¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Felderownersgroup
  2. Messages
Expanded Topics Messages Polls
Date
Re: Groover / Dado advice

 

After removing the saw blade, remove the flange (part number 9 on page 54 of my 2017 manual). The dado set will then sit against the arbor.

Also, do not attempt to use the spacer that is part of the Hammer dado set. When I called the tech, many years ago, he said they had never been asked about this.

Steve, Nashville, TN
Re: Groover / Dado advice

 

A bit off topic, I have an older C3-31 and do not see a way to install a dado set of any kind as the arbor seems too short. I'm considering getting a 1/4" kerf blade and going the multiple cut route but wanted to make sure I'm understanding the possibilities.
?
Thanks
Re: Kundig Uniq

 

The owner's at?5132036539 if you want to text him about the Kundig
Dave Davies

On Sat, Dec 28, 2024 at 5:27?PM Steve Rowe via <steverowe734=[email protected]> wrote:
I have had the Kundig Uniq since 2010 and at $7500 it is a bargain.? New prices in 2010 were around $15K.? I had a power feeder functioning as an auxiliary dust collector after upgrading to a CoMatic DC40 so recently added a power feeder bracket as shown in the photo.? There are termination points and spare cable glands already existing in the electrical cabinet so powering the feeder was easy.? Kundig had previously discontinued the bracket but will make it to order and it was less than I could have had one made.? If you call Kundig, they may not know about it but this is the information: ?Kundig Part: 20-09550-08 - Support for feed unit - Console
Steve



--
Dave & Marie Davies

318-219-7868
Re: New video.

 

¿ªÔÆÌåÓý

Yes Wade.

Imran Malik
IAM Wood Creations

On Dec 29, 2024, at 11:41?AM, Wade Dees <wjdsignature@...> wrote:

?
Imran,

This lock miter cutter was this done on the shaper?

Thx,

Wade

On Dec 29, 2024, at 8:31?AM, imranindiana via groups.io <imranindiana@...> wrote:

?

Very nice work Bryce and thanks for sharing. I know the tape technique but I can¡¯t bring myself to doing it because I can¡¯t see if the joint is completely closed. So I resorted to lock miter on this 19 ft long beam wrap. It was a lot of fun with staggered scarf joints on all 3 sides and had to be glued on-site due to the length.

?

Imran Malik

IAM Wood Creations

?

From: [email protected] On Behalf Of Bryce Comer via groups.io
Sent: Saturday, December 28, 2024 5:15 PM
To: [email protected]
Subject: [FOG] New video.

?

Hi all,

Happy holidays!

Just thought i would post a link here to my latest video. Not a huge amount of work on the Felder CF 741, but hopefully enough to keep you interested. :)

Hope you enjoy it.

Regards,

Bryce

--


<IMG_7045.JPG>
<IMG_7045.JPG>
<IMG_7072.JPG>
Re: New video.

 

¿ªÔÆÌåÓý

Imran,

This lock miter cutter was this done on the shaper?

Thx,

Wade

On Dec 29, 2024, at 8:31?AM, imranindiana via groups.io <imranindiana@...> wrote:

?

Very nice work Bryce and thanks for sharing. I know the tape technique but I can¡¯t bring myself to doing it because I can¡¯t see if the joint is completely closed. So I resorted to lock miter on this 19 ft long beam wrap. It was a lot of fun with staggered scarf joints on all 3 sides and had to be glued on-site due to the length.

?

Imran Malik

IAM Wood Creations

?

From: [email protected] On Behalf Of Bryce Comer via groups.io
Sent: Saturday, December 28, 2024 5:15 PM
To: [email protected]
Subject: [FOG] New video.

?

Hi all,

Happy holidays!

Just thought i would post a link here to my latest video. Not a huge amount of work on the Felder CF 741, but hopefully enough to keep you interested. :)

Hope you enjoy it.

Regards,

Bryce

--


<IMG_7045.JPG>
<IMG_7045.JPG>
<IMG_7072.JPG>
Re: New video.

 

¿ªÔÆÌåÓý

Very nice work Bryce and thanks for sharing. I know the tape technique but I can¡¯t bring myself to doing it because I can¡¯t see if the joint is completely closed. So I resorted to lock miter on this 19 ft long beam wrap. It was a lot of fun with staggered scarf joints on all 3 sides and had to be glued on-site due to the length.

?

Imran Malik

IAM Wood Creations

?

From: [email protected] On Behalf Of Bryce Comer via groups.io
Sent: Saturday, December 28, 2024 5:15 PM
To: [email protected]
Subject: [FOG] New video.

?

Hi all,

Happy holidays!

Just thought i would post a link here to my latest video. Not a huge amount of work on the Felder CF 741, but hopefully enough to keep you interested. :)

Hope you enjoy it.

Regards,

Bryce

--


IMG_7045.JPG
IMG_7045.JPG
IMG_7072.JPG

Re: New video.

 

Douglas Fir aka "Oregon Pine" in Sweden.? What do they call it down there?? Seems radiata pine from NZ would be more available but maybe not match existing trim.
Re: New video.

 

I will never get enough of real shop work videos. Smart work and lovely results. Thanks for sharing.?


On Sat, Dec 28, 2024 at 6:48?PM Bon May via <bonmay1=[email protected]> wrote:
Really nice piece Bryce, thanks for showing that one. I love VG Fir trim...
?
Bon



--
Brett Wissel
Saint Louis Restoration
1831 S Kingshighway Blvd (at Shaw Blvd)
St Louis, MO 63110

314.772.2167
brett@...
Re: Looking at FELDER Dual 51

 

Jim,
?
I had an AD-941 and really liked it.? I was able to sell it for what I paid for it and wanted a 20" machine.
?
I decided to get the SCM L'invincible FS 7 in January of 2022 and it was delivered in February of 2023.? It is a joy to use.
?
PM me with any questions.
?
PK
Re: Looking at FELDER Dual 51

 

Thank you Tom!
Re: Looking at FELDER Dual 51

 

Thank you Mike. Your information is very much appreciated!
Re: Groover / Dado advice

 

¿ªÔÆÌåÓý

Kamal,

8¡± dado or saw blade will fit in the shaper hood. I don¡¯t know if running a saw blade is worse than an equivalent shaper cutter but it seems that way to me. Lot more cutting teeth than 2 or 4 on a cutterhead but both will ruin one¡¯s day for sure, to say the least.

Safest would be a false fence. In my case, I used the Felder safety bars so I have a continuous ¡°fence¡± for the material. I did make nearly 3¡± deep slots as shown in this picture. I tried the narrower slot (lower one in the picture) on K975 saw with an 350mm Tenryu tipping blade annd an home made jig. I did not get consistent results and it was much harder. Running this cut on the shaper was no different than any other shaper operation.

image1.jpeg

Imran Malik
IAM Wood Creations

On Dec 28, 2024, at 11:07?AM, KRPatel via groups.io <kamalsonal@...> wrote:

?
Thanks Imran and Jacques...did not know that those dados will work on a shaper...do I treat it as a "normal" shaper when placing it in the shaper or other precautions / pointers?
?
Kamal Patel
Re: Looking at FELDER Dual 51

Mike D.
 

Jim:
I have the AD951, probably 5 years now. During this time, I¡¯ve pushed it hard, with rough sawn hardwoods; often running Jatoba and purple heart. The machine serves me well. My sense is that it is a better planer than jointer, though this is just an impression I have.

The power drive is precise. I¡¯ve added extensions to the planer bed. Dust collection is good, though I dislike having to changeover the dust hood position when changing over the function. Also, the fence is Cumbersome, with it¡¯s side attachment point, and setting a miter is functional, but inelegant and?without a fine adjustment. As with other Felder equipment I own, I feel that most?elements are professional grade and well thought out, while others seem oddly?lacking.

If I was in the market again, I would look at what?Martin has to offer (if only to rule it out for this or that reason) ?-?my understanding is that Griggio?makes a machine?for them),?then the SCM machines. I have no knowledge of either of these. The thought of going separates is ever-present, but never wins against space and cost.

Mike D.




On Saturday, December 28, 2024, 14:46, Jim Synyard via groups.io <Jimsynyard@...> wrote:

I am looking at buying the Dual 51 JP combo new from FELDER. My question is this, has anyone bought one of these recently and if so do you have any objections or recommendations? Any unbiased information would be greatly appreciated. Thank you.?

--
Mike D.
Annapolis, MD
AD951; K700S; N4400
Re: Looking at FELDER Dual 51

 

Hi Jim,?
?
David Best has researched this topic extensively and would be able to provide an insightful response on the pros- and cons- of the Felder combination machines.?
?
There are a handful of users here who have the SCM FS-7 and seem to really like it.?
?
I am using the SCM FS-52es and I really like it. It has the same capacity as the FS-7, but with less complexity. My machine has the Tersa head and I prefer it to the spiral heads. ?
?
Best wishes on your machine journey,
--
Tom Gensmer
Heritage Home Renewals, LLC
Minneapolis, MN
Re: New video.

 

Really nice piece Bryce, thanks for showing that one. I love VG Fir trim...
?
Bon
Re: New video.

 

Nice work! You don't see a lot of that type of work anymore, well done.

Brian Lamb
blamb11@...
lambtoolworks.com


On Saturday, December 28, 2024 at 04:20:50 PM MST, Bryce Comer <bryce@...> wrote:


Hi all,
Happy holidays!
Just thought i would post a link here to my latest video. Not a huge amount of work on the Felder CF 741, but hopefully enough to keep you interested. :)
Hope you enjoy it.
Regards,
Bryce
--
https://www.brycecomerwoodworks.com/
https://www.youtube.com/channel/UCHdrRaAZd_pOa7wwbdNPUEw
Re: Kundig Uniq

 

I have had the Kundig Uniq since 2010 and at $7500 it is a bargain.? New prices in 2010 were around $15K.? I had a power feeder functioning as an auxiliary dust collector after upgrading to a CoMatic DC40 so recently added a power feeder bracket as shown in the photo.? There are termination points and spare cable glands already existing in the electrical cabinet so powering the feeder was easy.? Kundig had previously discontinued the bracket but will make it to order and it was less than I could have had one made.? If you call Kundig, they may not know about it but this is the information: ?Kundig Part: 20-09550-08 - Support for feed unit - Console
Steve
New video.

 

Hi all,
Happy holidays!
Just thought i would post a link here to my latest video. Not a huge amount of work on the Felder CF 741, but hopefully enough to keep you interested. :)
Hope you enjoy it.
Regards,
Bryce
--
https://www.brycecomerwoodworks.com/
https://www.youtube.com/channel/UCHdrRaAZd_pOa7wwbdNPUEw
Looking at FELDER Dual 51

 

I am looking at buying the Dual 51 JP combo new from FELDER. My question is this, has anyone bought one of these recently and if so do you have any objections or recommendations? Any unbiased information would be greatly appreciated. Thank you.?
Re: Groover / Dado advice

 

Thanks Imran and Jacques...did not know that those dados will work on a shaper...do I treat it as a "normal" shaper when placing it in the shaper or other precautions / pointers?
?
Kamal Patel
2361 - 2380 of 141151