开云体育

Spiral cutter stuck torx head screw. AD941

#ad941 #helps #jointer #jointerplaner

Chris All Messages By This Member #132852 Hi there, I have 2x stuck torx head screws (I think that's the name) stuck?my spiral cutter . The heads are not stripped. To scared to push it too hard. Does anyone have any recommendations on how to loosen them? Thanks Chris.
James Zhu All Messages By This Member #132853 It is T20 torx head screw.? When I tried to loose the screw the very first time, I felt I would break my wrist.? If you have a long wrench with the T20 bit, it would be a lot easier. James toggle quoted message Show quoted text On Mon, Oct 30, 2023 at 7:20 PM Chris <Hope752@...> wrote: Hi there, I have 2x stuck torx head screws (I think that's the name) stuck?my spiral cutter . The heads are not stripped. To scared to push it too hard. Does anyone have any recommendations on how to loosen them? Thanks Chris.
Brian Lamb All Messages By This Member #132854 开云体育 Did you consider an impact driver? The impact nature of it will generally break loose the screw. Brian Lamb blamb11@... www.lambtoolworks.com toggle quoted message Show quoted text On Oct 30, 2023, at 4:19 PM, Chris <Hope752@...> wrote: Hi there, I have 2x stuck torx head screws (I think that's the name) stuck?my spiral cutter . The heads are not stripped. To scared to push it too hard. Does anyone have any recommendations on how to loosen them? Thanks Chris.
David Davies All Messages By This Member #132855 soak?with PB Blaster and maybe heat Dave Davies toggle quoted message Show quoted text On Mon, Oct 30, 2023 at 6:43?PM Brian Lamb <blamb11@...> wrote: Did you consider an impact driver? The impact nature of it will generally break loose the screw. Brian Lamb blamb11@... On Oct 30, 2023, at 4:19 PM, Chris <Hope752@...> wrote: Hi there, I have 2x stuck torx head screws (I think that's the name) stuck?my spiral cutter . The heads are not stripped. To scared to push it too hard. Does anyone have any recommendations on how to loosen them? Thanks Chris. -- Dave & Marie Davies 318-219-7868
mac campshure All Messages By This Member #132857 开云体育 I used to remove stuck screws from cutterheads for ?Ortlie tools . Used a fine point on propane torch with good fitting tool.? Make sure cutterhead doesn’t move. Mac,, martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330?cell airtightclamps@... Designing and building for 50 years toggle quoted message Show quoted text On Oct 30, 2023, at 6:45 PM, David Davies <myfinishingtouch@...> wrote: ? soak?with PB Blaster and maybe heat Dave Davies On Mon, Oct 30, 2023 at 6:43?PM Brian Lamb <blamb11@...> wrote: Did you consider an impact driver? The impact nature of it will generally break loose the screw. Brian Lamb blamb11@... On Oct 30, 2023, at 4:19 PM, Chris <Hope752@...> wrote: Hi there, I have 2x stuck torx head screws (I think that's the name) stuck?my spiral cutter . The heads are not stripped. To scared to push it too hard. Does anyone have any recommendations on how to loosen them? Thanks Chris. -- Dave & Marie Davies 318-219-7868
Jim Dayton All Messages By This Member #132860 I'd use an impact screwdriver...something like?Lisle 29200. These are tremendously useful in cases like this where you need some extra force to make sure the fastener doesn't strip while trying to turn out. Everyone should own one! Jim toggle quoted message Show quoted text On Mon, Oct 30, 2023 at 9:59?PM mac campshure via <mac512002=[email protected]> wrote: I used to remove stuck screws from cutterheads for ?Ortlie tools . Used a fine point on propane torch with good fitting tool.? Make sure cutterhead doesn’t move. Mac,, martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330?cell airtightclamps@... Designing and building for 50 years On Oct 30, 2023, at 6:45 PM, David Davies <myfinishingtouch@...> wrote: ? soak?with PB Blaster and maybe heat Dave Davies On Mon, Oct 30, 2023 at 6:43?PM Brian Lamb <blamb11@...> wrote: Did you consider an impact driver? The impact nature of it will generally break loose the screw. Brian Lamb blamb11@... On Oct 30, 2023, at 4:19 PM, Chris <Hope752@...> wrote: Hi there, I have 2x stuck torx head screws (I think that's the name) stuck?my spiral cutter . The heads are not stripped. To scared to push it too hard. Does anyone have any recommendations on how to loosen them? Thanks Chris. -- Dave & Marie Davies 318-219-7868
Chris All Messages By This Member #132861 Thanks everyone for the ideas. Tapping with the hammer with 1/4" drive did the trick.
mac campshure All Messages By This Member #132863 开云体育 Yes I pull mine out every know and than, handy tool. Heat and a little squirt of liquid wrench.? martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330?cell airtightclamps@... Designing and building for 50 years toggle quoted message Show quoted text On Oct 31, 2023, at 3:38 AM, Chris <Hope752@...> wrote: ?Thanks everyone for the ideas. Tapping with the hammer with 1/4" drive did the trick.
mac campshure All Messages By This Member #132864 开云体育 ? martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330?cell airtightclamps@... Designing and building for 50 years toggle quoted message Show quoted text On Oct 31, 2023, at 8:21 AM, mac campshure <mac512002@...> wrote: ?Yes I pull mine out every know and than, handy tool. Heat and a little squirt of liquid wrench.? martin/campshure/co/llc mac campshure 7412 elmwood ave. middleton, wi 53562-3106 608-332-2330?cell airtightclamps@... Designing and building for 50 years On Oct 31, 2023, at 3:38 AM, Chris <Hope752@...> wrote: ?Thanks everyone for the ideas. Tapping with the hammer with 1/4" drive did the trick.

Previous Topic Next Topic