Personally, I would not use a slider and just a gauge for feedback.? To answer you question, look at the difference between an analog and serial buffer.? You need both in this case.??

We set up a large resi system in our factory last year and as some of you may recall I was very happy with NAX.

Now the system is on site (very much a building site still) we have frequent power outages and still no AC in the AV Room.

Each night we power down the AV system down to avoid overheating when we lock the door.
Not something I'm happy about but this has exposed a few NAX issues.

The main one I'm trying to deal with but don't seem to have found a totally reliable solution is stream?initiation and getting the streams to start.

Source requirements are pretty basic:
5 X Sonos. 2 physically connected to one DM-NAX-8ZSA digital inputs, 3 connected to a second?DM-NAX-8ZSA digital inputs.

Last year when we set up at the factory, I simply went into the web UI and under NAX Streams set Auto Initiation on with default port of 5004.
This worked flawlessly at the factory, but since being on site we found the streams were not starting.

I've now implemented logic in simpl to start the streams and turned off Auto Initiation in the web UI.
This has mostly fixed the issue but very occasionally the streams will simply not start on first try.
I can force a stream stop then restart and it will then work.

In the NAX hardware def: Slot-07: DM-NAX-8ZSA —NAX > Slot-01: DM-NAX-8ZSA —TX> Slots-03 & 04:?DM-NAX-8ZSA — TX Source 3 & 4
I have defined the following:
* valid session name
* valid multicast address
* StartStream
* StopStream

I check in logic:
* I get a device ready pulse from Update Status.
* I have a valid multicast address
* Then issue the StartStream through a Truth Table when the above conditions are satisfied.
This logic works flawlessly and the StartStream digital is asserted.

I'm not checking I have a valid session name as this is set at startup & held in an MSP.

Anyone seen any of these issues and can offer any further suggestions?
I would really like to know why Auto Initiation no longer works, as I rather just do away with all the simpl logic.

Cheers

开云体育

Thank you

I have a?OLED65C1PUB control it using the Crestron Certified Drivers using ethernet.

On the online database there's a?OLED97G2PUA Driver that you could try and experiment with!

I'm in the process of honing in my skills which is very small. I'm controlling a C2N-AMP-4x100. What I can't seem to get working correctly is values updating as they should.

Volume buttons run to an Analog Ramp, analog out of that into an analog buffer thats enabled when the selected room is interlocked. Then the output of that runs to the "Room1_Volume" input of the amp symbol, and out of the "Room1_Volume_FB" into the same analog buffer (enabled by room selected Interlock) to pass to analog join 10 (Slider or gauge) to update the position as im holding the volume buttons. I cannot get the values to update on the slider or gauge ive tried both. I can use touch settable and that value will update but it will carry the same value when I select another room.

What is the best way to use one slider, 3 buttons (v+,v-,mute) to update the slider/gauge live, recall the volume levels of each "zone" if I were to switch rooms back and forth and not affect other zones reporting incorrectly?

Any update on the fix for this or word on what exactly isnt working when trying to use the script?

Ive read that it gets confused on which network to use to "phone home" and that the script settings also get wiped whenever the VC-4 gets updated. Not sure if either or both of these are true.
Would using the USB-Offline dongle fix this issue??

We have several projects based around the dual network design Crestron said was possible and find it extremely irritating that it is "no longer supported".

开云体育

If you have non X model, you can get second usb lan adapter (white ) from Crestron and IP what ever you want it. Not supported on X models (anything that has BYOD).

Thanks all

Lucky.? I've got integrators who have been waiting for months.? This is not an easy part to find and unfortunately when they go bad..... you know.

Hi Dave,
That'd be great! I'll take it if its still available...
Please reach out to me directly at:
chris at eicustom dot com

TIA!

I have a Pro2 that's in good shape.? I thought someone on ebay would want it, but after 3 weeks there hasn't been any interest.

Is it of use to anyone here?? It has the ethernet card and a good CF card.? Cover shipping and it's yours.? Seems better than throwing it out.? If no one wants it, it's off to the recyclers.
?- Dave

The 'U' versions are current, so I'd expect that you'll get them...

FYI, I found a friend who had one and was nice enough to help me with it, so I'm good on this one (Phew!!!!)

?Does anyone know if these are even getting shipped? My order update says i am supposed to get some within a month. However I wonder if they even are making them. Thanks

I would also recommend setting up a dedicated SSID for the TSRs at just the 2.4g freq.?
In larger systems with multiple APs, I would also have unique SSIDs on each AP and tie the TSRs to the closest AP to each of them.
They are not designed to be roaming devices...

I agree that this is not excellent in its design...