|
I have been teasing about this for over a year now. Finally have it printed and final tweaks are being made. I intend to have it available for purchase beginning of next year. There is one for the rip fence as well. The idea is to supply a complete system with DRO to make installation easy.
|
Looks great Imran! Bill Belanger?
toggle quoted message
Show quoted text
On Dec 15, 2024, at 06:48, imranindiana via groups.io <imranindiana@...> wrote:
? I have been teasing about this for over a year now. Finally have it printed and final tweaks are being made. I intend to have it available for purchase beginning of next year. There is one for the rip fence as well. The idea is to supply a complete system with DRO to make installation easy.
<Video.mov>
|
Hi Imran, nice support for the Dro M503, really compliments. It would be nice if you could also design one for the cross guide stops (like the ones in the photo) of my Minimax SC4 Elite, unfortunately I'm not good at 3d drawing.
?
?
|
Thanks Bill.
Hi Andrea,
Puoi rispondere in privato cliccando su "Rispondi al mittente" in fondo al messaggio. Inviami una foto del tuo fermo guida trasversale su minimax con alcune dimensioni. Posso controllare se questo design si adatta. Avrei anche bisogno della larghezza della fessura della recinzione e della profondità.
toggle quoted message
Show quoted text
On Dec 15, 2024, at 11:45?AM, Andrea Cerroni via groups.io <andreacerroni75@...> wrote: ? Ciao Imran, bel supporto per il Dro M503, complimenti davvero. Sarebbe bello se potessi anche progettarne uno per i fermi guida incrociati del mio minimax sc4 elite, sfortunatamente non sono bravo nel disegno 3D.
?
?
<Screenshot_2021-03-27-16-26-34-035_com.google.android.youtube.jpg>
|
Andrea, Thanks for the picture. There is not much body to attach the DRO. The option I see is to use a longer axle for the flip stop and attach a simple box with DRO in it.
For the sensor you need a minimum slot width of 10mm. The sensor holder in my design requires 12mm. If the slits are not wide enough then you may have to apply mag tape on the rear of the fence, assuming you don’t use that side of the fence. If you do that then you will need to make a simple bracket to hold sensor in front of the tape.
Hope this helps.
toggle quoted message
Show quoted text
On Dec 15, 2024, at 12:07?PM, Andrea Cerroni via groups.io <andreacerroni75@...> wrote: ? [Edited Message Follows]
Hi Imran, nice support for the Dro M503, really compliments. It would be nice if you could also design one for the cross guide stops (like the ones in the photo) of my Minimax SC4 Elite, unfortunately I'm not good at 3d drawing.
?
?
<Screenshot_2021-03-27-16-26-34-035_com.google.android.youtube.jpg>
|
Ok, thank you Malik, I'll see what to do
|
That's awesome Imran,
I have been looking at the DRO on my flipstop myself lately thinking of ways i can make it better. Not sure i would ever get it looking that professional though!
Regards,
Bryce
--
https://www.brycecomerwoodworks.com/
https://www.youtube.com/channel/UCHdrRaAZd_pOa7wwbdNPUEw
|
toggle quoted message
Show quoted text
On Dec 15, 2024, at 2:26?PM, Bryce Comer via groups.io <bryce@...> wrote: ? That's awesome Imran,
I have been looking at the DRO on my flipstop myself lately thinking of ways i can make it better. Not sure i would ever get it looking that professional though!
Regards,
Bryce
--
https://www.brycecomerwoodworks.com/
https://www.youtube.com/channel/UCHdrRaAZd_pOa7wwbdNPUEw
|
Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
toggle quoted message
Show quoted text
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
I just went to the Proscale website and noticed this for Felder K700 with 1800mm crosscut fence:
? --Tim
On Sun, Dec 15, 2024 at 5:36?PM Wade Dees via <wjdsignature= [email protected]> wrote: Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
I expect to offer my version for less than 1/3 of that.
toggle quoted message
Show quoted text
On Dec 15, 2024, at 8:27?PM, Tim Prinzing via groups.io <tim.prinzing@...> wrote: ? I just went to the Proscale website and noticed this for Felder K700 with 1800mm crosscut fence:
? --Tim On Sun, Dec 15, 2024 at 5:36?PM Wade Dees via <wjdsignature= [email protected]> wrote: Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
Yours looks nice, and that would be a great price point! ? --Tim
On Sun, Dec 15, 2024 at 7:40?PM imranindiana via <imranindiana= [email protected]> wrote: I expect to offer my version for less than 1/3 of that. On Dec 15, 2024, at 8:27?PM, Tim Prinzing via <tim.prinzing= [email protected]> wrote: ? I just went to the Proscale website and noticed this for Felder K700 with 1800mm crosscut fence:
? --Tim On Sun, Dec 15, 2024 at 5:36?PM Wade Dees via <wjdsignature= [email protected]> wrote: Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
Thanks Aaron, I had already seen the proscale kit. I am looking for a solution to adapt the Dro M503 that I bought, and I will certainly take inspiration from this kit to create a functional support with a nice look like Malik's
|
Hi Tim,
My apologies, I should have mentioned, I’m hoping for one that fits the rip fence of the K700S.
Thx,
Wade
toggle quoted message
Show quoted text
On Dec 15, 2024, at 5:28?PM, Tim Prinzing via groups.io <tim.prinzing@...> wrote:
? I just went to the Proscale website and noticed this for Felder K700 with 1800mm crosscut fence:
? --Tim On Sun, Dec 15, 2024 at 5:36?PM Wade Dees via <wjdsignature= [email protected]> wrote: Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
Hi Wade,
If you want a high quality rip fence DRO, I would choose Fiama F8P. I plan to have this available where one does not need to fabricate the bracket as shown in the doc below. It allows quick display update when fence profile is changed between hi an lo whereas M503 requires recalibration.
toggle quoted message
Show quoted text
On Dec 16, 2024, at 7:47?AM, Wade Dees via groups.io <wjdsignature@...> wrote: ? Hi Tim,
My apologies, I should have mentioned, I’m hoping for one that fits the rip fence of the K700S.
Thx,
Wade
On Dec 15, 2024, at 5:28?PM, Tim Prinzing via groups.io <tim.prinzing@...> wrote:
? I just went to the Proscale website and noticed this for Felder K700 with 1800mm crosscut fence:
? --Tim On Sun, Dec 15, 2024 at 5:36?PM Wade Dees via <wjdsignature= [email protected]> wrote: Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
Hi Imran,
For some reason I cannot open the link. ?
Wade
toggle quoted message
Show quoted text
On Dec 16, 2024, at 5:44?AM, imranindiana via groups.io <imranindiana@...> wrote:
? Hi Wade,
If you want a high quality rip fence DRO, I would choose Fiama F8P. I plan to have this available where one does not need to fabricate the bracket as shown in the doc below. It allows quick display update when fence profile is changed between hi an lo whereas M503 requires recalibration.
On Dec 16, 2024, at 7:47?AM, Wade Dees via groups.io <wjdsignature@...> wrote:
? Hi Tim,
My apologies, I should have mentioned, I’m hoping for one that fits the rip fence of the K700S.
Thx,
Wade
On Dec 15, 2024, at 5:28?PM, Tim Prinzing via groups.io <tim.prinzing@...> wrote:
? I just went to the Proscale website and noticed this for Felder K700 with 1800mm crosscut fence:
? --Tim On Sun, Dec 15, 2024 at 5:36?PM Wade Dees via <wjdsignature= [email protected]> wrote: Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
You guys do realize that Proscale or Imran's contraption do nothing to get rid of the crappy flipstop that Felder uses and isn't square. I am also not sure I would want to trust the flimsy 3D printed brackets that I'm seeing here to hold the electronics. One good bump with a board will have the units in multiple pieces... of course if the STL is provided you can always print another, consider it a consumable.
Brian Lamb blamb11@... lambtoolworks.com
On Sunday, December 15, 2024 at 06:27:50 PM MST, Tim Prinzing via groups.io <tim.prinzing@...> wrote:
I just went to the Proscale website and noticed this for Felder K700 with 1800mm crosscut fence:
? --Tim
On Sun, Dec 15, 2024 at 5:36?PM Wade Dees via <wjdsignature= [email protected]> wrote: Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
Wade,
Not sure why it works for me, anyways, here is a copy.
toggle quoted message
Show quoted text
On Dec 16, 2024, at 10:02?AM, Wade Dees via groups.io <wjdsignature@...> wrote: ? Hi Imran,
For some reason I cannot open the link. ?
Wade On Dec 16, 2024, at 5:44?AM, imranindiana via groups.io <imranindiana@...> wrote:
? Hi Wade,
If you want a high quality rip fence DRO, I would choose Fiama F8P. I plan to have this available where one does not need to fabricate the bracket as shown in the doc below. It allows quick display update when fence profile is changed between hi an lo whereas M503 requires recalibration.
On Dec 16, 2024, at 7:47?AM, Wade Dees via groups.io <wjdsignature@...> wrote:
? Hi Tim,
My apologies, I should have mentioned, I’m hoping for one that fits the rip fence of the K700S.
Thx,
Wade
On Dec 15, 2024, at 5:28?PM, Tim Prinzing via groups.io <tim.prinzing@...> wrote:
? I just went to the Proscale website and noticed this for Felder K700 with 1800mm crosscut fence:
? --Tim On Sun, Dec 15, 2024 at 5:36?PM Wade Dees via <wjdsignature= [email protected]> wrote: Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
Brian,
I’m looking for a DRO to install on the rip fence of the K700S. ?Something that sits on the main casting hub of the rip assembly. ?
I have the heavy duty Felder flip stops with DRO already. ?Love that setup! ?
Thx,
Wade
toggle quoted message
Show quoted text
On Dec 16, 2024, at 7:29?AM, Brian Lamb via groups.io <blamb11@...> wrote:
? You guys do realize that Proscale or Imran's contraption do nothing to get rid of the crappy flipstop that Felder uses and isn't square. I am also not sure I would want to trust the flimsy 3D printed brackets that I'm seeing here to hold the electronics. One good bump with a board will have the units in multiple pieces... of course if the STL is provided you can always print another, consider it a consumable.
Brian Lamb blamb11@... lambtoolworks.com
On Sunday, December 15, 2024 at 06:27:50 PM MST, Tim Prinzing via groups.io <tim.prinzing@...> wrote:
I just went to the Proscale website and noticed this for Felder K700 with 1800mm crosscut fence:
? --Tim On Sun, Dec 15, 2024 at 5:36?PM Wade Dees via <wjdsignature= [email protected]> wrote: Accurate technology Inc. makes great DRO’s!
I’m hoping one day they will develope a kit for the K700S. ?
Wade
On Dec 15, 2024, at 2:30?PM, Aaron Inami <ainami@...> wrote:
? Andrea,
?
By the way, Proscale does already have a kit for the Minimax SC4:
?
-Aaron
|
imran
Bill Belanger
Bryce Comer