开云体育

I'll be honest.? A lot of us just put in 2 lines with a different comment when sending to IG vs. RF. As you have learned, you don't have to. I have used "sendto" with 2 arguments ((sendto=0,1) for

Okk it looks like: sendto=0,IG does the job. [email protected]> wrote: -- 73, AB1PH Don Rolph

Ok, by adding: sendto=IG to the TBEACON statement, beacons go out over the Igate. But now they never go out over RF. I need the beacons to go out over both RF and the Igate. So it looks like I

Hello Don, I can see how you would say it's not documented as Section 9.11.4 (TBEACON) doesn't have a table like how Sections 9.11.1 (PBEACON and OBEACON) and 9.11.2 (Custom beacons). If you feel

It was not sending positpons to the Igate. On a whim I added sendto-IG to the TBECON command. that works but does not appear to be documented as a possible parameter

Hello Don, I edited my response as I didn't fully get your question but I later figured it out. TBEACON and possibly SmartBeaconing (variable rate tranmissions) is what you're looking

David: from the manual: PBEACON - for a “position report.” This is generally used for your own location. It has a fixed position. Later we will discuss TBEACON which gets the location from a

David Ranch: no I looked in the manual and all the PBEACONS had coordinates configured so I assumed that PBEACONS are static. I sense I may be confused on this point. [email protected]>

Hello Don, If your Direwolf setup has a GPS and you have configured a TBEACON (not a PBEACON) have you found it's NOT sending the position packets to your IGATE??? Can you show us what you

So I have configured the IGATE servers and logged in. I would now like to beacon over the iGate port if it is connected over internet. Since I am moving PBEACON does not seem like it would work. So

Thanks to Thomas KK6FPP and others who have been very helpful.? The reason was that the weather was not being transmitted along with my station info.? A setting on YAAC fixed that and now all is

Hi, It sounds like you figured out the PTT configuration already, but just for reference some additional info: In this particular output from "lsusb" there is not just one USB device that belongs to

Thanks. I am now able to assert ptt with /dev/ttyUSB0. However it does not apear that my transmissions are being digipeated . Too late to do this now. I'll continue

I thought the question was easy enough, but again, what PTT value are you using in your configuration file? Assuming it's named direwolf.conf, in a Linux terminal, type this command: grep "^PTT"

I think I am getting confused.??Are you connecting the DIGIRIG to the TMD710G through the 6-pin miniDIN (Data Jack)?I don't have the DIGIRIG and can't see any information on the cabling. From your

Hi Robert Answering my own question.? This does not work. As you suggested I did lsusb and this is the output Bus 001 Device 004: ID 058f:6387 Alcor Micro Corp. Flash Drive Bus 001 Device 047: ID

Hi Robert This is very helpful. I guessed that tty/USB0 was wrong. But lsusb gave me Bus 1 device 47 as the USB Audio Device but device 47 does not show up in the /dev directory. It shows up in

I don't have a DIGIRIG, but have been running radio applications on Linux for years with various hardware. Not sure how familiar you are with it, so start from thye basics. Since you are using

Hi Rusty This is the first time I am connecting the digirig and my radio.? I have left the serial part as I had it with the kenwood cables which is probably wrong.? That is /dev/ttyUS0.? This is

Hi K6EF I am using the black cable into the audio port as you have and this is working because my receive works fine.? What do you use in the config file for PTT?? What I have right now for PTT is