开云体育

How much shaper are you looking for? Joe in New Orleans had a great Format shaper for sale Sent: Thursday, November 26, 2020 6:04 PM To: [email protected] Subject: Re: [FOG] Would you buy a

Cliff, after posting i realized that i should have added some details. figured, i will wait to see if there is any interest to start with. but since you brought it up, here it goes: made out of CR1018

Or should I look to a Martin T60A and a separate Shaper? Seems like a bare bones T60A is not crazy more.? Then just wait for a great shaper used deal? Thoughts? PK

tell whether they can select their preference for the thread in the tapped hole.? mm? imperial,? & what size, that sort of thing

sooner or later you might need that power source upgrade anyhow.... thats what I did when I got my SCM 43" sander. I spent more on the infrastructure than the machine itself. but its good in long

Hi Brian and everyone else,Thanks so much for all the info. It seems like it wouldn’t be worth my time to retrofit. Marlowe I saw your ad on wood web but?I can’t run 10 HP with my phase

Super cool stool Michael.....also love the fencing in the background, is it Hazel? Kindest regards Jonathan Samways fineinteriorwoodwork.com richardmartinwindows.com

Very cool. I make rocking chairs and can use this idea! Where did you source the materials? Mark

Imran, Saved and on my desktop! That seems a fantastic resource and reference. Thank you very much. Best regards, Trevor Lusty Ireland

I consider Understanding Wood by Bruce Hoadley as my wood Quran but i learned about this free 590 page wood handbook from JLC article put out by USDA. I have only taken a quick look but i do not think

Hi John, I can’t answer your question, however, I have a Powermatic 1632 open ended wide belt sander in my garage that I have been meaning to sell. It is a 7.5 hp, 3 phase unit. I bought it when it

well i need to make a few for myself and thought i check if anyone is interested. this is basic cold rolled steel 1018. pre xroll slider need two edges chamfered. i am thinking 1 for $25, 2 for $40

Dave summed it up well. Can be done, but might be easier and cheaper to go with a transformer. I have a 24" Powermatic widebelt on woodweb if you have interest in a plug and play machine. Marlowe

I've swapped 575v for 230 and there can be lots to replace. You need to be sure of the IEC frame size and then see if 7.5 230v motor can be had in that size and shaft length for a reasonable cost. If

You would need to make sure any control logic transformers are swapped, not hard. Typically there is a transformer to power the controls. That would need to be changed too, not hard or expensive. I

james, first, there is no telling what each of us get when ordering from china. assuming specified power means something, the 5mW red focusable laser i purchased for about what you paid is not very

Hi guys,I’m looking at a used Holytek 15” open ended?wide belt sander that is 10hp and??575 volts. By the time I get a transformer and possibly a larger phase converter I will have spent more

I bought this 660nm 5mW Industrial Focusable Laser Line Module/Locator Laser with PSU&Bracket (only $15) last year, and have not installed it. https://www.ebay.ca/itm/261278696170 James

I made this purchase myself as well..I'm looking at various ways to mount it to a platform off my ceiling so it hangs about 9 feet off finish floor, but about 5 feet off the sliding table so hopefully

@Mark, you can see that blade in action in this thread: /g/felderownersgroup/topic/stool_progress/77800964?p=,,,100,0,0,0::recentpostdate%2Fsticky,,,100,2,0,77800964 The stool I was