开云体育

Version 4.10 was listed on the Jmri.sourceforge.net main page as current, the download page is correct. I'm sure Bob will correct. -- Peter Ulvestad JMRI Users Group Moderator - http://www.jmri.org (

Thank you all. I have always gone to sourceforge as someone mentioned. I will go to jmri.org. I figured it was something like a new website...great responsiveness in the group...and kind.? Mike

I just went to source forge. All versions are listed. I do not see anything about any version being recommended over any other. Jim

Sort of going backwards now.... The name of my CU. connection is, as I said earlier, 'cu.usbserial- A9KJ71D9'. The ' A9KJ71D9' is thr serial number of that device. I upgraded my JMRI to 4.14,

Bob, Jmri.sourceforge.net is still up and alive and showing 4.10 as current production version. I saw that posted a few days ago on another forum. Tom Wilson Colorado Springs, CO

Go to Preferences->Defaults and make sure everything is set to MRC and nothing to Internal. Also please make sure you are running JMRI V4.14 or V4.15.1 or the "Internal" problems may occur again in

I have a 'cu.usbserial-A9KJ71D9' and this is a selection in the 'serial port' option for a connection setup. Still nothing.

As Peter mentions, 4.14 is current and available at http://jmri.org/download/ If you’re seeing an earlier version at some URL, could you let me know where? I’d like to get that fixed. Bob -- Bob

Loaded the FTDI USB drivers and tried again. Found an instance of this error message for each time I tried to start DecoderPro. ?No error message were displayed on screen. ? 2019-01-05 19:54:31,524

The NCE DCC systems don't actually support Power OFF/ON commands: - With the Power Pro system we fudge it by using the ENTER PROG TRACK MODE and EXIT PROG TRACK MODE commands. This works with the

Congratulations Steve, glad to hear it. Maybe you can help my friend John Umberger, also posting in this thread, to get his PR4 to work. We have tried everything, we tjink. Maybe you can point out

Marc, I am using a DCS 200. John

Guys The update window that I use shows ALL production versions and ALL test versions. Shown down the left side of screen. http://jmri.org/install/WindowsNew.shtml Gerry -- Gerry Hopkins MMR #177

Hi Steve, Am I OK to copy / paste your advice for use on the JMRI MERG CBUS Hardware Support page? I'm presuming a CANUSB4? Thanks, Steve.

I just took a look and the PowerCab doesn't have the concept of track power being on/off. At least the notes I have don't identify any command for track power. If that is true, JMRI shouldn't even

Mike S, What website was saying 4.10.xxx as the current JMRI version? Jmri.org is the official site for JMRI. And right now, 4.14 is the official production version. We've already started on the next

While that may be true for the PR3 (I haven't checked, and I have no inclination to do so), it certainly isn't true for the PR4. Direct from the PR4 product page on the Digitrax Web site: <quote>

<http://www.ftdichip.com/Drivers/VCP.htm> Irrespective of DCC system, there are some basic rules for troubleshooting any USB-attached device to a Mac. Plug your device into your Mac. Go to "System

Yeah, I'm one of those who claims the PR4 works, because mine Just Does. And no, I don't use it in "connected mode" through a command station for programming. As a matter of fact, the programming

Don W, If you are building panels using Internal devices because you don't know which real system you will use, then assigning 'usernames' to each item will save you a lot of effort later. If all the