开云体育

Debugger and 4-series

ckangis All Messages By This Member #242531 Is it just the site I'm working with or is Debugger noticeably slower/More sluggish (Iknow, I know...) with 4-series. I'm running a CP4 with v2.6 FW
jbasen All Messages By This Member #242532 I haven’t personally noticed it being slower but I have run into problems with the debugger losing its connection with the control system Jay toggle quoted message Show quoted text On Wed, Aug 11, 2021 at 6:38 PM ckangis <chris@...> wrote: Is it just the site I'm working with or is Debugger noticeably slower/More sluggish (Iknow, I know...) with 4-series. I'm running a CP4 with v2.6 FW
MSTC All Messages By This Member #242533 开云体育 There is an automatic disconnect after 20 minutes.? I saw a console command to adjust the time out but I can’t remember it right now.? I think setting it to 0 would make it never disco. ? I haven’t personally noticed it being slower but I have run into problems with the debugger losing its connection with the control system ? Jay ? toggle quoted message Show quoted text On Wed, Aug 11, 2021 at 6:38 PM ckangis <chris@...> wrote: Is it just the site I'm working with or is Debugger noticeably slower/More sluggish (Iknow, I know...) with 4-series. I'm running a CP4 with v2.6 FW
jbasen All Messages By This Member #242534 Thanks.? Good to know. However, I’ve seen some ?disconnects much faster than 20 minutes? Jay toggle quoted message Show quoted text On Wed, Aug 11, 2021 at 7:49 PM MSTC <kol.mstc@...> wrote: There is an automatic disconnect after 20 minutes.? I saw a console command to adjust the time out but I can’t remember it right now.? I think setting it to 0 would make it never disco. ? I haven’t personally noticed it being slower but I have run into problems with the debugger losing its connection with the control system ? Jay ? On Wed, Aug 11, 2021 at 6:38 PM ckangis <chris@...> wrote: Is it just the site I'm working with or is Debugger noticeably slower/More sluggish (Iknow, I know...) with 4-series. I'm running a CP4 with v2.6 FW
Robert Herrick All Messages By This Member #242535 I just noticed that the header for this topic mentions 4-Series, so this might not apply exactly. I had this “debugger time out” concern when working with my CP3 on my test bench. TB pointed me to this area to make the adjustment: Open Toolbox, then Device Discovery, connect to the processor, select the FUNCTIONS button, select Authentication, then select Authentication Options. There is a box on that page to specify the “Default User Idle Time”; set as desired or select NO IDLE LIMIT (my choice). Please advise if this helps or applies to the ?4 series ,as I have not used one of those so far.
Steve Kuehn All Messages By This Member #242536 On Wed, Aug 11, 2021 at 08:49 PM, MSTC wrote: There is an automatic disconnect after 20 minutes.? I saw a console command to adjust the time out but I can’t remember it right now.? I think setting it to 0 would make it never disco. ? I haven’t personally noticed it being slower but I have run into problems with the debugger losing its connection with the control system The console command you are looking for is: SETLogoffidletime 0 Haven't tried it with SIMPL debugger yet.? However, a few days ago, I was ssh into a CP4 all day (no Crestron software involve) and had no disconnects.? Before I issued the above command via an SSH connection, the CP4 was constantly disconnecting. YMMV, Steve
Thorsten K?hler All Messages By This Member #242540 开云体育 ?However, I’ve seen some ?disconnects much faster than 20 minutes?“ Yep, same here. ? Cheers, Thorsten ? Von: [email protected] <[email protected]> Im Auftrag von jbasen Gesendet: Donnerstag, 12. August 2021 03:59 An: [email protected] Betreff: Re: [crestron] Debugger and 4-series ? ? Thanks.? Good to know. ? However, I’ve seen some ?disconnects much faster than 20 minutes? ? Jay ? toggle quoted message Show quoted text On Wed, Aug 11, 2021 at 7:49 PM MSTC <kol.mstc@...> wrote: There is an automatic disconnect after 20 minutes.? I saw a console command to adjust the time out but I can’t remember it right now.? I think setting it to 0 would make it never disco. ? I haven’t personally noticed it being slower but I have run into problems with the debugger losing its connection with the control system ? Jay ? On Wed, Aug 11, 2021 at 6:38 PM ckangis <chris@...> wrote: Is it just the site I'm working with or is Debugger noticeably slower/More sluggish (Iknow, I know...) with 4-series. I'm running a CP4 with v2.6 FW
jbasen All Messages By This Member #242551 开云体育 Thanks Steve.? I just checked my CP4 and when I type in the console command the response is: Logoff Idle Time (minutes): infinite Jay On 8/11/2021 9:46 PM, Steve Kuehn wrote: toggle quoted message Show quoted text On Wed, Aug 11, 2021 at 08:49 PM, MSTC wrote: There is an automatic disconnect after 20 minutes.? I saw a console command to adjust the time out but I can’t remember it right now.? I think setting it to 0 would make it never disco. ? I haven’t personally noticed it being slower but I have run into problems with the debugger losing its connection with the control system The console command you are looking for is: SETLogoffidletime 0 Haven't tried it with SIMPL debugger yet.? However, a few days ago, I was ssh into a CP4 all day (no Crestron software involve) and had no disconnects.? Before I issued the above command via an SSH connection, the CP4 was constantly disconnecting. YMMV, Steve
j5races All Messages By This Member #242553 PRO4>SETLogoffidletime 0 Logoff Idle Time CHANGED: infinite Thats what my PRO4 also responded with. My PRO3 didn't give any response when the same command was sent.

Previous Topic Next Topic