That's most interesting John.? If have time tomorrow I'll give this a try.? Off to Dayton Tuesday for the week. Hamvention.

Peter ve3poa?

开云体育

Hey, the dots have suddenly appeared. But also, some spurious short wires have appeared, coming from dots and going nowhere. The imported symbols are smaller than the native KiCad symbols and the capacitors don't have thick plates.

Yes, I did, but the connections and crossings seem to be preserved. Now I wish that there was a way to assigning the same footprint to all the resistors in one operation, instead of 61 separate operations. It's a smaller issue with capacitors, because they don't have all the same footprint.

On 2024-05-12 21:04, Peter Ayearst wrote:

John,

Did you find the same thing as I fid?? Connection dots did not import jnto KiCad?

Peter

--
OOO - Own Opinions Only
Best wishes
John Woodgate, Rayleigh, Essex UK
Keep trying

开云体育

Thanks, but I do not know what 'table layout view' is. How do I find it??

I notice that the BOM generator is buggy. It doesn't cope correctly with several components having the same value and footprint. If it's not easy to put, say C5, C6, C7 all in column 1, it would be better to use three rows than spread the data across seven columns, with wrong content in several of them.

You should be able to do that on the table layout view Just cut and past
as required in the footprint field. 

Andy


On Sun, 12 May 2024 21:40:31 +0100
"John Woodgate" <jmw@...> wrote:

Yes, I did, but the connections and crossings seem to be preserved. Now 
I wish that there was a way to assigning the same footprint to all the 
resistors in one operation, instead of 61 separate operations. It's a 
smaller issue with capacitors, because they don't have all the same 
footprint.

On 2024-05-12 21:04, Peter Ayearst wrote:

John,

Did you find the same thing as I fid?? Connection dots did not import 
jnto KiCad?

Peter
  

-- 
Signature OOO - Own Opinions Only
Best wishes
John Woodgate, Rayleigh, Essex UK
Keep trying

-- 
This email has been checked for viruses by AVG antivirus software.

You should be able to do that on the table layout view Just cut and past
as required in the footprint field.

Andy


On Sun, 12 May 2024 21:40:31 +0100
"John Woodgate" <jmw@...> wrote:

Yes, I did, but the connections and crossings seem to be preserved. Now
I wish that there was a way to assigning the same footprint to all the
resistors in one operation, instead of 61 separate operations. It's a
smaller issue with capacitors, because they don't have all the same
footprint.

On 2024-05-12 21:04, Peter Ayearst wrote:

John,

Did you find the same thing as I fid?? Connection dots did not import
jnto KiCad?

Peter

--
Signature OOO - Own Opinions Only
Best wishes
John Woodgate, Rayleigh, Essex UK
Keep trying

--
This email has been checked for viruses by AVG antivirus software.
www.avg.com

开云体育

Yes, I did, but the connections and crossings seem to be preserved. Now I wish that there was a way to assigning the same footprint to all the resistors in one operation, instead of 61 separate operations. It's a smaller issue with capacitors, because they don't have all the same footprint.

John,

Did you find the same thing as I fid?? Connection dots did not import jnto KiCad?

Peter

John,

Did you find the same thing as I fid?? Connection dots did not import jnto KiCad?

Peter

开云体育

No need to reply: I found out how to do it.

Thank you. Would you please tell me how you did that, because I can't find? a way that works.

On 2024-05-11 22:34, Peter Ayearst wrote:

I did? import a LTspice schematic but not sure if it was v8.02 or not. It seemed to work ok except the connection dots did not show up in the schematic.? ?KiCad did know there was a connection.? Simple schematic not much of an issue but anything else would be troublesome.

Peter

--
OOO - Own Opinions Only
Best wishes
John Woodgate, Rayleigh, Essex UK
Keep trying

开云体育

Thank you. Would you please tell me how you did that, because I can't find? a way that works.

I did? import a LTspice schematic but not sure if it was v8.02 or not. It seemed to work ok except the connection dots did not show up in the schematic.? ?KiCad did know there was a connection.? Simple schematic not much of an issue but anything else would be troublesome.

Peter

I did? import a LTspice schematic but not sure if it was v8.02 or not. It seemed to work ok except the connection dots did not show up in the schematic.? ?KiCad did know there was a connection.? Simple schematic not much of an issue but anything else would be troublesome.

Peter

开云体育

Can version 8.02 import a Spice schematic, specifically an LTspice schematic?

开云体育

I found that if I 'select all', the rotation triangles on the toolbar work correctly, but the mirror triangles do not reflect the tracks. I can't believe that is intentional.

开云体育

You are lucky. Mine is a bear-faced liar.

Personally I prefer to follow the advice of my teddy bear; he's never
been wrong about anything ;)

Regards,

Robert.

* Plain text email - safe, readable, inclusive. *

On 24/04/2024 08:43, Bernd Wiebus via groups.io wrote:

You can also ask your juristical solicitor and, of course, you should
ask your priest, because some people think, open source is from the
devil. ;O

Personally I prefer to follow the advice of my teddy bear; he's never
been wrong about anything ;)

Regards,

Robert.

* Plain text email - safe, readable, inclusive. *

is it open source to all company?

So look here:
?
?

And notice "GNU General Public License(GPL) version 3 or greater"

For GPU GPL 3 look here:


and


You can also ask your juristical solicitor and, of course, you should ask your priest, because some people think, open source is from the devil. ;O)

With best regards: Bernd Wiebus alias dl1eic




?

Gesendet:?Mittwoch, 24. April 2024 um 08:27 Uhr
Von:?"window0619 via groups.io" <window0619@...>
An:[email protected]
Betreff:?[kicad-users] Question
is it open source to all company?

开云体育

开云体育

开云体育

Use drag. I have it assigned to the tab key, I think the default is G.