开云体育

Greetings, I am looking to power up a radio, send a packet, shutdown radio. I had this function on the ArgentData trackers. I am not seeing a reference to this option in the documentation but then I

No need to use ALC input, better not actually... Having a good solution, preferably in software, with PTT interlock and DCD sharing across some channels will do the job. No need to involve any ALC

How about using the ALC input ?

Hi all, I'm about to implement and test with the TRANSMIT INHIBIT INPUT too for some special purpose. For success it's imported it queues the frames and TX-es them when the TXINH input is released.

That looks very nice Craig and some of your other projects on Github look pretty interesting as well! Thanks for posting those. --David KI6ZHD

I have used Direwolf on Pis and never seen this message with GPIO, or VOX. Since this was a slightly different installation of my client, I looked through my APRS client to see if there were any

Audacity and or AlsaMixer are relative readings, similar to an uncalibrated S-meter.You can read the manuals and know what the radio is outputting - especially when using the radio's data jack.? They

if anyone is interested, https://www.youtube.com/watch?v=NJ_IJNU7NA0&t=7s https://github.com/craigerl/direwatch

You can buy the Fe-Pi designed HAT from the new design owners below: https://wb7fhc.com/about-the-fe-pi.html --David KI6ZHD

Direwolf is really very forgiving on RX levels but the general guidance is that it's average receive level is around 50. I can't comment on how the alsamixer setting might look within in a zoomed in

Ok.. that takes the iffy Raspberry Pi USB stack out of the running. When no PTT is configured, it's assume you're using VOX or using a sound device like a Signalink that asserts PTT for you. Per the

The error came on a older x86_64 KUbuntu desktp homebrew computer, with the motherboard sound card, and no PTT setting (VOX).? Direwolf has "no clue' how the PTT is being handled. In fact, the

Hello Alejandro, I would recommend to start with confirming that your HT can hear your Direwolf station (XE1GNU-1) beacons. Per your configuration, those beacons should be sent every 5 minutes. Is

Hello Rob, If you google the following term: direwolf "Transmit timing error: PTT is on" "mSec too long" You'll see a few hits and one one of these talks about the issue being known on non-Raspberry

I used the config file you proposed and it appears to be behaving now. I am getting an error 1.7-dev-A that is????? Transmit timing error: PTT is on 104 mSec too long.? I am using VOX (no PTT

I bumped into this when trying to run two separate instances of direwolf. One for VHF and one for HF. In that case I would see a collision on port 8001. After digging around a bit I found that the way

Hello Roger, Ok.. and btw, I've created a Github issue to track this issue for you: https://github.com/wb2osz/direwolf/issues/342 --David KI6ZHD

In addition, I connected both TCP ports using APRSIS32 [0L] KB8RCO-2>APWW11,WIDE1-1,WIDE2-1:@173559h4209.35N/08346.30W1 EXPERIMENTATION[1L] KB8RCO-2>APWW11,WIDE1-1,WIDE2-1:@173559h4209.35N/08346.30W1

I just compiled V1.7 and tried to change the TCP KISS port.As stated, the 'default' port does not change, however when specifying a port, it looked like this: Dire Wolf DEVELOPMENT version 1.7 A

Thanks, David I did revert to 1.6 stable version and all is well.? Just thought I'd give the new beta a spin- Appreciate your reply and confirmation. Roger, N1XP