3/8” Padded Swivel #machinemount #machinelevelingfeet
开云体育Mark, part in the link you posted is not padded. I have it on my KF and is fine but I thought padded is a good idea. Most padded ones I found were 2x or 3x so that is why I posted. Imran On Jan 10, 2020, at 1:15 PM, mark thomas <murkyd@...> wrote: ? It's 5% less at McMaster: On Fri, Jan 10, 2020 at 7:20 AM imranindiana via Groups.Io <imranindiana=[email protected]> wrote:
|
开云体育Hi Randy, I am not sure if 10mm is universally the hole size on Felder machines but it is for my KF and K975. I am kicking myself for not thinking of ordering a set for Dual51. Obviously, I have not checked the hole size for Dual51. As Mark posted McMaster is another source, in case you need to add other items to the order. Imran On Jan 10, 2020, at 7:50 PM, Randy Child via Groups.Io <strongman_one@...> wrote: ? is the thread size the correct size for our K975 saw's?? If so, I'm gonna get some too .. LOL
On Friday, January 10, 2020, 07:20:42 AM PST, imranindiana via Groups.Io <imranindiana@...> wrote:
Found these for my K975. I do not recall paying so little. Ground shipping was $5 at Zoro: Imran |
|
10mm seems awfully small for threads for feet to hold a 2000lb saw. But I think there's a welded nut on the inside if I'm not mistaken..? I'm considering getting Zambus casters.. Have you seen those?
On Friday, January 10, 2020, 06:23:19 PM PST, imranindiana via Groups.Io <imranindiana@...> wrote:
Hi Randy, I am not sure if 10mm is universally the hole size on Felder machines but it is for my KF and K975. I am kicking myself for not thinking of ordering a set for Dual51. Obviously, I have not checked the hole size for Dual51. As Mark posted McMaster is another source, in case you need to add other items to the order. Imran On Jan 10, 2020, at 7:50 PM, Randy Child via Groups.Io <strongman_one@...> wrote: ? is the thread size the correct size for our K975 saw's?? If so, I'm gonna get some too .. LOL
On Friday, January 10, 2020, 07:20:42 AM PST, imranindiana via Groups.Io <imranindiana@...> wrote:
Found these for my K975. I do not recall paying so little. Ground shipping was $5 at Zoro: Imran |
开云体育Randy, I have heard of them here. Recall people like them. The 3/8” can support over 10000# so I am not concerned. However, if you need to move the machine then casters may be the way to go. Although, I find it much much easier to move with a pallet jack than spinning the wheels on this type of caster. Here is a link from SMC with some lower cost options than Zambus. With the new shop layout necessitated by the addition of K975, I need to put casters on my assembly bench. Anyhow, I am looking for some solution there but best would be to use the PJ. For that I would need to redo the base it sits on. Imran On Jan 11, 2020, at 7:30 AM, Randy Child via Groups.Io <strongman_one@...> wrote: ? 10mm seems awfully small for threads for feet to hold a 2000lb saw. But I think there's a welded nut on the inside if I'm not mistaken..? I'm considering getting Zambus casters.. Have you seen those?
On Friday, January 10, 2020, 06:23:19 PM PST, imranindiana via Groups.Io <imranindiana@...> wrote:
Hi Randy, I am not sure if 10mm is universally the hole size on Felder machines but it is for my KF and K975. I am kicking myself for not thinking of ordering a set for Dual51. Obviously, I have not checked the hole size for Dual51. As Mark posted McMaster is another source, in case you need to add other items to the order. Imran On Jan 10, 2020, at 7:50 PM, Randy Child via Groups.Io <strongman_one@...> wrote: ? is the thread size the correct size for our K975 saw's?? If so, I'm gonna get some too .. LOL
On Friday, January 10, 2020, 07:20:42 AM PST, imranindiana via Groups.Io <imranindiana@...> wrote:
Found these for my K975. I do not recall paying so little. Ground shipping was $5 at Zoro: Imran <Screenshot_20200111-042855_Amazon Shopping.jpg> |
开云体育Randy, I forgot to add that the long base under the slider of my older K975 has round threaded plates that allow very small (irregular floor) amount of leveling. The other 2 ends only have holes to attach a foot or caster. Imran On Jan 11, 2020, at 10:37 AM, Brian Lamb <bklamb1@...> wrote: ?
I have these on a drum sander, wouldn't put them on something heavy like a saw, too hard to control the ?direction it wants to go.
=============== Brian Lamb blamb11@... Phoenix, AZ ===============
From: [email protected] <[email protected]> on behalf of Randy Child via Groups.Io <strongman_one@...>
Sent: Saturday, January 11, 2020 5:30 AM To: [email protected] <[email protected]> Subject: Re: [FOG] 3/8” Padded Swivel #MachineLevelingFeet #MachineMount ?
10mm seems awfully small for threads for feet to hold a 2000lb saw. But I think there's a welded nut on the inside if I'm not mistaken..? I'm considering getting Zambus casters.. Have you seen those?
On Friday, January 10, 2020, 06:23:19 PM PST, imranindiana via Groups.Io <imranindiana@...> wrote:
Hi Randy,
I am not sure if 10mm is universally the hole size on Felder machines but it is for my KF and K975. I am kicking myself for not thinking of ordering a set for Dual51. Obviously, I have not checked the hole size for Dual51.
As Mark posted McMaster is another source, in case you need to add other items to the order.
Imran
On Jan 10, 2020, at 7:50 PM, Randy Child via Groups.Io <strongman_one@...> wrote: ?
is the thread size the correct size for our K975 saw's?? If so, I'm gonna get some too .. LOL
On Friday, January 10, 2020, 07:20:42 AM PST, imranindiana via Groups.Io <imranindiana@...> wrote:
Found these for my K975. I do not recall paying so little. Ground shipping was $5 at Zoro:
Imran
-- Brian Lamb blamb11@...? ? |
imran
