|
Re: can anyone identify this thin plastic part?
That's it. Thanks Wade. On Tue, May 13, 2025, 9:19 PM Wade Dees via <wjdsignature=[email protected]> wrote:
|
|
Re: can anyone identify this thin plastic part?
¿ªÔÆÌåÓýJohn, Here¡¯s a picture of that plastic piece. ?Hopefully you can make it out. ?I have my telescoping extension removed from the 1100mm cross cut fence. ?This plastic disc sits right where the threads come through the main fence body from the knob thats used to tighten the telescopic fence in place.? Wade ? On May 13, 2025, at 4:30?PM, John Ormsby via groups.io <jobcat123@...> wrote:
|
|
Re: can anyone identify this thin plastic part?
toggle quoted message
Show quoted text
On May 13, 2025, at 3:56 PM, John Ormsby via groups.io <jobcat123@...> wrote:
|
|
can anyone identify this thin plastic part?
Hello, I am in the middle of selling things and have been taking some items apart to make it easier to pack for shipping. I found this on the ground and am trying to identify what thing it goes to so I can put it in the proper box.
?
It is about 24.8mm x 35.5mm at the outer curves and about 1mm thinck with a small solid round cylinder in the middle. The cylinder must fit into a hole in order to keep it in place.
?
Your help is much appreciated. John |
|
Re: Hammer C3 31 rotary converter
Check you safety switches. They might be causing the motor not receiving power. Check emo stops as well as latches on shaper belt hatch/saw slide. It should be halfway between up and down. Kind regards,? Jonathan? On 13 May 2025 16:24, "Brian Lamb via groups.io" <blamb11@...> wrote:
|
|
2023 Felder K 700
I am selling my 2023 Felder K 700 sliding table saw that is in exceptional condition. ?I ordered it new from Felder DE and have sparingly used it in my home shop in Wyomissing PA (Eastern PA). ?I thoroughly like the function and quality of this saw, but I am trying to make more space in my small shop, and seem to be using my Felder machines (AD741 & FB510) more to process lumber to get to the bench. ?I am selling it for $7900. ?Please reach out to me if you have any additional questions. ?Thanks, Mark
?
This K700 saw is specked with:
- ?Single Phase 230v 60Hz 4 HP motor
- ?800mm Rip Fence
- ?1550mm Sliding Table
- ?1100mm Crosscut Fence with 1100mm Telescopic Pull-Out
- ?Dado Prep
- ?Two Dial Indicators
- ?Extractor Hose mount
- ?Micro Adjust for rip fence
- ?Eccentric Clamp and Auxiliary EM stop
- ?Three 315mm Blades. ?Rp, Combo and Fine cut
- ?Sliding width Extension?
- ?Mobility kit with Sunnex leveling feet
? |
|
Re: Hammer A3-31 Guard Hardware Question
Apparently I have a later model of the guard on mine (see picture).? However, it is a very simple construction: the spring needs to develop enough pressure to push the guard up and you adjust the guard height by screwing down the adjustment knob from above.?
?
?
If your guard does not lift up, you need to increase spring tension.? The nuts in your picture are roughly in the right order as far as I understand it. Counting from the bottom, you have the first two that hold the bolt in place on the bracket.? Nut #4 would need to be adjusted upwards to increase the spring tension and #3 works then as a counter nut to hold #4 in place once adjusted.?
?
Hope that helps,
Johannes |
|
Re: North State/Powermatic 16" Wide Belt Sander Mobility Kit
Like David Best, I made a plywood platform with supports underneath which allows me to move my 16" North State with a small pallet jack.?
?
I did try a mobile base, but the problem is that there isn't a good place/way to grab/steer the sander. The pallet jack makes for a good solution for this machine.?
--
Tom Gensmer Heritage Home Renewals, LLC Minneapolis, MN |
Jonathan Martens
Tom Gensmer
Bill Belanger