|
Can anyone recommend an ST-IO alternative. I have 30+ shade motors(LV UP,DN,STOP) that currently have PLC interfaces that are being replaced and integrated into a new crestron system.
|
CNX-RY16 cards in a 2 series or C3RY16 cards in a Pro3/AV3+Cage/C3CI card interface?
Lincoln
--
Lincoln King-Cliby, CTS
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Silver)
V: 440.449.1100 x1107 F: 440-449-1106 I:
Crestron Services Provider
toggle quoted message
Show quoted text
-----Original Message-----
From: Crestron@... [mailto:Crestron@...] On Behalf Of muham41
Sent: Thursday, August 15, 2013 12:39 PM
To: Crestron@...
Subject: [Crestron] ST-IO Alternative
Can anyone recommend an ST-IO alternative. I have 30+ shade motors(LV UP,DN,STOP) that currently have PLC interfaces that are being replaced and integrated into a new crestron system.
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
|
CNPI-48 or 2 CNPI-16. Intended for custom button panels, but it is basically an i/o.
Davis
________________________________
CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
|
Careful that thing is a nightmare to wire. CNPI-48
From: Davis Whitehurst <whitehurstd@...<mailto:whitehurstd@...>>
Reply-To: "Crestron@...<mailto:Crestron@...>" <Crestron@...<mailto:Crestron@...>>
Date: Thursday, August 15, 2013 1:29 PM
To: "Crestron@...<mailto:Crestron@...>" <Crestron@...<mailto:Crestron@...>>
Subject: [Crestron] Re: ST-IO Alternative
CNPI-48 or 2 CNPI-16. Intended for custom button panels, but it is basically an i/o.
Davis
________________________________
CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
[Non-text portions of this message have been removed]
|
Sorry....forgot to mention. The shades are in groups of 6-7 in remote locations w/a single cat 5 available for interface with control system. spec'd a couple of the ST-IO's but was wondering about an alternative. No lutron availble for CCI.
toggle quoted message
Show quoted text
--- In Crestron@..., Lincoln King-Cliby <lincoln@...> wrote:
CNX-RY16 cards in a 2 series or C3RY16 cards in a Pro3/AV3+Cage/C3CI card interface?
Lincoln
--
Lincoln King-Cliby, CTS
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Silver)
V: 440.449.1100 x1107 F: 440-449-1106 I:
Crestron Services Provider
-----Original Message-----
From: Crestron@... [mailto:Crestron@...] On Behalf Of muham41
Sent: Thursday, August 15, 2013 12:39 PM
To: Crestron@...
Subject: [Crestron] ST-IO Alternative
Can anyone recommend an ST-IO alternative. I have 30+ shade motors(LV UP,DN,STOP) that currently have PLC interfaces that are being replaced and integrated into a new crestron system.
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
|
So, your saying that it operates similar to a versa-port, providing contact closure?
toggle quoted message
Show quoted text
--- In Crestron@..., Seth Olle <seth@...> wrote:
Careful that thing is a nightmare to wire. CNPI-48
From: Davis Whitehurst <whitehurstd@...<mailto:whitehurstd@...>>
Reply-To: "Crestron@...<mailto:Crestron@...>" <Crestron@...<mailto:Crestron@...>>
Date: Thursday, August 15, 2013 1:29 PM
To: "Crestron@...<mailto:Crestron@...>" <Crestron@...<mailto:Crestron@...>>
Subject: [Crestron] Re: ST-IO Alternative
CNPI-48 or 2 CNPI-16. Intended for custom button panels, but it is basically an i/o.
Davis
________________________________
CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
[Non-text portions of this message have been removed]
|
Sounds like 3-4 GLS-SIM's would do the trick nicely.
toggle quoted message
Show quoted text
--- In Crestron@..., "muham41" <muham41@...> wrote:
Sorry....forgot to mention. The shades are in groups of 6-7 in remote locations w/a single cat 5 available for interface with control system. spec'd a couple of the ST-IO's but was wondering about an alternative. No lutron availble for CCI.
--- In Crestron@..., Lincoln King-Cliby <lincoln@> wrote:
CNX-RY16 cards in a 2 series or C3RY16 cards in a Pro3/AV3+Cage/C3CI card interface?
Lincoln
--
Lincoln King-Cliby, CTS
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Silver)
V: 440.449.1100 x1107 F: 440-449-1106 I:
Crestron Services Provider
-----Original Message-----
From: Crestron@... [mailto:Crestron@...] On Behalf Of muham41
Sent: Thursday, August 15, 2013 12:39 PM
To: Crestron@...
Subject: [Crestron] ST-IO Alternative
Can anyone recommend an ST-IO alternative. I have 30+ shade motors(LV UP,DN,STOP) that currently have PLC interfaces that are being replaced and integrated into a new crestron system.
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
|
If you are replacing PLC units your best possible form factor is probably the DIN-8SW8 in a DIN rail panel. C3RY-16 cards could be put into a 3 slot cage, but that will probably cost a lot more. Mark On Thu, Aug 15, 2013 at 12:38 PM, muham41 <muham41@...> wrote: **
Can anyone recommend an ST-IO alternative. I have 30+ shade motors(LV
UP,DN,STOP) that currently have PLC interfaces that are being replaced and
integrated into a new crestron system.
[Non-text portions of this message have been removed]
|
whoops, you want the contact closures. A couple of C2N-IO's might be best then...
toggle quoted message
Show quoted text
--- In Crestron@..., "robbie_ray" <rlray@...> wrote:
Sounds like 3-4 GLS-SIM's would do the trick nicely.
--- In Crestron@..., "muham41" <muham41@> wrote:
Sorry....forgot to mention. The shades are in groups of 6-7 in remote locations w/a single cat 5 available for interface with control system. spec'd a couple of the ST-IO's but was wondering about an alternative. No lutron availble for CCI.
--- In Crestron@..., Lincoln King-Cliby <lincoln@> wrote:
CNX-RY16 cards in a 2 series or C3RY16 cards in a Pro3/AV3+Cage/C3CI card interface?
Lincoln
--
Lincoln King-Cliby, CTS
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Silver)
V: 440.449.1100 x1107 F: 440-449-1106 I:
Crestron Services Provider
-----Original Message-----
From: Crestron@... [mailto:Crestron@...] On Behalf Of muham41
Sent: Thursday, August 15, 2013 12:39 PM
To: Crestron@...
Subject: [Crestron] ST-IO Alternative
Can anyone recommend an ST-IO alternative. I have 30+ shade motors(LV UP,DN,STOP) that currently have PLC interfaces that are being replaced and integrated into a new crestron system.
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
|
CNPI gotcha is that they don't work on a 3 series. At least the 16 doesn't. Either one of the inputs or outputs didn't work when we used them with a Harry Joseph Hushbutton system and had to put in DIN-AP2s just for the CNPI units. Mark On Thu, Aug 15, 2013 at 1:29 PM, Davis Whitehurst <whitehurstd@...>wrote: **
CNPI-48 or 2 CNPI-16. Intended for custom button panels, but it is
basically an i/o.
Davis
________________________________
CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files
or previous e-mail messages attached to it, may contain confidential
information that is legally privileged. If you are not the intended
recipient, or a person responsible for delivering it to the intended
recipient, you are hereby notified that any disclosure, copying,
distribution or use of any of the information contained in or attached to
this message is STRICTLY PROHIBITED. If you have received this transmission
in error, please immediately destroy the original transmission and its
attachments without reading them or saving them to disk. Thank you.
[Non-text portions of this message have been removed]
|
CEN-CI3-1 with CEN-IO16s On 2013-08-15, at 1:10 PM, "robbie_ray" <rlray@...> wrote: whoops, you want the contact closures. A couple of C2N-IO's might be best then...
--- In Crestron@..., "robbie_ray" <rlray@...> wrote:
Sounds like 3-4 GLS-SIM's would do the trick nicely.
--- In Crestron@..., "muham41" <muham41@> wrote:
Sorry....forgot to mention. The shades are in groups of 6-7 in remote locations w/a single cat 5 available for interface with control system. spec'd a couple of the ST-IO's but was wondering about an alternative. No lutron availble for CCI.
--- In Crestron@..., Lincoln King-Cliby <lincoln@> wrote:
CNX-RY16 cards in a 2 series or C3RY16 cards in a Pro3/AV3+Cage/C3CI card interface?
Lincoln
--
Lincoln King-Cliby, CTS
Commercial Market Director
Sr. Systems Architect | Crestron Certified Master Programmer (Silver)
V: 440.449.1100 x1107 F: 440-449-1106 I:
Crestron Services Provider
-----Original Message-----
From: Crestron@... [mailto:Crestron@...] On Behalf Of muham41
Sent: Thursday, August 15, 2013 12:39 PM
To: Crestron@...
Subject: [Crestron] ST-IO Alternative
Can anyone recommend an ST-IO alternative. I have 30+ shade motors(LV UP,DN,STOP) that currently have PLC interfaces that are being replaced and integrated into a new crestron system.
------------------------------------
Check out the Files area for useful modules, documents, and drivers.
A contact list of Crestron dealers and programmers can be found in the Database area.
Yahoo! Groups Links
[Non-text portions of this message have been removed]
|
Victor D