On Mar 3, 2021, at 3:56 PM, andrew.mackinnon88@... wrote:

Hi, I am looking to order a k 700 s this week.
where I am at the moment I only have single phase. Does anyone have experience with this saw with felders 3kw single phase motor? I am worried it might not have enough power. My other option is to get the 5.5kw and run a rotary phase converter.

Any information would be much appreciated.

regards

Andrew

On Mar 3, 2021, at 4:15 PM, Michael Todrin <michaeltodrin@...> wrote:

?Andrew,

I have a 3kw kf 700 and ripping and crosscutting to 8/4 has been no problem. ?Crosscutting to 12/4 has been fine too. ?I imagine long rips of 12/4 ?might give it trouble but in two years have found the 3kw to be fine. ?

Enjoy your new saw.

Michael

On Mar 3, 2021, at 3:56 PM, andrew.mackinnon88@... wrote:

Hi, I am looking to order a k 700 s this week.
where I am at the moment I only have single phase. Does anyone have experience with this saw with felders 3kw single phase motor? I am worried it might not have enough power. My other option is to get the 5.5kw and run a rotary phase converter.

Any information would be much appreciated.

regards

Andrew

Lucky

On 4 Mar 2021, at 8:26 am, Philip Davidson <pgdiv4@...> wrote:

I have an older Kf 700 pro single phase and just ripped 12/4 mahogany board 18 inches wide and 12 feet long. ?Slow the feed when you hear it working hard but the rip blade of 24 teeth works through it. ?I’ve cut thicker stock but not often.<image1.jpeg>

Philip Davidson?

On Mar 3, 2021, at 4:15 PM, Michael Todrin <michaeltodrin@...> wrote:

?Andrew,

I have a 3kw kf 700 and ripping and crosscutting to 8/4 has been no problem. ?Crosscutting to 12/4 has been fine too. ?I imagine long rips of 12/4 ?might give it trouble but in two years have found the 3kw to be fine. ?

Enjoy your new saw.

Michael

On Mar 3, 2021, at 3:56 PM, andrew.mackinnon88@... wrote:

Hi, I am looking to order a k 700 s this week.
where I am at the moment I only have single phase. Does anyone have experience with this saw with felders 3kw single phase motor? I am worried it might not have enough power. My other option is to get the 5.5kw and run a rotary phase converter.

Any information would be much appreciated.

regards

Andrew

--
Philip

On Mar 3, 2021, at 5:40 PM, David Luckensmeyer <dhluckens@...> wrote:

?Wow. The photo says it all. Nice wood!

Lucky

On 4 Mar 2021, at 8:26 am, Philip Davidson <pgdiv4@...> wrote:

I have an older Kf 700 pro single phase and just ripped 12/4 mahogany board 18 inches wide and 12 feet long. ?Slow the feed when you hear it working hard but the rip blade of 24 teeth works through it. ?I’ve cut thicker stock but not often.<image1.jpeg>

Philip Davidson?

On Mar 3, 2021, at 4:15 PM, Michael Todrin <michaeltodrin@...> wrote:

?Andrew,

I have a 3kw kf 700 and ripping and crosscutting to 8/4 has been no problem. ?Crosscutting to 12/4 has been fine too. ?I imagine long rips of 12/4 ?might give it trouble but in two years have found the 3kw to be fine. ?

Enjoy your new saw.

Michael

On Mar 3, 2021, at 3:56 PM, andrew.mackinnon88@... wrote:

Hi, I am looking to order a k 700 s this week.
where I am at the moment I only have single phase. Does anyone have experience with this saw with felders 3kw single phase motor? I am worried it might not have enough power. My other option is to get the 5.5kw and run a rotary phase converter.

Any information would be much appreciated.

regards

Andrew

--
Philip

On Mar 3, 2021, at 6:49 PM, Philip Davidson <pgdiv4@...> wrote:

?This was a convenient purchase that will cover a pencil post bed and guitar and ukulele necks. ?

Philip Davidson?

On Mar 3, 2021, at 5:40 PM, David Luckensmeyer <dhluckens@...> wrote:

?Wow. The photo says it all. Nice wood!

Lucky

On 4 Mar 2021, at 8:26 am, Philip Davidson <pgdiv4@...> wrote:

I have an older Kf 700 pro single phase and just ripped 12/4 mahogany board 18 inches wide and 12 feet long. ?Slow the feed when you hear it working hard but the rip blade of 24 teeth works through it. ?I’ve cut thicker stock but not often.<image1.jpeg>

Philip Davidson?

On Mar 3, 2021, at 4:15 PM, Michael Todrin <michaeltodrin@...> wrote:

?Andrew,

I have a 3kw kf 700 and ripping and crosscutting to 8/4 has been no problem. ?Crosscutting to 12/4 has been fine too. ?I imagine long rips of 12/4 ?might give it trouble but in two years have found the 3kw to be fine. ?

Enjoy your new saw.

Michael

On Mar 3, 2021, at 3:56 PM, andrew.mackinnon88@... wrote:

Hi, I am looking to order a k 700 s this week.
where I am at the moment I only have single phase. Does anyone have experience with this saw with felders 3kw single phase motor? I am worried it might not have enough power. My other option is to get the 5.5kw and run a rotary phase converter.

Any information would be much appreciated.

regards

Andrew

--
Philip

--
Philip
davidsonukuleles.com