Are you working with a 4KZ switcher or a 4k? On the 4kz, the top has been shutdown by the engineers because of security flaws. The "conf output 1 route 1" command works on the 4k but not 4kz. Extron tech support used data viewer to send that command and the 4kz rejected it.

开云体育

Wait so you have the protocol to control that switcher without needing a Crestron controller? Would you mind sharing?

if you have the unit, test with with Putty from you laptop.

the unit i have works on TCP port 23.

Hi Juan,

that is strange. I found a driver in the Crestron application market (for the whole TD-E series), dated back to 2016.
This driver as well states that the communication settings have to be set to serial to make serial control possible.
BTW, this driver uses different commands and states that Toshiba Rx pin is pin 2.

Don't give up (by Peter Gabriel) and good luck with the Toshiba.

Best regards
Crestronfreak55

I wish I had a Crestron processor. I'm using extron processor. :(

开云体育

You add the device to the system configuration in SIMPL windows. Set the ip address for the device in the device settings. Then you load the program to your processor. The device will not register in the ip table. The sync indicators for the inputs is not reliable but control is fairly reliable using the analog joins.

Will it work with UDP? The engineers at Crestron locked tcp port in the 4kz series of switchers.? ?That's what Crestron is telling me.?

I don?t see any of that in the menu of LCD Toshiba

So for the CBD keypads that have the 'Lutron button 6 tax' applied, even though the image will force/show the split button 6 only, you can still program button 6 as normal and your 6-btn/non-split keypads will still work fine.
HTH

That is interesting.
You can try using Extron EDID Manager to create an EDID file or modify an existing one.
There are lots of options, either get someone that is familiar with EDID or use the try and error methode.

Please keep us updated.
Best regards

Crestronfreak55

Hi Juan,

did you enable RS232 in the Menu, Setup, Control and set the proper baudrate?
Afaik, the Toshiba uses Pin 5 for GND, Pin 3 to receive the commands.

Best regards

Crestronfreak55

Yes, but not work

Hi CrestronFreak.??

The Samsung has the ability to rotate the image and stretch if required so sending it a res of 1080*1920 does work, ie, a signal from my laptop running that resolution, but I just don't have that level control over the resolution with the barco system..? They have told me they are working on this feature but it won't be ready for my deadline unfortunately!?

Hi Bambam_101,

using a display in portrait mode is not a matter of EDID. The video signal is still 1920x1080 and the display shows this as received. The orientation cannot be configured in the EDID.
The source needs to rotate the content by 90 degrees, that does the trick.

Best regards
Crestronfreak55

Hi all. Currently doing my first Barco We Connect system and we have a Barco node (Intel nuc) that is connected to a Samsung lcd screen in portrait mode.? Problem is, there is no way to set the output resolution of the Barco node to portrait as it relies on the edid info from the screen which in this case is presenting as 1920x1080.

After lots of searches for edid emulators that will do an edid of 1080x1920, I thought about the possibility of using a TX201-C and loading a custom edid on to it.? Then placing it between the Barco node and the monitor. (using the hdmi loop out of the 201 to feed the screen.)

Having never played around with crestron edid tool before, can anyone advise if this might even be possible? I managed to have a quick look at the edid tool today but nothing jumped out at me as being able to create a completely custom edid.?

Anyone done portrait displays before and come across anything that might help me out?

Cheers

there is a previous thread on thsi

need add "conf" in front

ex: conf output 1 route 1

you can TCP to the unit on port 23. I am using a hd-md4x1-4k-e. The syntax will be?

Just trying to put back the original program like it was before.? Old Cameo for Old Cameo and New Cameo for New Cameo.? ?All 6Btns & 3Btns.? I looked on some old hard drives from jobs back in 2009 and found the file I was looking for. All my keypads have the original text on them and everything.