Would anybody have a module for a Televic audio conferencing system D-CERNO
Thanks

You have to convert the classic layout to Smart Graphics. Open the file from the TPS-4500. in the project tree, right click on the project and choose Covert to Smart Graphics. After that you will probably have to adjust some objects.

Is there a way to reuse existing projects from a TPS-4500 in the Crestron app or do I have to start from scratch with Smart Graphics?? It would be nice if I could and just resize to fit.? Tried opening two projects and drag a page over but it doesn't take.

So when all else fails, strip it all down, do a factory reset, and build it up again..... and well, it worked.??
So as pieces of the system have been delivered I've been adding them to the system, while playing with a couple of different switches, firewalls, network configurations, etc..? I believe along the way certain settings, configuration's, and/or defaults got off and it took restoring all the pieces, and implementing everything all at once did the trick.? I did also make one small tweak to my vlan settings in my firewall as I rebuilt everything its possible that was it as well, but I lean towards the former.? Thanks for everyone's input, I am sure I'll be back with more questions later :)

Sorry, I misread. I like Sony TVs for Google TV experience. I love how they integrate the app into the Home Screen. You don’t have to launch the app every time you want to find content.

Apple TV is my primary option and roku is the secondary for streaming media players. Apple TV has IP control and best playback. Another option for TVs is the native interface/smart TVs. Use an earc extender to get audio back to the receiver if it is a surround zone. You just need control and the drivers should be available.?

HI,

Apologies, got involved in other bits and had a lot of problems with the IR learner.? ? Works on and off for some reason.? ? ? ?So far I have got the following HEX commands from the remote

Other than the one instance/site that I had the issue with, that started this thread I haven't had any real issues with TCP client connections. Things have been very stable on 3 and 4-series...

Note: By default, I start my TCP connections programmatically (i.e. with signal triggers not a '1') after the main program is fully started. This may contribute to more stability, though I do it only for my own feeling of wanting to stage things in an orderly manor, not because I actually found it to be required (though it may actually be...)

Since this topic is being resurrected I’d love to know people’s general thoughts on whether or not the TCP Client, along with other IP issues, has been fixed on 4-series yet.

I still have several issues with:
4-series stopping reconnecting to a port when the connection is remotely dropped even though Connect is tied to 1, requiring a reboot/restart.
4-series to 3-series inter system communication randomly failing.
4-series to TSW-x70 communication stopping.
Ethernet based CCDs that work fine on 3-series failing on 4-series.

In terms of using a S+ emulation of the TCP-Client symbol to work around some issues, is this still recommended? If so, could anyone share a S+ module that can work as a drop-in replacement for the standard TCP Client symbol?

Hi Brandon,?

Because you said manually routing of the NVX works, there shouldn‘t be a network issue.?

?

Pretty sure you didn‘t configure the routes for all sources within all mediazone. You need to tell Home which source is on?

which input of the NVX, which TV or projector is connected to which NVX output. Maybe differently which route should

audio go if it needs to be different. That can be pretty irritating the first time and with some setups.?

?

So go to the Crestron Home setup app, at the bottom bar use the fourth selection, should be source routing.?

Select all rooms with mediasources and mediaoutput and tell Home which sources are connected to which?

inputs and TVs on which NVX outputs. Maybe NVX output first to an AV-Receiver input, and the output of?

the AV-Receiver HDMI out to the TV HDMI in

.?

Select the room for the mediazone, activate the mediazone here you can select which sources should be?

selectable in which mediazone (press and hold you can arrange the source order) and very important mainly

for the audio, go to ?favorite routing“ (maybe the english naming is little different) and tell which audioendpint

to select for which mediasource. These can be different I-Net Radio on NAX speakerout, TV or streamer audio?

to soundbar/TV/av-receiver.

?

With that the system knows how to set the routes when sources are selected and what to control when audio?

level is controlled.?

?

Hopefully this helps…

Yes, I believe that is all set up correct. I’m starting to wonder if it’s an IGMP issue. I’m running an older x440 g2 on older firmware. I’ve enabled IGMP and the quierer but I’m not confident it’s running as it should. I’ve got a netgear 4250 on order. ?If IGMP is not running as it should im
just wondering if the processor isn’t establishing the right connection with the NVX units. ??

Going to go for easy low hanging fruit since with CH that's usually the case.? Since you can make the route with the web UI that leads me to believe that the route is not completely defined in CH.? If you go to the routing tab and the room that is not working if you click on the HDMI out of the D30 is the displays HDMI input shown on the right?? If not then CH does not know where to send the video after the D30 and the route won't happen.? Just click on the D30 output and select the input of the target display.

Hope this helps.? -Jim

Jim Felderman

President

ControlWorks Consulting, LLC

Crestron Services Provider

Unfortunately im controlling faders, mutes, and aux levels so i was looking for something that included level feedback since the end user will be using our touch panels for control through the crestron to the mixer and an iPad for direct control of the mixer. Thanks for the strings though Steve.

开云体育

Does anyone have a module for this? I could really use it. Thanks in advance.

This is a related problem, but not the same... however I think this solution may work for 4 series too. In a 3-series I have the same "Link Lost" problem with the communication with a HomeworksQS system. We install this kind of configuration in almost all of our projects and never happened to us before. What other behaviours I notice are:

1. After uploading program it works fine.
2. If I reboot the system, the Link Lost appears and the communication can't be reestablished until I upload program again.
3. If I connect to the CP3N just before the program starts, when it does the connection is successful and about the time some touch panels reports themselves in the console, I got the Link Lost.
4. We have a very similar problem with CP4N, but in that case, we can reboot the system and it works.
5. It works flawlessly in a 2-series.

So, the workaround I found is to wait 60s to establish the communication after the reboot. What I think is happening (at least in the 3-series) is that the system does some initial tasks with the TCP stack that breaks this older kind of connections, so the idea is to wait until everything is done and then connect the third party system. I use a simple delay in Simpl, between the signal that establish the communication and the TCP Client. Try that with your 4 series system, and let us know if it works.

clemare

The NVX and NAX streams are passing through the next work just fine. Extreme x440 G2 switch.? ? IGMP is doing what it should be doing. The problem is simply the D30 stream location won't change when changing the media source.? (basically switching from one E30s input to another E30's input).? I can go into the D30 gui and manual switch it, just can't get the processor to do it.?

开云体育

Hello all,

I am being asked to recommend the latest, best Google TV device for a client to Chromecast and operate apps similar to Apple TV but for Google ecosphere.

What should I tell to get and what has Ip control? I know Nvidia shield and Flirc works but has basic control.

@methdeathx where did you get with your project?

Thank you
Jon