开云体育

Thanks for your responses?Very interesting......I shall look into the bimini supports,?and follow up. There is a wrap of tape around the portside-most support’s seam so maybe?a previous owner was

Good point which I had forgotten.? We also drilled drain holes in the bottom of the SS bimini support tubes.? This does prevent water build up inside.

Hi Brian We had the same issue. I opened the panel above the place where the water appeared and checked the seal between the deck and the cabin wall. I found a small area without sealant, towards the

Might be a good time for me to mention the supports for the 410 Bimini. The 2 supports as well as the 3 at the “windshield” (front) don’t have any drain holes in the bottom. Now water

We also found water in a similar location.? We found (eventually) that the water was getting inside the SS tubes that support the bimini.? We resealed the base of the tubes where they are screwed in

I'm not quite sure where you mean, but I had a leak around the external chartplotter above the steering wheel which led to drips onto the chart table inside. hope that helps. -- Peter

I own a 2007 380s2, hull#409. Recently I noticed a small but definite water accumulation above the nav station on the horizontal surface that creates the coach roof just inside the port aft cabin.

2017 l42 Would like to change the current isotherm swing open refrigeration unit in the salon to a 2 drawer unit but not sure if the Dr160 will fit in same space. ?Anyone out there have a 2019 which

After 9 happy years cruising in the Med, the time has come to say goodbye to our SY Dakini (Lagoon 421, hull # 220 - built November 2010). She is registered in Switzerland and is VAT not paid. Single

Thanks for that suggestion, have checked with flexifold and they say that it is not needed, but will try just to cover that base. Cheers Rex

I have a L380 #311 with Volvo 29 hp saildrives. Currently I have Volvo 3 blade folding props that work Ok. I would like to have two 3 blade aluminum as spares. Does anybody know the diameter and

I've had Flexofolds on four different boats. You're probably way ahead of me on this and it may already have been suggested to you, but since I didn't see you mention it, I've found the most important

I have this ongoing issue with one set of my flexofold 3 blade props. It won’t open when going astern. All good going forward. I have had the prop inspected and measured by prop engineer and no

Hello, our Lagoon 440 029 is missing aft cabin headrests (they were missing when we bought the boat, but the velcro attachments are present). does anyone have closeup images and hopefully even full

Hello dear Lagoon owners; We are looking for a Lagoon with following criterias; Model: Lagoon 420, 421 Year Range: 2013-2016 Flag: Turkish preferably. Happy to hear other options Private yacht only,

after 2 years on lithium, we are very happy live on boards. Have 400 ah lithium and 360 w of solar and for our boat that is mainly 12 V is more than enough. Our solars are on davits and can rotate,

Hi, I like the simplicity of this. Design. What’s the mechanism to alter the angle. Please send pictures. Should I just install them flat? I am looking at 4 or 5 390w panels. Do you suggest going

Obviously the wrong material for the job/location. ?Rather than buy “like kind” replacements from Beneteau, I would remove the existing parts and tanks then to a local machine shop. Have them

Byrne, The Beneteau site has them listed as (I believe) a “Tiler Leaver”. Part # 046766, #41 on the diagram. Your not going to like the price though, $3K. Steve in Solomons MD 410 S2 E

These are the rudder head fittings (quadrants) attached to the port rudder on my Lagoon 410. It appears that corrosive sea water leaked through the emergency tiller access through the hatch cover