开云体育

Slave port: Kenwood commands to control an amplifier

Alec SP2EWQ All Messages By This Member #97953 Hi, I have been trying, still unsuccessfully, to make my amplifier follow TRX band changes using Loggr32's Slave Port and Kenwood commands. My slave port configuration Slave debug window shows the following commands upon band changes to which the amp stays unresponsive However, using a Kenwood command simulator to which the amplifier responds correctly,? I can see the following communication on the port?where, in the box,? You can find the moment when the amp switched from 10m to 15m band) Will You help, please? Best regards, Alec
Bob All Messages By This Member #97955 The problem is possibly/probably caused by Logger32 sending a FR0; command to select VFO-A before the FA xxx; frequency command. SeventyThree(s). toggle quoted message Show quoted text On 04/08/2025 10:53 AM EDT Alec SP2EWQ via groups.io <aleksander.otulak@...> wrote: ? ? ? Hi, ? I have been trying, still unsuccessfully, to make my amplifier follow TRX band changes using Loggr32's Slave Port and Kenwood commands. ? My slave port configuration ? Slave debug window shows the following commands upon band changes to which the amp stays unresponsive ? ? However, using a Kenwood command simulator to which the amplifier responds correctly,? I can see the following communication on the port?where, in the box,? You can find the moment when the amp switched from 10m to 15m band) ? Will You help, please? ? Best regards, Alec ? ? ? ?
Alec SP2EWQ All Messages By This Member #97956 Bob, please, any chance to rectify that? Please... Best regards, Alec ------ Wiadomo?? oryginalna ------ Nadawca "Bob via groups.io" <k4cy@...> Do [email protected] Data 08.04.2025 17:58:17 Temat Re: [hamlogger] Slave port: Kenwood commands to control an amplifier toggle quoted message Show quoted text The problem is possibly/probably caused by Logger32 sending a FR0; command to select VFO-A before the FA xxx; frequency command. SeventyThree(s). On 04/08/2025 10:53 AM EDT Alec SP2EWQ via groups.io <aleksander.otulak@...> wrote: ? ? ? Hi, ? I have been trying, still unsuccessfully, to make my amplifier follow TRX band changes using Loggr32's Slave Port and Kenwood commands. ? My slave port configuration ? Slave debug window shows the following commands upon band changes to which the amp stays unresponsive ? ? However, using a Kenwood command simulator to which the amplifier responds correctly,? I can see the following communication on the port?where, in the box,? You can find the moment when the amp switched from 10m to 15m band) ? Will You help, please? ? Best regards, Alec ? ? ? ?
Bob All Messages By This Member #97957 I could remove the FR0; but I have no idea how that will impact other users of the slave port with different devices connected (for example another Kenwood radio). SeventyThree(s). toggle quoted message Show quoted text On 04/08/2025 12:03 PM EDT Alec SP2EWQ via groups.io <aleksander.otulak@...> wrote: ? ? ? ? Bob, ? please, any chance to rectify that? ? Please... Best regards, Alec ? ? ------ Wiadomo?? oryginalna ------ Nadawca "Bob via groups.io" <k4cy@...> Do [email protected] Data 08.04.2025 17:58:17 Temat Re: [hamlogger] Slave port: Kenwood commands to control an amplifier ? The problem is possibly/probably caused by Logger32 sending a FR0; command to select VFO-A before the FA xxx; frequency command. SeventyThree(s). On 04/08/2025 10:53 AM EDT Alec SP2EWQ via groups.io <aleksander.otulak@...> wrote: ? ? ? Hi, ? I have been trying, still unsuccessfully, to make my amplifier follow TRX band changes using Loggr32's Slave Port and Kenwood commands. ? My slave port configuration ? Slave debug window shows the following commands upon band changes to which the amp stays unresponsive ? ? However, using a Kenwood command simulator to which the amplifier responds correctly,? I can see the following communication on the port?where, in the box,? You can find the moment when the amp switched from 10m to 15m band) ? Will You help, please? ? Best regards, Alec ? ? ? ? ? ?
n5kd All Messages By This Member #97958 开云体育 Is it something to do with the slave setup set to "Slave follows VFO A only" On 4/8/2025 15:58, Bob via groups.io wrote: toggle quoted message Show quoted text The problem is possibly/probably caused by Logger32 sending a FR0; command to select VFO-A before the FA xxx; frequency command. SeventyThree(s). On 04/08/2025 10:53 AM EDT Alec SP2EWQ via groups.io <aleksander.otulak@...> wrote: ? ? ? Hi, ? I have been trying, still unsuccessfully, to make my amplifier follow TRX band changes using Loggr32's Slave Port and Kenwood commands. ? My slave port configuration ? Slave debug window shows the following commands upon band changes to which the amp stays unresponsive ? ? However, using a Kenwood command simulator to which the amplifier responds correctly,? I can see the following communication on the port?where, in the box,? You can find the moment when the amp switched from 10m to 15m band) ? Will You help, please? ? Best regards, Alec ? ? ? ?
Alec SP2EWQ All Messages By This Member #97959 Bob, one can have that box unclicked. Thus the command wouldn't point to any particular VFO, please... Best regards, Alec ------ Wiadomo?? oryginalna ------ Nadawca "Bob via groups.io" <k4cy@...> Do [email protected]; "Alec SP2EWQ via groups.io" <aleksander.otulak@...> Data 08.04.2025 18:15:05 Temat Re: [hamlogger] Slave port: Kenwood commands to control an amplifier toggle quoted message Show quoted text I could remove the FR0; but I have no idea how that will impact other users of the slave port with different devices connected (for example another Kenwood radio). SeventyThree(s). On 04/08/2025 12:03 PM EDT Alec SP2EWQ via groups.io <aleksander.otulak@...> wrote: ? ? ? ? Bob, ? please, any chance to rectify that? ? Please... Best regards, Alec ? ? ------ Wiadomo?? oryginalna ------ Nadawca "Bob via groups.io" <k4cy@...> Do [email protected] Data 08.04.2025 17:58:17 Temat Re: [hamlogger] Slave port: Kenwood commands to control an amplifier ? The problem is possibly/probably caused by Logger32 sending a FR0; command to select VFO-A before the FA xxx; frequency command. SeventyThree(s). On 04/08/2025 10:53 AM EDT Alec SP2EWQ via groups.io <aleksander.otulak@...> wrote: ? ? ? Hi, ? I have been trying, still unsuccessfully, to make my amplifier follow TRX band changes using Loggr32's Slave Port and Kenwood commands. ? My slave port configuration ? Slave debug window shows the following commands upon band changes to which the amp stays unresponsive ? ? However, using a Kenwood command simulator to which the amplifier responds correctly,? I can see the following communication on the port?where, in the box,? You can find the moment when the amp switched from 10m to 15m band) ? Will You help, please? ? Best regards, Alec ? ? ? ? ? ?

Previous Topic Next Topic