transformed impedance falls to far below

Dave, I have been using a fan dipole fed with open wire for some time. Originally I was using a 1:1 balun for the transition between the 50 ohm co-ax and ladder line. Had some issues with lower