hello Roman, "n" is a common symbol for r.p.m. (revolutions per minute). regards, Stuart, NZ
On 19/05/2025 06:49 NZST roman fox via groups.io <romanfox68@...> wrote:
?
?
Hi Vedran thank you for this idea i was looked in to manual for v 10 and it is say only speed off pulley 4500 ,8000 ,12000RPM and low speed should be use for outernal grinding id higher for internal grinding ,nothing about motor RPM .But few weeks a go i have luck and i bought TP grinder but some wire which go into motorr are burn so i have to fix this problem , and on motor is not actually rpm? but is " n - 7000 it is torque ? in newtometer??
Before wires was burn grinder has whistle noise and after proper clean bearing i find out the back one dos not run smoothly so a replaced both two bearings and afcourse automaticly replace motors and it was much quit .I will see after i fix problem with wires .? ?,my regards Roman
---------- P?vodn¨ª e-mail ----------
Od: Vedran via groups.io <vedran.groups@...>
Komu: [email protected] <[email protected]>
Datum: 18. 5. 2025 10:08:47
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
Motor is brushed universal AC type so it¡¯s pretty fast and loud but I¡¯m not sure about the exact speed and I don¡¯t have access to a v10 manual at the moment. TP grinder deatails are in there, you can look them up. The spindle has three pullies that cover the range from 4500 to 12000 RPM.
?
Regards
?
Vedran
?
On Sunday, May 18, 2025, roman fox via <romanfox68=[email protected]> wrote:
Hi Vedran ,OK i will put you on list ,by the way thank you for find this marking system , i will call tomorrow for some questions into TYROLIT but in this moment i know the wheels can be finish in white or brown collor - brown are more expensive when i asked if is some significant different in properties technician tell me is not only has to be add pigment for collor .
Question about the TP grinder motor, this motor has 7000 rpm ??
?my regards Roman
---------- P?vodn¨ª e-mail ----------
Od: Vedran via <vedran.groups=gmail.com@groups.io>
Komu: [email protected] Datum: 18. 5. 2025 0:18:55
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
If I'm reading this correctly, it's medium hardness, brown Al oxide, open structured wheel, good up to 11000 RPM. Emco TP grinder goes up to 12000 RPM, but going by the manual, we're only supposed to use slow gear (4500 RPM) for OD grinding so it should be fine.
?
I don't really need them either, but sign me up for 3 pieces Roman
?
?
Regards
?
Vedran
On Sat, May 17, 2025 at 11:37?AM roman fox via <romanfox68=seznam.cz@groups.io> wrote:
Hi James this is like i hope specification on material a grit for grinding wheel?
more specification i will know at monday when everybody will in job .by the way like they pointed ,when i put order for manufacture it take maximum 8 weeks? but i will questioned too if it can be shorter time.
?my regards Roman
---------- P?vodn¨ª e-mail ----------
Od: James via <jchaiefx=[email protected]>
Komu: [email protected] Datum: 17. 5. 2025 0:38:21
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Roman
Some more information would be useful, what kind of stones are they, Alummium Oxide ?
Considering that grinding wheels that fit the 16mm arbor of the Emco toolpost grinder
are discontinued, are these new manufactured or new old stock ?
I guess they're flat wheels ? Any cup wheels ?
?
James
?
?
?
?
?
?
--
Regards
?
Vedran
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
On 19/05/2025 06:49 NZST roman fox via groups.io <romanfox68@...> wrote:
?
?
Hi Vedran thank you for this idea i was looked in to manual for v 10 and it is say only speed off pulley 4500 ,8000 ,12000RPM and low speed should be use for outernal grinding id higher for internal grinding ,nothing about motor RPM .But few weeks a go i have luck and i bought TP grinder but some wire which go into motorr are burn so i have to fix this problem , and on motor is not actually rpm? but is " n - 7000 it is torque ? in newtometer??
Before wires was burn grinder has whistle noise and after proper clean bearing i find out the back one dos not run smoothly so a replaced both two bearings and afcourse automaticly replace motors and it was much quit .I will see after i fix problem with wires .? ?,my regards Roman
---------- P?vodn¨ª e-mail ----------
Od: Vedran via groups.io <vedran.groups@...>
Komu: [email protected] <[email protected]>
Datum: 18. 5. 2025 10:08:47
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
Motor is brushed universal AC type so it¡¯s pretty fast and loud but I¡¯m not sure about the exact speed and I don¡¯t have access to a v10 manual at the moment. TP grinder deatails are in there, you can look them up. The spindle has three pullies that cover the range from 4500 to 12000 RPM.
?
Regards
?
Vedran
?
On Sunday, May 18, 2025, roman fox via <romanfox68=[email protected]> wrote:
Hi Vedran ,OK i will put you on list ,by the way thank you for find this marking system , i will call tomorrow for some questions into TYROLIT but in this moment i know the wheels can be finish in white or brown collor - brown are more expensive when i asked if is some significant different in properties technician tell me is not only has to be add pigment for collor .
Question about the TP grinder motor, this motor has 7000 rpm ??
?my regards Roman
---------- P?vodn¨ª e-mail ----------
Od: Vedran via <vedran.groups=gmail.com@groups.io>
Komu: [email protected] Datum: 18. 5. 2025 0:18:55
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
If I'm reading this correctly, it's medium hardness, brown Al oxide, open structured wheel, good up to 11000 RPM. Emco TP grinder goes up to 12000 RPM, but going by the manual, we're only supposed to use slow gear (4500 RPM) for OD grinding so it should be fine.
?
I don't really need them either, but sign me up for 3 pieces Roman
?
?
Regards
?
Vedran
On Sat, May 17, 2025 at 11:37?AM roman fox via <romanfox68=seznam.cz@groups.io> wrote:
Hi James this is like i hope specification on material a grit for grinding wheel?
more specification i will know at monday when everybody will in job .by the way like they pointed ,when i put order for manufacture it take maximum 8 weeks? but i will questioned too if it can be shorter time.
?my regards Roman
---------- P?vodn¨ª e-mail ----------
Od: James via <jchaiefx=[email protected]>
Komu: [email protected] Datum: 17. 5. 2025 0:38:21
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Roman
Some more information would be useful, what kind of stones are they, Alummium Oxide ?
Considering that grinding wheels that fit the 16mm arbor of the Emco toolpost grinder
are discontinued, are these new manufactured or new old stock ?
I guess they're flat wheels ? Any cup wheels ?
?
James
?
?
?
?
?
?
--
Regards
?
Vedran
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Vedran thank you for this idea i was looked in to manual for v 10 and it is say only speed off pulley 4500 ,8000 ,12000RPM and low speed should be use for outernal grinding id higher for internal grinding ,nothing about motor RPM .But few weeks a go i have luck and i bought TP grinder but some wire which go into motorr are burn so i have to fix this problem , and on motor is not actually rpm? but is " n - 7000 it is torque ? in newtometer??
Before wires was burn grinder has whistle noise and after proper clean bearing i find out the back one dos not run smoothly so a replaced both two bearings and afcourse automaticly replace motors and it was much quit .I will see after i fix problem with wires .? ?,my regards Roman
Motor is brushed universal AC type so it¡¯s pretty fast and loud but I¡¯m not sure about the exact speed and I don¡¯t have access to a v10 manual at the moment. TP grinder deatails are in there, you can look them up. The spindle has three pullies that cover the range from 4500 to 12000 RPM.
Regards
Vedran
On Sunday, May 18, 2025, roman fox via <romanfox68=[email protected]> wrote:
Hi Vedran ,OK i will put you on list ,by the way thank you for find this marking system , i will call tomorrow for some questions into TYROLIT but in this moment i know the wheels can be finish in white or brown collor - brown are more expensive when i asked if is some significant different in properties technician tell me is not only has to be add pigment for collor .
Question about the TP grinder motor, this motor has 7000 rpm ??
?my regards Roman
If I'm reading this correctly, it's medium hardness, brown Al oxide, open structured wheel, good up to 11000 RPM. Emco TP grinder goes up to 12000 RPM, but going by the manual, we're only supposed to use slow gear (4500 RPM) for OD grinding so it should be fine.
I don't really need them either, but sign me up for 3 pieces Roman
Regards
Vedran
On Sat, May 17, 2025 at 11:37?AM roman fox via <romanfox68=seznam.cz@groups.io> wrote:
Hi James this is like i hope specification on material a grit for grinding wheel?
more specification i will know at monday when everybody will in job .by the way like they pointed ,when i put order for manufacture it take maximum 8 weeks? but i will questioned too if it can be shorter time.
?my regards Roman
---------- P?vodn¨ª e-mail ---------- Od: James via <jchaiefx=[email protected]> Komu: [email protected] Datum: 17. 5. 2025 0:38:21 P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Roman
Some more information would be useful, what kind of stones are they, Alummium Oxide ?
Considering that grinding wheels that fit the 16mm arbor of the Emco toolpost grinder
are discontinued, are these new manufactured or new old stock ?
I guess they're flat wheels ? Any cup wheels ?
?
James
?
?
--
Regards
Vedran
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
Motor is brushed universal AC type so it¡¯s pretty fast and loud but I¡¯m not sure about the exact speed and I don¡¯t have access to a v10 manual at the moment. TP grinder deatails are in there, you can look them up. The spindle has three pullies that cover the range from 4500 to 12000 RPM.
On Sunday, May 18, 2025, roman fox via <romanfox68=[email protected]> wrote:
Hi Vedran ,OK i will put you on list ,by the way thank you for find this marking system , i will call tomorrow for some questions into TYROLIT but in this moment i know the wheels can be finish in white or brown collor - brown are more expensive when i asked if is some significant different in properties technician tell me is not only has to be add pigment for collor .
Question about the TP grinder motor, this motor has 7000 rpm ??
?my regards Roman
If I'm reading this correctly, it's medium hardness, brown Al oxide, open structured wheel, good up to 11000 RPM. Emco TP grinder goes up to 12000 RPM, but going by the manual, we're only supposed to use slow gear (4500 RPM) for OD grinding so it should be fine.
I don't really need them either, but sign me up for 3 pieces Roman
Regards
Vedran
On Sat, May 17, 2025 at 11:37?AM roman fox via <romanfox68=seznam.cz@groups.io> wrote:
Hi James this is like i hope specification on material a grit for grinding wheel?
more specification i will know at monday when everybody will in job .by the way like they pointed ,when i put order for manufacture it take maximum 8 weeks? but i will questioned too if it can be shorter time.
?my regards Roman
---------- P?vodn¨ª e-mail ---------- Od: James via <jchaiefx=[email protected]> Komu: [email protected] Datum: 17. 5. 2025 0:38:21 P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Roman
Some more information would be useful, what kind of stones are they, Alummium Oxide ?
Considering that grinding wheels that fit the 16mm arbor of the Emco toolpost grinder
are discontinued, are these new manufactured or new old stock ?
I guess they're flat wheels ? Any cup wheels ?
?
James
?
?
--
Regards
Vedran
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Vedran ,OK i will put you on list ,by the way thank you for find this marking system , i will call tomorrow for some questions into TYROLIT but in this moment i know the wheels can be finish in white or brown collor - brown are more expensive when i asked if is some significant different in properties technician tell me is not only has to be add pigment for collor .
Question about the TP grinder motor, this motor has 7000 rpm ??
If I'm reading this correctly, it's medium hardness, brown Al oxide, open structured wheel, good up to 11000 RPM. Emco TP grinder goes up to 12000 RPM, but going by the manual, we're only supposed to use slow gear (4500 RPM) for OD grinding so it should be fine.
I don't really need them either, but sign me up for 3 pieces Roman
Regards
Vedran
On Sat, May 17, 2025 at 11:37?AM roman fox via <romanfox68=[email protected]> wrote:
Hi James this is like i hope specification on material a grit for grinding wheel?
more specification i will know at monday when everybody will in job .by the way like they pointed ,when i put order for manufacture it take maximum 8 weeks? but i will questioned too if it can be shorter time.
?my regards Roman
---------- P?vodn¨ª e-mail ---------- Od: James via <jchaiefx=[email protected]> Komu: [email protected] Datum: 17. 5. 2025 0:38:21 P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Roman
Some more information would be useful, what kind of stones are they, Alummium Oxide ?
Considering that grinding wheels that fit the 16mm arbor of the Emco toolpost grinder
are discontinued, are these new manufactured or new old stock ?
I guess they're flat wheels ? Any cup wheels ?
?
James
?
?
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
If I'm reading this correctly, it's medium hardness, brown Al oxide, open structured wheel, good up to 11000 RPM. Emco TP grinder goes up to 12000 RPM, but going by the manual, we're only supposed to use slow gear (4500 RPM) for OD grinding so it should be fine.
I don't really need them either, but sign me up for 3 pieces Roman
more specification i will know at monday when everybody will in job .by the way like they pointed ,when i put order for manufacture it take maximum 8 weeks? but i will questioned too if it can be shorter time.
?my regards Roman
---------- P?vodn¨ª e-mail ---------- Od: James via <jchaiefx=[email protected]> Komu: [email protected] Datum: 17. 5. 2025 0:38:21 P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Roman
Some more information would be useful, what kind of stones are they, Alummium Oxide ?
Considering that grinding wheels that fit the 16mm arbor of the Emco toolpost grinder
are discontinued, are these new manufactured or new old stock ?
I guess they're flat wheels ? Any cup wheels ?
?
James
?
?
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
more specification i will know at monday when everybody will in job .by the way like they pointed ,when i put order for manufacture it take maximum 8 weeks? but i will questioned too if it can be shorter time.
Answer for cup wheels ,James i am not sure if you thinking cup wheels in this dimensions emco grinder use arbour but i can ask but again minimum order can be probably less like in this wheels but will probably more expensive i would say if i remember technician told me the minimum mount of grinding powder what they can mix it is 2,5 kg so depence how many they will able manufacture from it? , and yes wheels i offer are flat , my regards Roman
Hi James i can find more if you like just tell hwat you interesting for ,in this moment i know that mixture should be to 55 rockwell can be in brown or white collor this wheels are brand new company will make them for my order also dimensions but minimum order is 50 pieces ,company name is TYROLIT check up your self quality of they product , send me your specific question and i will contact technician in company and i will ask them for you no problem James ,
Hi Andrei i can have only one grid - 60 or 80 depence how many people choose one more .Always i have to ordrer minimum 50 grinding wheels in one type
of grit , M80 for general use recommendet this say manual for TPG
---------- P?vodn¨ª e-mail ----------
Od: Andrei via groups.io <calciu1@...>
Komu: [email protected] <[email protected]>
Datum: 16. 5. 2025 15:49:10
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Roman. A set is both grits M60 and M80.?
But, I just wanted to mention that I don't need any. I just bought a nice grinder that uses much bigger wheels
Andrei two wholle sets you mean two wheels?
---------- P?vodn¨ª e-mail ----------
Od: Andrei via groups.io <calciu1@...>
Komu: [email protected] <[email protected]>
Datum: 16. 5. 2025 15:03:18
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
At a price of 12 Euro (about 13 dollars), I would buy two whole sets. Who knows when such a buying opportunity will come again.
Roman, I just wore out my original wheel and have been unsuccessful trying to find a replacement here in the states. Please place me on your list for 3 Wheels. Either M80 or M60 is ok for me. Your email comes at an opportune time, Clyde Jones
On Friday, May 16, 2025 at 04:41:33 AM EDT, roman fox via groups.io <romanfox68@...> wrote:
Hello all ,guys I have the opportunity to buy original size ,grinding wheels from the renowned company TYROLIT 65x6x16 mm ( grid M80, M60 depends on what we want, but only one type of grid for all wheels ), unfortunately the minimum quantity is 50 pieces,
the price for one including taxes is 12 eu, I would like to ask if anyone is interested, and how many pieces you will require ?? Thank you all for quick answer ,my regards Roman
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
Hi Andrei i can have only one grid - 60 or 80 depence how many people choose one more .Always i have to ordrer minimum 50 grinding wheels in one type of grit , M80 for general use recommendet this say manual for TPG
Andrei two wholle sets you mean two wheels?
---------- P?vodn¨ª e-mail ----------
Od: Andrei via groups.io <calciu1@...>
Komu: [email protected] <[email protected]>
Datum: 16. 5. 2025 15:03:18
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
At a price of 12 Euro (about 13 dollars), I would buy two whole sets. Who knows when such a buying opportunity will come again.
Roman, I just wore out my original wheel and have been unsuccessful trying to find a replacement here in the states. Please place me on your list for 3 Wheels. Either M80 or M60 is ok for me. Your email comes at an opportune time, Clyde Jones
On Friday, May 16, 2025 at 04:41:33 AM EDT, roman fox via groups.io <romanfox68@...> wrote:
Hello all ,guys I have the opportunity to buy original size ,grinding wheels from the renowned company TYROLIT 65x6x16 mm ( grid M80, M60 depends on what we want, but only one type of grid for all wheels ), unfortunately the minimum quantity is 50 pieces,
the price for one including taxes is 12 eu, I would like to ask if anyone is interested, and how many pieces you will require ?? Thank you all for quick answer ,my regards Roman
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
Andrei two wholle sets you mean two wheels?
---------- P?vodn¨ª e-mail ----------
Od: Andrei via groups.io <calciu1@...>
Komu: [email protected] <[email protected]>
Datum: 16. 5. 2025 15:03:18
P?edm¨§t: Re: [emcoV10lathe] TOOL POST GRINDER - NEW original grinding wheels for sale
At a price of 12 Euro (about 13 dollars), I would buy two whole sets. Who knows when such a buying opportunity will come again.
Roman, I just wore out my original wheel and have been unsuccessful trying to find a replacement here in the states. Please place me on your list for 3 Wheels. Either M80 or M60 is ok for me. Your email comes at an opportune time, Clyde Jones
On Friday, May 16, 2025 at 04:41:33 AM EDT, roman fox via groups.io <romanfox68@...> wrote:
Hello all ,guys I have the opportunity to buy original size ,grinding wheels from the renowned company TYROLIT 65x6x16 mm ( grid M80, M60 depends on what we want, but only one type of grid for all wheels ), unfortunately the minimum quantity is 50 pieces,
the price for one including taxes is 12 eu, I would like to ask if anyone is interested, and how many pieces you will require ?? Thank you all for quick answer ,my regards Roman
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
Roman, I just wore out my original wheel and have been unsuccessful trying to find a replacement here in the states. Please place me on your list for 3 Wheels. Either M80 or M60 is ok for me. Your email comes at an opportune time, Clyde Jones
On Friday, May 16, 2025 at 04:41:33 AM EDT, roman fox via groups.io <romanfox68@...> wrote:
Hello all ,guys I have the opportunity to buy original size ,grinding wheels from the renowned company TYROLIT 65x6x16 mm ( grid M80, M60 depends on what we want, but only one type of grid for all wheels ), unfortunately the minimum quantity is 50 pieces, the price for one including taxes is 12 eu, I would like to ask if anyone is interested, and how many pieces you will require ?? Thank you all for quick answer ,my regards Roman
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
Roman, I just wore out my original wheel and have been unsuccessful trying to find a replacement here in the states. Please place me on your list for 3 Wheels. Either M80 or M60 is ok for me. Your email comes at an opportune
time, Clyde Jones
On Friday, May 16, 2025 at 04:41:33 AM EDT, roman fox via groups.io <romanfox68@...> wrote:
Hello all ,guys I have the opportunity to buy original size ,grinding wheels from the renowned company TYROLIT 65x6x16 mm ( grid M80, M60 depends on what we want, but only one type of grid for all wheels ), unfortunately the minimum quantity is 50 pieces,
the price for one including taxes is 12 eu, I would like to ask if anyone is interested, and how many pieces you will require ?? Thank you all for quick answer ,my regards Roman
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
Roman, I just wore out my original wheel and have been unsuccessful trying to find a replacement here in the states. Please place me on your list for 3 Wheels. Either M80 or M60 is ok for me. Your email comes at an opportune
time, Clyde Jones
On Friday, May 16, 2025 at 04:41:33 AM EDT, roman fox via groups.io <romanfox68@...> wrote:
Hello all ,guys I have the opportunity to buy original size ,grinding wheels from the renowned company TYROLIT 65x6x16 mm ( grid M80, M60 depends on what we want, but only one type of grid for all wheels ), unfortunately the minimum quantity is 50 pieces,
the price for one including taxes is 12 eu, I would like to ask if anyone is interested, and how many pieces you will require ?? Thank you all for quick answer ,my regards Roman
Re: Milling head Maximat V10 first inspection: grease and oil
Regarding: "Any SAE 10 motor oil would work just fine, right?", the answer is NO.
?
Typical "motor oil" (for cars) includes detergents to suspend dirt & particles to be removed by a filter as the oil is pumped around.? I'm not sure about the geometry of the mill, but for lathes, you want any debris to settle into the bottom of the gear box.? It sounds like the V10 just uses grease, so that may not be an issue.
?
I have also heard there can be additives in some motor oils that don't play well with the bronze or zinc components used in some machine tools gear boxes.??
?
The safest bet is to use hydraulic oil, which doesn't contain much in the way of additives, beyond rust preventatives.? If it's just for exterior sliding surfaces (ways, column, quill), "way" oil is specifically designed for that.? Vactra #2 oil is the classic that has been around for at least 60 or 70 years.? It can be hard to find in small quantities, but large shops use it by the gallon.? You could probably talk them out of a cup worth in trade for a box of donuts.? There are also some vendors that cater to hobbyists that re-package it and sell it in small quantities.
?
The one caution about way oil is that it tends to stick, and then slip.? That's fine for things that are moved by lead screws & such.? I have a mill with a round ram, and when you try to rotate it to get it adjusted so the spindle is vertical, it is almost impossible to get it to move in small amounts if you use way oil.? Hydraulic oil works much better for that..??
?
Doug White
Re: TOOL POST GRINDER - NEW original grinding wheels for sale
Roman, I just wore out my original wheel and have been unsuccessful trying to find a replacement here in the states. Please place me on your list for 3 Wheels. Either M80 or M60 is ok for me. Your email comes at an opportune time, Clyde Jones
On Friday, May 16, 2025 at 04:41:33 AM EDT, roman fox via groups.io <romanfox68@...> wrote:
Hello all ,guys I have the opportunity to buy original size ,grinding wheels from the renowned company TYROLIT 65x6x16 mm ( grid M80, M60 depends on what we want, but only one type of grid for all wheels ), unfortunately the minimum quantity is 50 pieces, the price for one including taxes is 12 eu, I would like to ask if anyone is interested, and how many pieces you will require ?? Thank you all for quick answer ,my regards Roman
Re: Milling head Maximat V10 first inspection: grease and oil
Hello all ,guys I have the opportunity to buy original size ,grinding wheels from the renowned company TYROLIT 65x6x16 mm ( grid M80, M60 depends on what we want, but only one type of grid for all wheels ), unfortunately the minimum quantity is 50 pieces, the price for one including taxes is 12 eu, I would like to ask if anyone is interested, and how many pieces you will require ?? Thank you all for quick answer ,my regards Roman
