开云体育

Greetings all .I had an app project working fine .it was local only .suddenly stopped. Says connection refused .I have updated firmware , all data bases still says the same .any ideas ? Its on a pro3

Microsoft released an update which should fix the issue: 2022-05 Cumulative Update for .NET Framework 3.5 and 4.8 for Windows 11 for x64 (KB5013628) -- Crestron Service Provider - TBD Enterprises Inc.

SIMPL+ NVRAM allocation was introduced in CCD Disp Eth v1.14. (F1 Revision History calls out "Added ability to page through more than 10 user attributes.") SIMPL compiler calls out max NVRAM

Well must be a hold over from 2 series in Simpl, crisis averted.? I checked the PRO4 and it actually has 3MB of NVRAM.

Hi there! You would use the feedback signals of the?Lutron HomeWorks QSX Button Control v1.1 module. The outputs of that module will go high when the corresponding physical Lutron keypad button is

Learned a valuable less today.? I am using the Sony IP CCD modules for both TV and Receivers.? Apparently they are NVRAM hungry.? Each CCD allocates about 10KB of NVRAM.? I am just updating a

Thanks for all the advice and suggestions! I ended up doing what Dave H suggested (one of his suggestions) and made my magic packet string in Notepad and copied/pasted into an SIO. I had to put a 1 on

Cool automation and Crestron Home BACnet, YABE We have 1 CoolinkBridge ID 64 showing a HVAC system detailed BACnet data for Thermostat - operation is good in Crestron home? YABE show all BACnet info

I should also add that the Shelly TRV can be fully controlled through the Shelly app. Thanks Jay [email protected]> wrote:

Correct. All Shelly devices communicate directly over WiFi so they don’t require a hub And, the Shelly drivers I’ve written will run on either a 3 or 4 series processor. All the source code is

Hi, first time doing Lutron QSX...I have the HomeWorks QSX v1.1 module from the Application Marketplace and I do not see a way to receive button presses into Crestron from a Lutron keypad. I want to

Hi Jay, many thanks for the info! No, the TRV referred to wasn't a Shelly one, it was old school mechanical with a capilliary tube! I have downloaded your demo files, and have contacted the supplier

https://drivers.crestron.io/rad/driver-search/3913 https://support.crestron.com/app/answers/detail/a_id/1000527 /g/crestron/message/245762

I wasn’t sure from your email if the TRV you refer to is the one recently released by Shelly https://restechtoday.com/shelly-trv-is-smart-home-technology-for-homes-heated-with-radiators/ Hope this

Thanks Dave!! I really appreciate how responsive and on-point you always are...:) I'm going to update the system in question with this tomorrow...

Hi All, we have a project that we did back in 2006 that we are now looking at refurbishing / upgrading. At the time of installation heating consisted of an UFH manifold for the upper floor, and a

https://www.crestron.com/Software-Firmware/Firmware/Other-Products/PC-350V-12_PC-350V-18/3-007-0035-19110 https://www.crestron.com/release_notes/pc-350v-1x_3.007.0035.19110_release_notes.pdf New

This is correct, the App Icons are fed to the panel from the Roku, however, in my experience the Roku will not provide an icon for the local inputs (HDMI 1, 2, 3, 4, TV etc.) so I loaded icons to

the icons come from the roku player

Quick question about this - I just tried to put the Group's Files "Roku 3 Series" and noticed that the icon outputs are string/serial outputs. Are those strings supposed to be file locations of icons