开云体育

T-nut for the sliding table

James Zhu All Messages By This Member #121508 I had a custom shop make some steel t-nuts a few years ago after I got?my?KF700sp. Today, I found that I have extra 2 short t-nuts and 3 long t-nuts laying around unused. I use it with Kreg automaxx clamps, see pictures below. As I mentioned before, the automaxx clamp pulls the stock a bit when clamping it. As long as you have the plywood block placed against the stock being clamped, the stock will not move at all. The short one is 70mm long, the long one is 120mm. All have 5/16"-18 thread. I can offer it ($25 for short one, $40 for long one, plus shipping), I am in Ontario, Canada. I can get the shipping quote from Canada Post or your choice of carrier like Fedex and UPS. I heard the shipping cost from Canada Post is cheaper than Fedex and UPS here. If you are interested, send me a private email. James
Wade Dees All Messages By This Member #121535 开云体育 Are the T-slot grooves the same in a K700S? ?I’d measure mine off the dimensions you sent, but I’m currently out of town. Headed back tomorrow though. ?I’d be interested! Thx, Wade toggle quoted message Show quoted text On Feb 17, 2022, at 12:52 PM, James Zhu <james.zhu2@...> wrote: ? I had a custom shop make some steel t-nuts a few years ago after I got?my?KF700sp. Today, I found that I have extra 2 short t-nuts and 3 long t-nuts laying around unused. I use it with Kreg automaxx clamps, see pictures below. As I mentioned before, the automaxx clamp pulls the stock a bit when clamping it. As long as you have the plywood block placed against the stock being clamped, the stock will not move at all. The short one is 70mm long, the long one is 120mm. All have 5/16"-18 thread. I can offer it ($25 for short one, $40 for long one, plus shipping), I am in Ontario, Canada. I can get the shipping quote from Canada Post or your choice of carrier like Fedex and UPS. I heard the shipping cost from Canada Post is cheaper than Fedex and UPS here. If you are interested, send me a private email. James
David P. Best All Messages By This Member #121537 开云体育 All X-Roll sliding tables on?the -500, -700, -900, and Kappa 400 machines?are made from the same aluminum extrusion (just different lengths), and thus the T-slots are identical. ?The Hammer and -550/590 series sliding tables differ from the aforementioned models.? David Best - Sent from my iPad toggle quoted message Show quoted text On Feb 17, 2022, at 8:14 PM, Wade Dees <wjdsignature@...> wrote: ? Are the T-slot grooves the same in a K700S? ?I’d measure mine off the dimensions you sent, but I’m currently out of town. Headed back tomorrow though. ?I’d be interested! Thx, Wade On Feb 17, 2022, at 12:52 PM, James Zhu <james.zhu2@...> wrote: ? I had a custom shop make some steel t-nuts a few years ago after I got?my?KF700sp. Today, I found that I have extra 2 short t-nuts and 3 long t-nuts laying around unused. I use it with Kreg automaxx clamps, see pictures below. As I mentioned before, the automaxx clamp pulls the stock a bit when clamping it. As long as you have the plywood block placed against the stock being clamped, the stock will not move at all. The short one is 70mm long, the long one is 120mm. All have 5/16"-18 thread. I can offer it ($25 for short one, $40 for long one, plus shipping), I am in Ontario, Canada. I can get the shipping quote from Canada Post or your choice of carrier like Fedex and UPS. I heard the shipping cost from Canada Post is cheaper than Fedex and UPS here. If you are interested, send me a private email. James
imran All Messages By This Member #121552 开云体育 ?If you use the flat bar stock, 1/2”x1 1/4” (I used CR1018), it will fit Xroll but would require?a small radius on the two bottom long sides for?the pre Xroll Felder table, like my 2002 KF700. I did that with a grinder, does not take much time. Imran? toggle quoted message Show quoted text On Feb 17, 2022, at 11:28 PM, david@... via groups.io <david@...> wrote: ?All X-Roll sliding tables on?the -500, -700, -900, and Kappa 400 machines?are made from the same aluminum extrusion (just different lengths), and thus the T-slots are identical. ?The Hammer and -550/590 series sliding tables differ from the aforementioned models.? David Best - Sent from my iPad On Feb 17, 2022, at 8:14 PM, Wade Dees <wjdsignature@...> wrote: ? Are the T-slot grooves the same in a K700S? ?I’d measure mine off the dimensions you sent, but I’m currently out of town. Headed back tomorrow though. ?I’d be interested! Thx, Wade On Feb 17, 2022, at 12:52 PM, James Zhu <james.zhu2@...> wrote: ? I had a custom shop make some steel t-nuts a few years ago after I got?my?KF700sp. Today, I found that I have extra 2 short t-nuts and 3 long t-nuts laying around unused. I use it with Kreg automaxx clamps, see pictures below. As I mentioned before, the automaxx clamp pulls the stock a bit when clamping it. As long as you have the plywood block placed against the stock being clamped, the stock will not move at all. The short one is 70mm long, the long one is 120mm. All have 5/16"-18 thread. I can offer it ($25 for short one, $40 for long one, plus shipping), I am in Ontario, Canada. I can get the shipping quote from Canada Post or your choice of carrier like Fedex and UPS. I heard the shipping cost from Canada Post is cheaper than Fedex and UPS here. If you are interested, send me a private email. James
Mike All Messages By This Member #121561 Two weeks ago, I would have bought these for my Kreg clamps. In the meantime, I made some from a piece of 170-year-old oak and Tee nuts. The only problem I had was the oak was too hard for the tee nuts, causing them to deform. I had to pre-drill holes for the spurs. Hopefully, these will work for another 170 years.

Previous Topic Next Topic