开云体育

Hi Herve Here is the updated User Guide with COM16 as the COM port, ie as per the installer. 73 Peter - GM8JCF

Hi Herve Have you followed the instructions from /g/g8jcfsdr/attachment/269/0/G8JCFSDRUserGuide_284_Linux.pdf which describes how to use LINUX USB Serial ports within the WINE

Hi Herve Thank You for trying out Build 284. It's been quite a few months since I last used the G8JCFSDR on LINUX, so my memory is a bit "faint" unfortunately. The G8JCFSDR configuration is stored

Hello Peter, I am using wine-5.0 (Ubuntu 5.0-3ubuntu1) on Linux Mint 20.2 Cinnamon 5.0.7 with 5.13.0-27-generic. There is some problem with the com port when you plug/unplug arduino board. You have

Hi I have been working with Adrian Cole from Australia, (many thanks to Adrian for his patience and detailed feedback), to get the G8JCFSDR working once again with XP, and also to make installing the

Hi Yoyos I must repeat that you have nothing to apologise for. You have set in train some thinking that perhaps I should set some of the digital outputs high for each frequency range to enable

Hi, Peter - GM8JCF Thank you for your information. I originally planned to improve the selectivity and sensitivity on the Elektor SDR Shield 2.0 front-end. But for now I'm quite satisfied, using a

Hi Yoyos There is no need to apologise to me, you were trying to do something quite reasonable, and have done nothing wrong as far as I know. si5351vfo2_1_G8GCFSDR_jmP.ino has got nothing to do with

Hi, Jean-Marc Paratte and Peter - GM8JCF Thank you for your response. I apologize for changing si5351vfo2_1_G8GCFSDR_jmP.ino and using G8JCFSDR.exe incorrectly. I did this because I wanted to use

Hi Yoyos The G8JCFSDR software comes complete with the required firmware for the Arduino UNO. What are you trying to achieve by writing your own firmware ? The firmware is very tightly coupled with

Hi, I wrote si5351vfo2_1_G8GCFSDR_jmP.ino for G8JCFSDR v280. After that, Peter changed/completed the Arduino exchange protocol. It could be a good idea if Peter will publish the source of the Arduino

Hi, All My Elector SDR Shield 2.0 arrived safely, thanks to Elektor International media BV. Based on firmware si5351vfo2_1_G8GCFSDR_jmP.ino I wrote G8JCFSDR_Elector.ino to control the Arduino

Hi I checked the XONAR U7 manual, (I know I should have RTFM in the first place !!) and the specifications say that the 3dB frequency response is 10-46KHz, so the spectrum displayed agrees with the

Hi I started up my PMSDR, and ran the G8JCFSDR at 192KHz - a really fine I/Q SDR. The PMSDR also looks pretty flat to about 48KHz, and rolls off after that, but the roll-off doesn't look anywhere as

Hi I thought I would post a screen-grab of the G8JCFSDR running with 192 KHz sampling rate. I am using an ASUS XONAR U7. You can see that the U7's bandwidth is pretty flat upto about 48KHz and then

Hi As you saw last night I upgraded the G8JCFSDR website to use HTTPS, and I could do with some further help testing it please. On the main page there is a link to a contact page, " This is Peter

Hi Erwin I just edited this page and it should be OK now (I hope!!) Peter Hi Erwin I just checked that page using Edge, and the images are not from a secure page, ie they use http rather than

Thank U Michael

Thank U Ralf

Hi Peter, all is working well. Config. Win10, Firefox 92.0 / 64. Greetings Ralf - DK9PS - Gesendet: Montag, 13. September 2021 um 03:43 Uhr Von: "G8JCF"