开云体育

I'd like to progran my CVP EasyDCC AD4 Accessory Decoder's via
DecoderPro but there no configuratrion file for them. Has anyone
produced an AD4 config file? If so, would you sharing it with the
group.

Thanks
Bob

Black Bart,
Here is a comment I made back in 5-24-02!

"Group,
Another plus for our beloved DecoderPro. I bought a group of CVP AD4
accessory decoders for switch motors. Not wanting to do these by throttle I
first used PR1DOS connected through the MS100. I already knew the PR1
'standalone' wouldn't work from another report. I could not get the PR1DOS
through the MS100 to work at all. Many tries.
I connected up DecoderPro through LocoBuffer and used the single CV
programming tool. Worked each and everytime. While I did have to put in
numbers for the CV's it's quite easy as they are explained in the AD4
instructions.
So another que for DecoderPro. I think a pane for the AD4 would
probably be easy but that's another one for the tomorrow file!"


Jon Miller
AT&SF
For me time has stopped in 1941
Digitrax DCC owner, Chief system
NMRA Life member #2623
Member SFRH&MS

At 7:39 PM +0000 8/4/02, original_black_bart wrote:

I'd like to progran my CVP EasyDCC AD4 Accessory Decoder's via
DecoderPro but there no configuratrion file for them. Has anyone
produced an AD4 config file? If so, would you sharing it with the
group.

I started to throw together a pane for this last night. In the process, I discovered that the address is split between two CVs, much like the long address in a locomotive decoder. It's inconvenient to have these show up as two fields, so I'm going to have to write a couple of lines of code to handle this.

More to follow.

Bob
--
--------------
Bob Jacobsen (Bob_Jacobsen@..., 510-486-7355, fax 510-495-2957)
At CERN until August 10, replies may be slow.

I'd like to progran my CVP EasyDCC AD4 Accessory Decoder's via
DecoderPro but there no configuratrion file for them. Has anyone
produced an AD4 config file? If so, would you sharing it with the
group.

The AD4 splits its address across two CVs, which is a bit of a pain to do manually. I wrote a little bit of code so that we can specify that in a decoder file, and created an AD4 definition file to test it. It will be in the next test installer, probably available Thursday.

I don't have an AD4, though, so will be relying on you guys to test it and comment on whether it's OK.

Bob
--
--------------
Bob Jacobsen (Bob_Jacobsen@..., 510-486-7355, fax 510-495-2957)
At CERN until August 10, replies may be slow.

Bob,

If you need one, I got one to loan you.

Bob Jacobsen wrote:

I'd like to progran my CVP EasyDCC AD4 Accessory Decoder's via
DecoderPro but there no configuratrion file for them. Has anyone
produced an AD4 config file? If so, would you sharing it with the
group.

The AD4 splits its address across two CVs, which is a bit of a pain
to do manually. I wrote a little bit of code so that we can specify
that in a decoder file, and created an AD4 definition file to test
it. It will be in the next test installer, probably available
Thursday.

I don't have an AD4, though, so will be relying on you guys to test
it and comment on whether it's OK.

Bob
--
--------------
Bob Jacobsen (Bob_Jacobsen@..., 510-486-7355, fax 510-495-2957)
At CERN until August 10, replies may be slow.


To unsubscribe from this group, send an email to:
jmriusers-unsubscribe@...



Your use of Yahoo! Groups is subject to

Best Regards,

Mark Gurries
Linear Technology
Power Supply & Battery charger Applications Engineer/Manager
---------------------------------------------------------
Model Railroad Club and NMRA DCC presentations are at:

--------------------------------------------------------
Audio Enthusiast (Love SAE equipment)


----------------------------------------------------------