¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. Crestron
  2. Messages
Expanded Topics Messages Polls
Date
Re: TSR-310 impressions

 

As a follow up.? I purchased a TSR-310 connected to Crestron Home.? I've been using it for about a week and it has performed really well.? It's running the latest firmware and connected to my 5ghz Ubiquiti Wifi 6 Pro access points.? I have not seen any significant lag when the remote has been sitting for hours and the battery life is pretty decent.

I also have HSR-310's but I definitely prefer the TSR-310.
Re: How to use a button with the sensor input on TPMC-4SMD

 

Thanks for the help! That was a perfect solution! I was looking for a single extender just for those sensors, and a name like Occupance_Sensor... Glad to know it is possible and people will point you in the right direction!?
Re: #cp3 #crestron #programming #simplwindows #cp3 #crestron #programming #simplwindows

 

I think the Cresnet port -IS- available on a 3-series processor in Slave mode.? Answer ID 5232 describes it, and I'm fairly certain I've done it before.
Re: Adagio AES

 

Trash the OOTB, unless you like the scrolling lists of doom.? I set up many of these just fine with a basic simpl program, a few idiosyncrasies to deal with, but solid if you don't ask them to do too much.? You can use the front buttons, but I almost always disabled them.? By the time all of your system builder software downloads and installs, I could already get a working simpl program up lol.
Re: #cp3 #crestron #programming #simplwindows #cp3 #crestron #programming #simplwindows

 

EISC for sure.? I'd put only my button presses and feedback to the CP3, and do any lighting logic local to the mc3. I'm not sure you can use an eslave device's gateway, I know you can't use it as a cresnet bridge.
Re: Communication Between programs

 

yep that was it. thank you!
Re: Communication Between programs

 

Try using 127.0.0.2 for both programs/slots.
Communication Between programs

 

I've done this before but its been a very long time. My understanding is you put and EIC in each program in the same IPID and set the ip address to 127.0.0.1 for slot 1 and 127.0.0.2 for slot 2. for some reason this isn't working, any know what i am missing ?
Re: S+ module not updating in parent program

 

Like Fabio said, definitely delete the SplWork folder.
Also, If you're running the program with local "Project" modules vs from your library, this also might account for not seeing the update if you hadn't used Recompile All...
Re: S+ module not updating in parent program

 

That does seem like a potential solution. Although, again, I verified that all the output files had current date stamps. But something wasn't getting triggered.

I now kinda hope I see this issue again so I can try it.?
Re: Samsung Terrace HDBT input

 

I am trying to find a IR Code for the HDBT Input.. Any Ideas anyone?
Re: S+ module not updating in parent program

 

Hi Terry,

Also try the "Recompile All" from within Simpl+ (located on the "Build" menu). Again, this is within SImpl+ and not SimplWindows.
For me, there have been occasions where a small modification made on a simpl+ module would not update into my simpl windows program until I did that.
Then also try the Recompile All on SimplWindows like others have recommended as well.
And deleting the SPIsWork folder would probably be a good idea just in case.?
With all these steps combined, things should work out.
Thanks,
Fabio
Re: #cp3 #crestron #programming #simplwindows #cp3 #crestron #programming #simplwindows

 

Your idea is the best, cresnet is about 38400 baus rate, super slow. You can also try the EISC but it will requiere having two running program and get things synchronized?
Re: #cp3 #crestron #programming #simplwindows #cp3 #crestron #programming #simplwindows

 

I would make the MC3 a slave.
That way all of the IOs including the EX gateway will be available in the CP3.
I am embarrassed to say that I am not sure about the cresnet. I would assume that would need to be moved over to the CP3.
I dont know how the cresnet port behaves when the MC3 is set to slave.?
#cp3 #crestron #programming #simplwindows #cp3 #crestron #programming #simplwindows

 
Edited

Hello,
? ? Here's my setup, I replaced a MC3 with a CP3N (RS-232 and the three IR functions have been moved over from the MC3)?but I also have a Crestron CLW-DIMEX-P controlled by the built-in MC3's RFGW-EX gateway to control the lights which aren't working now by Crestron.

1) How can I access the built-in gateway in the MC3 to control the lights?
2) How can I setup EISC correctly? (It didn't work for me, it looped the light control page on the panel.)
3) Can I use Cresnet?

Thank you for your future ideas.
Re: 1 beyond hawk camera

 

¿ªÔÆÌåÓý

Thanks Lincoln!

I had the same thought but without the product in front of me, I was not sure.

There is a camera module from Crestron in the database but it¡¯s for a single camera. Looks like I would need to modify the module to talk to two different camera IDs.

Also, the use case is in a council chambers with reinforced microphones. Seems to me that the reinforced mic audio would confuse the on-board mic array causing unintended consequences.

Thoughts?



On Feb 18, 2024, at 9:56?AM, Lincoln King-Cliby via groups.io <lincoln@...> wrote:

?
I have not used it but based on the description in the manual I think for manual control you'd probably want to recall the preset to force camera 1 (or camera 2) output and then only worry about controlling that head. It appears the addresses are fixed at 1 and 2 (\x81 and \x82) which make daisy chaining control problematic even though 485 control is supported... Obviously if doing VISCA over IP thats not really an issue?

Get
From: [email protected] <[email protected]> on behalf of James M Pedersen <jim@...>
Sent: Saturday, February 17, 2024 2:23:09 PM
To: [email protected] <[email protected]>
Subject: [crestron] 1 beyond hawk camera
?
Anyone use the two headed 1 beyond hawk camera?

If so, I am interested in how to managed the manual control. I assume you would address each camera head and control each with separate modules¡­.

Don¡¯t have one to test.

Any information would be appreciated





Re: 1 beyond hawk camera

 

¿ªÔÆÌåÓý

I have not used it but based on the description in the manual I think for manual control you'd probably want to recall the preset to force camera 1 (or camera 2) output and then only worry about controlling that head. It appears the addresses are fixed at 1 and 2 (\x81 and \x82) which make daisy chaining control problematic even though 485 control is supported... Obviously if doing VISCA over IP thats not really an issue?

Get

From: [email protected] <[email protected]> on behalf of James M Pedersen <jim@...>
Sent: Saturday, February 17, 2024 2:23:09 PM
To: [email protected] <[email protected]>
Subject: [crestron] 1 beyond hawk camera
?
Anyone use the two headed 1 beyond hawk camera?

If so, I am interested in how to managed the manual control. I assume you would address each camera head and control each with separate modules¡­.

Don¡¯t have one to test.

Any information would be appreciated





Re: S+ module not updating in parent program

 

I didn't try that. I didn't even think about it as never use it.

It *shouldn't* have made a difference as I know I was compiling the S+ module in question. But, I suppose it might have forced the main SIMPL program to relink to it in a way that wasn't happening. If it happens again, I will give that a shot.

I wonder how long it would take to recompile all of my S+ modules ... I might need a siesta while I wait. :)
1 beyond hawk camera

 

Anyone use the two headed 1 beyond hawk camera?

If so, I am interested in how to managed the manual control. I assume you would address each camera head and control each with separate modules¡­.

Don¡¯t have one to test.

Any information would be appreciated
Re: S+ module not updating in parent program

 

Did you use 'Recompile ALL' (Alt-F12) or Recompile all from the Project drop-down?

This is the only way that I compile programs now so I don't have to think about it...:)? ?(It might take a little longer but it saves my brain cells! Haha)
4261 - 4280 of 256472