开云体育

Hate to beat a dead horse here…I know that these have been discussed ad nausea. Has anyone had any experience with the 32” model Samsung Frame TV? I’ve had pretty good results with all of the other models via Ex-link but for some reason the 32” model cannot be turned on. All the other commands in use on other Frame models work fine except for the power on command. I thought I had it solved as it responded to WOL but after a short while that also stops working. The IP module also gives the same results…works fine then will no longer power on. Something is going to sleep and it seems to be specific to the 32” model. Also, on a slightly different note, the Samsung IP 1.3 from the store has that Newtonsoft requirement that was a “thing” recently…any fix for that?

Hello, Here's my issue: I have an old ViewSonic PRO-8100 connected via RS-232 (port 2) which controlled the power off & on, showed me the lamp hours on my touch panels (Projector on...Lamp hours: 105) through a user module when the MC3 was connected (which I still have). Now I have a CP3 installed and the message on the touch panel says Projector on...Lamp Hours: 0 but the power off & on still functions (still RS-232 port 2), so the CP3 isn't seeing the lamp hours information. Is there a difference in the way that the serial ports receive data between the MC3 and the CP3? Donald

I know these are not the most respected pieces of hardware. I picked one up from surplus and finally got around to playing with it. I can access it through toolbox but I don't have the username and password. It has the 2.0 firmware. The default admin/admin does not work. A hard reset only resets the DHCP. I have been checking around and there doesn't seem to be a way to do a hard reset. The other NVX units have at least a process albeit long one to do a hard reset (11 times pressing reset). Someone on Reddit says there is a way to through a USB drive. I don't have access to that program. Any thoughts? I know there will be a lot of folks that say it is not worth the trouble.

Hi All, I have a site with some CHV stats, most with RTS/RTHS remote sensors. We think that we have seen issues with display offsets. We had set offsets ~ 1-2 year ago to compensate for variances. The MBath unit had a 6 degree offset. unfortunately, the client went thru the winter with uncomfortable environment, and now we find that we need to eliminate the 6 degree offset to make thing right. We're sure that our setting were correct when we did the offsets. Have any others seen the remote sensors need offsets and then have the system need to revert back to no offset? TIA!

Programmer: Pulse Group I found a "Pulse Group" in Vegas who may have done it...waiting to hear from them. Based on what I can tell, this was probably a template used on a ton of jobs. Slot1: SourceFile : W:\Egnyte\Shared\Source Code\NTA_Main\NTA_SUB\FF-NY\Program\v2.0\NTA-FFNY-PP-v2.0 ProgramFile : NTA-FFNY-PP-v2.0.smw SystemName : Lot8 Programmer : Pulse Group CompiledOn : 8/13/2019 4:45 PM Slot2: SourceFile : W:\Egnyte\Shared\Source Code\NTA_Main\NTA_SUB\FF-NY\Program\NTA-FF-NY-SLOT2-ATV_V1 ProgramFile : NTA-FF-NY-SLOT2-ATV_V1.smw SystemName : LOT8 ATV Programmer : Pulse Group CompiledOn : 11/7/2017 8:16 AM

Hi All Is there a way to REMOTELY (VPN) change which SSID a TSR is connected to? I've looked in Console help, the ToolBox function list and the web page. Could it actually be that Crestron expects me to drive 3.5 hours one-way to change the SSID on a remote??? (Probably...:( ) TIA

Does anyone having Simpl windows module for Poly G62

Hi all, i'm looking for a module to control ADA Suite 8x8, but I believe the Suite 16 module will work. We were a ADA dealer, but unfortunately they are no longer in business. Any help would b greatly appreciated.

Recently my Sonos port and connect required a reset to factory settings. While the Sonos connect no longer displayed on our touch panels, the Sonos port would. We kept the Sonos connect because we rarely listen to two different stations in our home and we already owned it, so we use the Port as our main player and the connect as a back up. after resetting the units to factory default, Crestron Home cannot connect to them. It seems them on the network but gives me an error in diagnostics that the “desired household is not found”. I see the household name on the diagnostic screen in the Cresteon home App. However I do not know how to reset the name either on the Sonos or the Home app so they match I deleted the connect from my devices thinking I could just rescan and add it back, but the Home App will not allow me to add the connect. I have been reluctant to remove the SonosPort because even though I can’t see it on the touch panel and the panel states it’s “offline” I am able to listen to my sonos in my house because I just control the Sonos with the Sonos app on my phone I’ve read the Cresteon Sonos troubleshooting guide which actually has this exact error in the document, but I am unable to reconnect the Sonos regardless any insight would be greatly appreciated. ty james

Hello, I'd like to build a project to run on Crestron Go for Ipad to control Crestron Procise PSPHD. Does anyone here have a Crestron Procise PSPHD and Crestron Go on an Ipad to control? I've recently installed a Crestron Procise PSPHD in my home theatre. I have Toolbox, Simpl Windows, VT-Pro but not Smart Graphics or Flash. I have A RMC3 controller I can see the devices in Toolbox I've been advised there may be a template for the Procise PSPHD for VT-Pro to use for Crestron App and X-Panel. Does anyone know if this is true? With thanks

Hello all, I have been using a Send mail V02 module on port 2525. But I am being told that port2525 is a security risk and the network guys we work with started blocking both 25 and 2525 so I need an alternate way to send emails to our team for things like high Temperatures. What are you guys using that is secure to send emails from a CP4/PRO4 ? Thank you, Jon

Garage overhead doors are a common entry point into a home for burglars. With this in mind, a smart garage controller that is integrated with an overall smart home, can provide both convenience and added security. My latest article looks at several smart garage door controller systems and their integration into the smart home. You can find the article here: https://restechtoday.com/integrating-modern-overhead-garage-doors-with-your-smart-home/ For those interested in earlier articles that I've written, you can find those here: https://restechtoday.com/author/jaybasen/ For these interested in even earlier content that I wrote, you can find it all here though older content has formatting issues due to a transfer from blogspot to wordpress. https://topicsinhomeautomation.wordpress.com/ Thanks

I am in the process of replacing some older Control 4 systems with Crestron Home using the CP4-R processsor and other goodies as required. One stumbling block is a few of these clients have the Control 4 video chime doorbell installed and the clients do not want to lose the integration with the distributed audio system as far as ducking and ringing through the audio distribution matrix. Does anyone out there have a recommendation on how to integrate the chime doorbell with Crestron Home and DM-NAX? If not, is there a replacement chime doorbell from another vendor that would? Thanks in advance.

I have both VMS and IPC 4100's and they do respond to IR but occasionally flakey. Is there protocol available to control them via IP?

I searched this forum and couldn't find any info; forgive me if I missed it. We have used audio levels to trigger camera presets many times. Of course, discreet mics work pretty well for this, ceiling mics not so well. The Shure MXA mics seem to have the potential to make this simple, but I haven't found the secret yet. Viewing the lobes in Shure Designer, I can see that the correct/expected lobe is activated immediately - it appears to be flawless. But Shure's command strings don't offer a simple Get Beam Activated. Instead, they offer "Get X-Axis Beam Steering, Get Y-Axis, and Get Beam Height (Z-Axis), all measured in centimeters from the mic. I don't need, and can't use, this extreme level of detail and the resultant flood of signals to parse. Extron offers a way to pre-define a 3-dimensional cube by defining the X, Y, and Z coordinates of its imaginary diagonal corners in a space, and then notify me when the X, Y, Z coordinates being reported fall within a defined cube. This is a tedious and sometimes confusing process, but it seems to work. However, even then, I only get a notice that a zone has been activated; it does not report that the activation has ceased - which is a critical piece of information. It seems to me, though, that this requires me to re-invent the wheel, when that parsing and comparing of data points is clearly already happening within either the mic itself or the Shure Designer software, because I see the lobes firing (or highlighting) accurately in the software. It seems that when I drag a lobe to a specific coverage area, that is graphically defining the 3-dimensional space, and Shure is already calculating which lobe a given audio source falls in. Why not simply make that info available via command string? i.e. is a lobe active?... which one? Will someone please show me what a dolt I am, or possibly point me to a module or other useful solution?

Is there any way inside a SIMPL module to know if any of it's input signals are connected in the root program? For example I have a module with 10 input signals and 10 output feedback signals. I want all of the feedback signals to go high at the same time but only for the signals that have connected inputs. Is this possible?

I have a weird situation where one method in a simpl# module won’t write to the console. for argument sake. Public string test() { CrestronConsole.PrintLine(“Hello World”); Return (“Success"); } I know that the method is being successfully called from simpl+ because it returns the string and that is seen by simpl+. But the Hello World doesn’t show in toolbox. the strange thing is that every other method in the simpl# code will show message when printed to the console.

I am having a rash of HR-310s that the batteries are corroding within a very short time period, before the batteries die. This causes the remotes to not power up from batteries. Anyone else seeing this?

Hi all. Just wondering if anyone knows of any IP intercoms/access control systems out there that might integrate well with Crestron? I currently use 2N IP Verso (gen1) and a couple of access control units (keypads) which do everything I want in terms of integrating with my Crestron but the thing that is killing me is the video quality of the door camera. Its horrible. Low res, grainy and unusable at night. I am also not a big fan of the 2N licensing structure and having to pay extra for this and extra for that and even just the subscription cost to have it call our phones. Ultimately I wanted 2N for the ability for the intercom to be used on our TSW panels but as it turns out, we just dont use that feature. When the doorbell rings, one of us has answered it on our phone before getting anywhere near a TSW! Im looking for something that can provide a higher quality image, with the ability to add access control units to the system, and there are a few options out there, but I need the ability to control the units IO ports via an API through Crestron at the same time. I use this for door locking/unlocking from Crestron and also door open/close monitoring among a few other things. Hikvision do a very similar system to the 2N which ticks all the boxes, but as far as I know, their API is non existent so I would lose Crestron control. Have also seen another brand called Akuvox which looks interesting and they seem to have control support for their devices, but I am just unfamiliar with the brand. I could always upgrade to the 2N IP Verso 2.0 but again, their prices are ridiculous and then add on the required automation licenses and ongoing subscription costs for each mobile device and it becomes a rather unattractive option. Any thoughts or recommendations? Or am I looking for a fairytale project that just doesnt exist in the price range of common folk?

Does anyone have the specs on how to control a TCL display via IP? It's their new 115" display. I can turn it on via WOL, but I can't find anything else on it's IP control. I've spoken to their tech support, and tier two took all my contact information and I never heard back. All I need is power off and inputs. TIA