开云体育

AIGNER FLUSHFIX

mac campshure All Messages By This Member #102062 开云体育 Like I mentioned earlier I have the Hebor / Alder since 1990 ihave 240 volt unit ?simple and heavy duty same as Hoffman today. martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330?cell 608-824-0023?fax airtightclamps@... Designing and building for 47 years toggle quoted message Show quoted text On Feb 17, 2020, at 1:52 PM, Michael Todrin <michaeltodrin@...> wrote: ?Does anyone have any experience with the Hoffman lipping planer? Michael
Jason Holtz All Messages By This Member #102065 I've used the Hoffmann, sold here in the US as Adler if I'm not mistaken. It's a good tool, also expensive. I have the Virutex and it's quite good despite being half the cost of it's competitors. My shop made offset base for a Bosch Colt still gets a surprising amount use as well does my Veritas low angle block plane. If I've just got a few pieces to trim, the plane is always my go to. Jason Holtz J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406 612 432-2765 -- Jason J. Holtz Furniture 3307 Snelling Ave. South Minneapolis, MN 55406
Michael Todrin All Messages By This Member #102076 开云体育 Thanks. I did not realize it was being sold under another name here.? toggle quoted message Show quoted text On Feb 17, 2020, at 6:46 PM, mac campshure <mac512002@...> wrote: ?Like I mentioned earlier I have the Hebor / Alder since 1990 ihave 240 volt unit ?simple and heavy duty same as Hoffman today. martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330?cell 608-824-0023?fax airtightclamps@... Designing and building for 47 years On Feb 17, 2020, at 1:52 PM, Michael Todrin <michaeltodrin@...> wrote: ?Does anyone have any experience with the Hoffman lipping planer? Michael
Tom Gensmer All Messages By This Member #102383 Resurrecting this thread, for trimming thicker, solid wood edge banding I completely forgot to mention the Betterly flush trim router setup:?? This setup will trim up to 1-1/2" wide edge lipping in a single pass.? Betterly is based in Minnesota, ~20 minutes North of Minneapolis. They specialize in making custom router bases, primarily catering to the various counter top trades (laminate, solid surface). They perform all of their milling/machining in-house.? -- Tom Gensmer Heritage Home Renewals, LLC Minneapolis, MN
habacomike (Mike King) All Messages By This Member #102394 开云体育 That’s pretty pricey. ?I made a similar rig from MDF with a trailer hitch ball for a handle based on a design from Michael Fortune. ?I believe it is maybe $15 in materials. toggle quoted message Show quoted text On Feb 25, 2020, at 6:43 AM, tom@... wrote: Resurrecting this thread, for trimming thicker, solid wood edge banding I completely forgot to mention the Betterly flush trim router setup:?? This setup will trim up to 1-1/2" wide edge lipping in a single pass.? Betterly is based in Minnesota, ~20 minutes North of Minneapolis. They specialize in making custom router bases, primarily catering to the various counter top trades (laminate, solid surface). They perform all of their milling/machining in-house.? -- Tom Gensmer Heritage Home Renewals, LLC Minneapolis, MN
p_shapiro All Messages By This Member #102427 The system I used when I had miles of edging to flush up was a variation on the Aigner and cost very little. I cut a piece of 1/2” ply to fit the top of the shaper and held it back from the fence by a distance slightly more than the thickness of the banding. I then set up a straight shaper cutter to a few thousandths less than the thickness of the ply and used my power feeder to run the workpiece past the cutter head in climb-feed mode, to reduce chip-out to virtually nothing. A couple of cleats applied to the bottom of the ply and registering against the edges of the shaper top kept the ply securely in position. A few passes with a finish sander took care of the final flushing. ?Worked great.?

Previous Topic Next Topic