开云体育

Samsung ME55B IP Control Issue

dragula63 All Messages By This Member #172734 I can connect to it. Change inputs, adjust volume, etc. However when I turn it off I can't turn it back on because the ethernet port is dead when the TV is off. Any ideas how to enable the ethernet port when the TV is off. Thanks Corey
hitplay07 All Messages By This Member #180474 Hi Corey, Did you ever figure this one out? I am having the exact same issue. When I ping the port while the display is off there is no response. There must be some way to keep it active while the display is off. Thanks, Eric toggle quoted message Show quoted text --- In Crestron@..., cchurch@... wrote: I can connect to it. Change inputs, adjust volume, etc. However when I turn it off I can't turn it back on because the ethernet port is dead when the TV is off. Any ideas how to enable the ethernet port when the TV is off. Thanks Corey
mlafayette2350 All Messages By This Member #180501 There is info on this board about using the Wake on LAN feature on these TVs. I've got it working here at my shop. Use WoL to turn the display on, then you can go from there. Works well. Mike toggle quoted message Show quoted text --- In Crestron@..., cchurch@... wrote: I can connect to it. Change inputs, adjust volume, etc. However when I turn it off I can't turn it back on because the ethernet port is dead when the TV is off. Any ideas how to enable the ethernet port when the TV is off. Thanks Corey
MSTC All Messages By This Member #180514 If there is a panel off command, that shuts off the backlight but leaves the unit on . . . _____ From: Crestron@... [mailto:Crestron@...] On Behalf Of hitplay07 Sent: Thursday, June 06, 2013 7:09 AM To: Crestron@... Subject: [Crestron] Re: Samsung ME55B IP Control Issue Hi Corey, Did you ever figure this one out? I am having the exact same issue. When I ping the port while the display is off there is no response. There must be some way to keep it active while the display is off. Thanks, Eric --- In Crestron@... <mailto:Crestron%40yahoogroups.com> , cchurch@... wrote: I can connect to it. Change inputs, adjust volume, etc. However when I turn it off I can't turn it back on because the ethernet port is dead when the TV is off. Any ideas how to enable the ethernet port when the TV is off. Thanks Corey
ix_kool All Messages By This Member #182647 Hello ! Is there a way to perform WoL thru DIN-AP2 or CP2E ? Using TCP CLIENT ? Thank you, Francois-Xavier G. toggle quoted message Show quoted text --- In Crestron@..., "mlafayette2350" <michael.lafayette@...> wrote: There is info on this board about using the Wake on LAN feature on these TVs. I've got it working here at my shop. Use WoL to turn the display on, then you can go from there. Works well. Mike --- In Crestron@..., cchurch@ wrote: I can connect to it. Change inputs, adjust volume, etc. However when I turn it off I can't turn it back on because the ethernet port is dead when the TV is off. Any ideas how to enable the ethernet port when the TV is off. Thanks Corey
Jeremy Weatherford All Messages By This Member #182654 Yes, there's a module in the Files section here. You'll use a UDP Communications "device" to send the WoL magic packet. toggle quoted message Show quoted text On Mon, Jul 22, 2013 at 6:12 AM, ix_kool <ix_kool@...> wrote: Hello ! Is there a way to perform WoL thru DIN-AP2 or CP2E ? Using TCP CLIENT ? Thank you, Francois-Xavier G. --- In Crestron@..., "mlafayette2350" <michael.lafayette@...> wrote: There is info on this board about using the Wake on LAN feature on these TVs. I've got it working here at my shop. Use WoL to turn the display on, then you can go from there. Works well. Mike --- In Crestron@..., cchurch@ wrote: I can connect to it. Change inputs, adjust volume, etc. However when I turn it off I can't turn it back on because the ethernet port is dead when the TV is off. Any ideas how to enable the ethernet port when the TV is off. Thanks Corey ------------------------------------ Check out the Files area for useful modules, documents, and drivers. A contact list of Crestron dealers and programmers can be found in the Database area. Yahoo! Groups Links -- Jeremy Weatherford
papazex All Messages By This Member #184338 Hallo can you tell me the TCP port and module you use to control the TV? toggle quoted message Show quoted text --- In Crestron@..., Jeremy Weatherford <jweather@...> wrote: Yes, there's a module in the Files section here. You'll use a UDP Communications "device" to send the WoL magic packet. On Mon, Jul 22, 2013 at 6:12 AM, ix_kool <ix_kool@...> wrote: Hello ! Is there a way to perform WoL thru DIN-AP2 or CP2E ? Using TCP CLIENT ? Thank you, Francois-Xavier G. --- In Crestron@..., "mlafayette2350" <michael.lafayette@> wrote: There is info on this board about using the Wake on LAN feature on these TVs. I've got it working here at my shop. Use WoL to turn the display on, then you can go from there. Works well. Mike --- In Crestron@..., cchurch@ wrote: I can connect to it. Change inputs, adjust volume, etc. However when I turn it off I can't turn it back on because the ethernet port is dead when the TV is off. Any ideas how to enable the ethernet port when the TV is off. Thanks Corey ------------------------------------ Check out the Files area for useful modules, documents, and drivers. A contact list of Crestron dealers and programmers can be found in the Database area. Yahoo! Groups Links -- Jeremy Weatherford [Non-text portions of this message have been removed]
[email protected] All Messages By This Member #188321 Im trying to connect to a samsung 75me via ethernet. I try to make a tcp\ip connection, but I cant find any documentation on the ethernet protocol, ports ect. Can anyone guide me in the right direction? Thanks. ---In crestron@..., <zex27@...> wrote: Hallo can you tell me the TCP port and module you use to control the TV? toggle quoted message Show quoted text --- In Crestron@..., Jeremy Weatherford <jweather@...> wrote: > > Yes, there's a module in the Files section here. You'll use a UDP > Communications "device" to send the WoL magic packet. > > > On Mon, Jul 22, 2013 at 6:12 AM, ix_kool <ix_kool@...> wrote: > > > > > Hello ! > > > > Is there a way to perform WoL thru DIN-AP2 or CP2E ? Using TCP CLIENT ? > > > > Thank you, > > > > Francois-Xavier G. > > > > --- In Crestron@..., "mlafayette2350" <michael.lafayette@> > > wrote: > > > > > > There is info on this board about using the Wake on LAN feature on these > > TVs. I've got it working here at my shop. Use WoL to turn the display on, > > then you can go from there. Works well. > > > > > > Mike > > > > > > --- In Crestron@..., cchurch@ wrote: > > > > > > > > I can connect to it. Change inputs, adjust volume, etc. However when > > I turn it off I can't turn it back on because the ethernet port is dead > > when the TV is off. Any ideas how to enable the ethernet port when the TV > > is off. > > > > > > > > Thanks Corey > > > > > > > > > > > > > > > > > ------------------------------------ > > > > > > > > > > Check out the Files area for useful modules, documents, and drivers. > > > > A contact list of Crestron dealers and programmers can be found in the > > Database area. > > Yahoo! > > Groups Links > > > > > > > > > > -- > Jeremy Weatherford > > > [Non-text portions of this message have been removed] >
mlafayette2350 All Messages By This Member #188326 WOL to wake the display. ?UDP is 40000. TCP port is 1515. ?The Samsung 460UTN-UD Module and Processor have all of your commands. ?Same protocol as the RS232. ---In crestron@..., <stian.aurdal@...> wrote: Im trying to connect to a samsung 75me via ethernet. I try to make a tcp\ip connection, but I cant find any documentation on the ethernet protocol, ports ect. Can anyone guide me in the right direction? Thanks. toggle quoted message Show quoted text ---In crestron@..., <zex27@...> wrote: Hallo can you tell me the TCP port and module you use to control the TV? --- In Crestron@..., Jeremy Weatherford <jweather@...> wrote: > > Yes, there's a module in the Files section here. You'll use a UDP > Communications "device" to send the WoL magic packet. > > > On Mon, Jul 22, 2013 at 6:12 AM, ix_kool <ix_kool@...> wrote: > > > > > Hello ! > > > > Is there a way to perform WoL thru DIN-AP2 or CP2E ? Using TCP CLIENT ? > > > > Thank you, > > > > Francois-Xavier G. > > > > --- In Crestron@..., "mlafayette2350" <michael.lafayette@> > > wrote: > > > > > > There is info on this board about using the Wake on LAN feature on these > > TVs. I've got it working here at my shop. Use WoL to turn the display on, > > then you can go from there. Works well. > > > > > > Mike > > > > > > --- In Crestron@..., cchurch@ wrote: > > > > > > > > I can connect to it. Change inputs, adjust volume, etc. However when > > I turn it off I can't turn it back on because the ethernet port is dead > > when the TV is off. Any ideas how to enable the ethernet port when the TV > > is off. > > > > > > > > Thanks Corey > > > > > > > > > > > > > > > > > ------------------------------------ > > > > > > > > > > Check out the Files area for useful modules, documents, and drivers. > > > > A contact list of Crestron dealers and programmers can be found in the > > Database area. > > Yahoo! > > Groups Links > > > > > > > > > > -- > Jeremy Weatherford > > > [Non-text portions of this message have been removed] >

Previous Topic Next Topic