开云体育

Chris, Two issues to be aware of when using the 13-pin DIN ACC input: * The audio input on pin 11 is much more sensitive (100 mv.) than the DATA connector.? Even with good ferrite chokes on the

Hey Chris, I am using the 13-pin cable... with the West Mountain P&P.... you will be fine. Your time has value - the pre-tested cables are generally well worth the cost. On the rare occasion that I

It is probably something like the TX audio pin is not engaging the socket then. The cable works fine on my FT-817, but no joy on the FT-7000. That is why this problem was very frustrating to figure

Chris I just connected my Digirig to my IC-7000 via the 6 Pin DIN plug and it keyed up the radio just fine while using VARA HF. I monitored the audio on my HT and the audio was transmitted as well. I

You're welcome Chris. Ironically I had the opposite issue with a Signalink USB and the 13 PIN DIN plug. I had to go with the 6 PIN DIN plug. While I have both the IC-7000 and a DIgirig with both 1200

Hi In the past I have used a ZLP interface with the same 6 way cable on both the ft 817 and the ic 7000 and it worked well, Dave 2E0DMB wrote:

The radio was set correctly. My understanding is that all the radios that take the 6 pin mini DIN connectors were wired the same way. I guess not. I was able to use that port out of my SCS Pactor

I would have thought that HSEND would need to be keyed for the HF digital port to work. Perhaps the pinout on the plug is mis-connected. I used a signalink USB quite a bit with my IC-7000. I thought

Thanks, that is what I was wondering. A setting. -73 KQ6UP Thanks, Chris Maness -Sent from my iPhone

I had to set *VSEND* to On in order to use the 6 pin DIN plug for HF. In set mode, punch the *OTH* button and go to item #20. Set it to On and see if that works. 73 John Denison KD5YOU

Hi Chris, I have a older v1.5 DigiRig but the pinout at the radio end should be identical with anything. Here is a PDF diagram [ https://cloud.hamoperator.org/s/isz8ZE78ifNf6rq |

Hello, this is Chris KQ6UP.? I have my IC-7k since 2006.? This thing has taken' a licken' and it keeps on tickin'. I have some questions about the 6 pin DIN in the back.? I don't seem to be

I am going to resurrect this dead thread.? I am having the same problem here.? ?I have digirig (verified working with an FT-817).? I can RX audio no problem, but I am not getting any modulation

Hello Glen Thanks for your response. This is exactly what I'm looking for. I'll give it a go and let you know how I get on. 73s Don - M0CVZ 73s Don -

Hi Don, I have a RIGblaster PnP that I use with the 7K. In my case, I chose to use a separate USB cable for the CI-V, and then used the 13-pin cable adapter (from the RIGblaster) for the auxiliary

Good evening all I have scoured the forum but cannot find a definitive solution to my problem.... forgive me if this has already been covered and I missed it. I have a 7k and want to interface it

John N0JA, H Send is on pin 3, V Send is on pin 7. 14 volts is on pin 8. The Send line is switched by a relay between H Send and V send. However, Send is switched to ground by a single

Maybe you are expecting the circuit to do too much. I used an external device to switch my amps on my 706, similar design. Don’t know what you are doing with the send lines so no offense please.

Had the same setup installed in my 2001 dodge ram of course different animal never had any issue. Also have the 6” Hi Q and it kicks butt with my home brew back in college SS kw

Nice! Glad you figured it out. The 7000 is a great radio but they are sensitive to stray RF and low voltage. Have fun with that kW!?? ; ) 73 de KC4SM Oct 15, 2023 1:30:06 PM W1JCW