开云体育

Amusement: I want my Direqorl on a Raspberry PI to be an Igate but I will be. mile

Don Rolph All Messages By This Member #10352 So I have configured the IGATE servers and logged?in. I would now like to beacon over the iGate port if it is connected over internet. Since I am moving PBEACON?does not seem like it would work. So how does one do this? -- 73, AB1PH Don Rolph
David Ranch All Messages By This Member #10353 Edited Hello Don, If your Direwolf setup has a GPS and you have configured a TBEACON (not a PBEACON) have you found it's NOT sending the position packets to your IGATE??? Can you show us what you configured for your TBEACON line from the direwolf.conf file as well as the terminal output when you start Direwolf? ? Please note: PBEACONS are intended for static locations.. moving locations use TBEACONs (see the Direwolf User Guide Section 9.11.4 for full details) --David KI6ZHD On 03/04/2025 01:05 PM, Don Rolph via groups.io wrote: toggle quoted message Show quoted text So I have configured the IGATE servers and logged?in. ? I would now like to beacon over the iGate port if it is connected over internet. ? Since I am moving PBEACON?does not seem like it would work. ? So how does one do this? ? -- ? 73, AB1PH Don Rolph ?
Don Rolph All Messages By This Member #10354 David Ranch: no I looked?in the manual and all the PBEACONS?had coordinates configured so I assumed that PBEACONS are static.? I sense I may be confused on this point. toggle quoted message Show quoted text On Tue, Mar 4, 2025 at 4:30?PM David Ranch via <direwolf-groupsio=[email protected]> wrote: Hello Don, If your Direwolf setup has a GPS and you have configured a PBEACON, have you found it's NOT sending the position packets to your IGATE??? Can you show us what you configured for your PBEACON line from the direwolf.conf file as well as the terminal output when you start Direwolf? --David KI6ZHD On 03/04/2025 01:05 PM, Don Rolph via wrote: So I have configured the IGATE servers and logged?in. I would now like to beacon over the iGate port if it is connected over internet. Since I am moving PBEACON?does not seem like it would work. So how does one do this? -- 73, AB1PH Don Rolph -- 73, AB1PH Don Rolph
Don Rolph All Messages By This Member #10355 David: from the manual: PBEACON -?for a “position report.” This is generally used for your own location.?It has a fixed position. Later we will discuss TBEACON which gets the location from a GPS receiver. toggle quoted message Show quoted text On Tue, Mar 4, 2025 at 4:30?PM David Ranch via <direwolf-groupsio=[email protected]> wrote: Hello Don, If your Direwolf setup has a GPS and you have configured a PBEACON, have you found it's NOT sending the position packets to your IGATE??? Can you show us what you configured for your PBEACON line from the direwolf.conf file as well as the terminal output when you start Direwolf? --David KI6ZHD On 03/04/2025 01:05 PM, Don Rolph via wrote: So I have configured the IGATE servers and logged?in. I would now like to beacon over the iGate port if it is connected over internet. Since I am moving PBEACON?does not seem like it would work. So how does one do this? -- 73, AB1PH Don Rolph -- 73, AB1PH Don Rolph
David Ranch All Messages By This Member #10356 开云体育 Hello Don, I edited my response as I didn't fully get your question but I later figured it out.? TBEACON and possibly SmartBeaconing (variable rate tranmissions) is what you're looking for. --David On 03/04/2025 01:46 PM, Don Rolph via groups.io wrote: toggle quoted message Show quoted text David: from the manual: PBEACON -?for a “position report.” This is generally used for your own location.?It has a fixed position. Later we will discuss TBEACON which gets the location from a GPS receiver. On Tue, Mar 4, 2025 at 4:30?PM David Ranch via <direwolf-groupsio=[email protected]> wrote: Hello Don, If your Direwolf setup has a GPS and you have configured a PBEACON, have you found it's NOT sending the position packets to your IGATE??? Can you show us what you configured for your PBEACON line from the direwolf.conf file as well as the terminal output when you start Direwolf? --David KI6ZHD On 03/04/2025 01:05 PM, Don Rolph via wrote: So I have configured the IGATE servers and logged?in. I would now like to beacon over the iGate port if it is connected over internet. Since I am moving PBEACON?does not seem like it would work. So how does one do this? -- 73, AB1PH Don Rolph -- 73, AB1PH Don Rolph
Don Rolph All Messages By This Member #10357 It was not sending positpons?to the Igate. On a whim I added sendto-IG to the TBECON command. that works but does not?appear to be documented as a possible parameter of TBEACON. toggle quoted message Show quoted text On Tue, Mar 4, 2025 at 4:34?PM David Ranch via <direwolf-groupsio=[email protected]> wrote: [Edited Message Follows] Hello Don, If your Direwolf setup has a GPS and you have configured a TBEACON (not a PBEACON) have you found it's NOT sending the position packets to your IGATE??? Can you show us what you configured for your TBEACON line from the direwolf.conf file as well as the terminal output when you start Direwolf? ? Please note: PBEACONS are intended for static locations.. moving locations use TBEACONs (see the Direwolf User Guide Section 9.11.4 for full details) --David KI6ZHD On 03/04/2025 01:05 PM, Don Rolph via wrote: So I have configured the IGATE servers and logged?in. ? I would now like to beacon over the iGate port if it is connected over internet. ? Since I am moving PBEACON?does not seem like it would work. ? So how does one do this? ? -- ? 73, AB1PH Don Rolph ? -- 73, AB1PH Don Rolph
David Ranch All Messages By This Member #10358 开云体育 Hello Don, I can see how you would say it's not documented as Section 9.11.4 (TBEACON) doesn't have a table like how Sections 9.11.1 (PBEACON and OBEACON) and 9.11.2 (Custom beacons).? If you feel this is an important omission, please create a Github "issue" at so it's not forgotten. --David KI6ZHD On 03/04/2025 02:02 PM, Don Rolph via groups.io wrote: toggle quoted message Show quoted text It was not sending positpons?to the Igate. On a whim I added sendto-IG to the TBECON command. that works but does not?appear to be documented as a possible parameter of TBEACON. On Tue, Mar 4, 2025 at 4:34?PM David Ranch via <direwolf-groupsio=[email protected]> wrote: [Edited Message Follows] Hello Don, If your Direwolf setup has a GPS and you have configured a TBEACON (not a PBEACON) have you found it's NOT sending the position packets to your IGATE??? Can you show us what you configured for your TBEACON line from the direwolf.conf file as well as the terminal output when you start Direwolf? ? Please note: PBEACONS are intended for static locations.. moving locations use TBEACONs (see the Direwolf User Guide Section 9.11.4 for full details) --David KI6ZHD On 03/04/2025 01:05 PM, Don Rolph via wrote: So I have configured the IGATE servers and logged?in. ? I would now like to beacon over the iGate port if it is connected over internet. ? Since I am moving PBEACON?does not seem like it would work. ? So how does one do this? ? -- ? 73, AB1PH Don Rolph ? -- 73, AB1PH Don Rolph

Previous Topic Next Topic