¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io

Driver Board Replacement, adjustments required?


 

Hello All,
I have a couple of 7ks. ?A newer one works perfectly, as far as I can tell. ?An older one has low output and the driver board is suspect. ?I intend to replace the driver board - new parts and board are on the way.?
My question: ?following the board installation, are the adjustments (as recommended by Icom) necessary or optional? ?A Service Bulletin of Feb/2010 outlines a multi step adjustment procedure requiring equipment I don¡¯t have - that¡¯s the reason for this question. ?
I want to replace the board myself, I¡¯m capable of doing that. ?But the adjustments I cannot do without purchasing equipment at expense. ?
So, ?if the adjustments are necessary, then I might just as well replace the board and send it to Icom to do the adjustments¡­ may be cheaper than buying new equipment.
Any thoughts or advice from this group?
Thank you for getting this far ¡­.
Dan. VE7CTN


 

¿ªÔÆÌåÓý

You can probably skip the drive adjustments and maybe the power output adjustments but you absolutely need to do the idle adjustment. You do need a special set up for the drive (not driver) adjustment. For power out adjustments, all you need to do is saturate the microphone with audio while adjusting the tuning dial.

?

Thank You

?

Paul W. Hansen, W6XA

Amateur Radio Service

2134 Carthage Road

Tucker, GA 30084

(864) 222-3539

www.amateurradioservice.com

?

From: [email protected] [mailto:[email protected]] On Behalf Of Dan Marriott VE7CTN
Sent: Friday, August 2, 2024 09:27
To: [email protected]
Subject: [ic7000] Driver Board Replacement, adjustments required?

?

Hello All,

I have a couple of 7ks. ?A newer one works perfectly, as far as I can tell. ?An older one has low output and the driver board is suspect. ?I intend to replace the driver board - new parts and board are on the way.?
My question: ?following the board installation, are the adjustments (as recommended by Icom) necessary or optional? ?A Service Bulletin of Feb/2010 outlines a multi step adjustment procedure requiring equipment I don¡¯t have - that¡¯s the reason for this question. ?
I want to replace the board myself, I¡¯m capable of doing that. ?But the adjustments I cannot do without purchasing equipment at expense. ?
So, ?if the adjustments are necessary, then I might just as well replace the board and send it to Icom to do the adjustments¡­ may be cheaper than buying new equipment.

Any thoughts or advice from this group?

Thank you for getting this far ¡­.

Dan. VE7CTN


 

Thanks for the feedback Paul.
Very good.
For the idle current adjustment all I need is an rf meter and an ammeter. That¡¯s ok.
For the power adjustments, when you say ¡°saturate the mic with audio¡± - white noise or whistling? Does audio frequency matter, or is it just the volume?
Thanks again.
Dan VE7CTN


 

¿ªÔÆÌåÓý

It¡¯s just volume. Whistle, say a long ¡®fiiiiiive¡¯, white noise; all good. Just drive it as hard as you can. You don¡¯t need an RF meter of any sort to set idle current.

?

Thank You

?

Paul W. Hansen, W6XA

Amateur Radio Service

2134 Carthage Road

Tucker, GA 30084

(864) 222-3539

www.amateurradioservice.com

?

From: [email protected] [mailto:[email protected]] On Behalf Of Dan Marriott VE7CTN
Sent: Friday, August 2, 2024 17:55
To: [email protected]
Subject: Re: [ic7000] Driver Board Replacement, adjustments required?

?

Thanks for the feedback Paul.

Very good.

For the idle current adjustment all I need is an rf meter and an ammeter. That¡¯s ok.

For the power adjustments, when you say ¡°saturate the mic with audio¡± - white noise or whistling? Does audio frequency matter, or is it just the volume?
Thanks again.

Dan VE7CTN


 

Thanks very much Paul.
I will give this method a try. ?
Cheers and 73
Dan VE7CTN
?