I'm looking at the Jandy AquaLink 3.1 demo and unzipped the .clz file to see if there is any indication that the SIMPL# source code is available.? But I only saw some DLLs, DAT, manifest, and .config config files.? Unless I am blind (but instead likely just not very smart), nothing I can see looks remotely like source code.? So I am guessing that at least some if not all .clz files are just compile code much like a SIMPL+ .ush file. Could anyone confirm this is the case?

The reason I ask is the demo program has you select between about a dozen different Jandy systems that the client has at various houses.? I like to filter that all out and just present the two systems and functions of interest on the client's iPad.? While I could look for a particular system name. my guess is the names could change or the order they are presented could change.? Hence working with the existing Jandy module would likely be unreliable without presenting all the systems on the client's Crestron App.? They don't like switching between the Crestron App and the Jandy app.

A complicating factor is they want some of the Jandy lights that are use for landscaping to be controlled by their Crestron lighting system when it turns on the Landscape lights at night.? That would require me to switch between two different systems at the same house.? Prior, the client had been using the old RS232 interface box but that apparently is no longer an option.

Working with the existing Jandy modules just seems too unstable to automate the functions desired.? And of course, the internet and cloud servers have to be up for it to work. If I had the source code, I could possible make something more automation friendly.? Of course I would have to learn SIMPL# to do this but I trying to figure out if it is even feasible to do what I want.

Thanks for you insights and suggestions.
Steve

Tray, the MC3 does not support the authentication needed for a gwexer. You will need to take the firmware back in the gwexer

As Mentioned check for CSAuthen on both ends and you may need to run the unlock / unblock User and IP after setting those. Do not rely on Authen info in tool box just run the command have found that on serveral occasions when nothing showed as blocked or locked out but was..

Try connecting with tool box Secondary Console. Or USB if those don't work and you cant find it with wire shark or angy IP only choice I see is try a factory restore.

I bought 2 PRO3's.? One for the main house for a upgrade from a 2 series.? That one was wiped and had no problems connecting.? The second one still has a project on it.
Front panel shows that it has a static address of 192.168.10.2.? I have tried connecting with that and it's host name.? Also device discovery tool doesn't see it.? I tried a 3rd party IP scanner that doesn't see it.? Any thoughts???

开云体育

Seems like rolling back firmware to a pre-Auth version might be the answer.

This does not work for CEN-GWEXER. Trying to find a solution

开云体育

I had same issue with a 4 series. Turned out mine was authentication.

Can't get CEN-GWEX-ER to connect to MC3 control system.?
setup the user as described and it will not connect at all.?
Any ideas apart from rolling back the gateway firmware?

Any advice on getting a stream on the DMPS3 would be greatly appreciated. I set up a stream with a pull link from Restream (rtmp://live.restream.io/pull/play_3132352_366e659ded2fd19a260d), but could not get the DMPS3 to accept it, no matter what settings were changed. However, VLC had no problem with the stream. I'd really like to get this option functioning as part of a video system upgrade in one of our larger theatres. Thanks in advance!

Dan

Edit: I brought everything to my home network and was unsuccessful, eliminating a firewall issue or something else on our network.

Hello,

We have a Crestron Com-3 talking to a series for Somfy SDB networked shades.? When the shades installer hooked up their PC the shades worked flawlessly, but we can't get consistent reliable control.? The PDF for the Crestron module mentions a 120 ohm termination resistor at both ends of the network.? Do we need to add this to the Crestron end or does its 485 already have this type of termination?

I have a client whose old Polk Audio SR-H2000 finally died.? He had the "lifetime" subscription tied to it so tears were shed.? Is there a rack mount tuner with 232 that is currently available?? I'm ready to jump on ebay and look for an C2NTXM if I have too, but streaming is not desired.? He has an MMS, and hates using it for reasons.

Hey CO Cowboy,

I dont see that option on any of my outputs.
Is that only available on a specific RMC?

I am only looking in DM Tools.

The Serena shades are locked to the Caseta platform.

Matt,
On the output settings of the endpoint,? there is a selection to play audio without video, but this requires you load a graphics file (we use our company logo). We haven't had any "select video first" issues since we started doing that.

Hello,
Thought I would post this here as well as TB
I have a DM-NVX D200 and E30 that I am setting up. I plug them both into a network switch at my desk to configure them and update firmware. I have my laptop connected to the same switch. When I run DM NVX tool ( or device discovery) I can only see the E30 listed as devices that are plugged in.
If I connect my laptop directly to the D200 it shows in the DM NVX tool (and device discovery), I can connect to it and upload firmware.
Question is why can't I see both the D200 and E30 in the DM NVX tool when all three devices (D200, E30 and laptop) are connected to the same switch.

Thanks

I thought all shades were clear connect and would work across all current processors

While I haven't tried it, is there an reason why you couldn't ssh into the DM-NVX-360 and get to the text console that way?? I found most Crestron products except for newer version of the CP4R will accept and SSH connection.