开云体育

Interestingly enough, I have pretty much exactly the same scenario. We’ve had a CP3 working for numerous years without a day’s problem. Upgraded the same program to a CP4 and get the same results as you.

I’m interested in the fix with this - if there is any?

Hi All,
I'm working on a project with (3) Trane XL1050 WiFi TStats, attempting to use the 'TraneClimateLIB v1.0 Comm IP' Crestron module.
Has any one successfully done this (or alternative method)?
I have set the Tstats to reserved DHCP addresses via their Wifi interface matching this in their respective modules, and tried pairing but No Talkie...
The module help does not indicate any 'Vendor setup' other than the obvious IP addressing and the default port.
Of course we're trying to get a tech support number for Trane, but even if we do, I'm afraid I'll hear crickets from the staff on this subject.

Anyone have any experience with this??
TIA!

Would you be willing to share the IR file? The old yahoo links no longer work. I have a travel job I am not able to learn the remote. TIA!

This is a known issue with the RTSP video window, but I think MJPEG should work. I can't remember if putting the controls on a subpage helps, but that's worth a try.

Is there a way to overlay controls over the embedded video on an iPad. It works perfectly on a touch screen. When the video is active on the iPad the video covers the controls. My Z order is correct and the controls are set to be in front of the embedded video.

Also can someone confirm that “enhanced embedded video” is not compatible with the crestron app.?

?

I meant to say Thank you.

On Wed, May 19, 2021 at 06:16 PM, JPCH wrote:

You can have them behind the NVR or a separate switch, either is fine. If you are behind the NVR then you can add each camera individually by going through the NVR IP address with these streams (may be different depending on the model of NVR):

Snapshot URL: http://ipaddress/wps-cgi/jpg/image.cgi?camera=#&resolution=640x480&username=&password=

RTSP stream: rtsp://username:password@ipaddress:554/Streaming/Channels/101

Fill in the IP, username, and password accordingly. In the snapshot URL change "camera=#" for each camera. In the RTSP stream change "Channels/101" to "Channels/201" for camera 2, "Channels/301" for camera 3, etc. If you need to denote using the sub-stream rather than the main stream then do: "Channels/102", "Channels/202" and so on.

It has been a while since I've pointed towards Luma cameras that were not behind the NVR, but the last streams I used for that scenario were:
Snapshot URL: http://ipaddress/wps-cgi/jpg/image.cgi

RTSP Stream: rtsp://ipaddress/wps-cgi/video.cgi&resolution=1280x720

开云体育

Yes, Congratulations!

I finally got certified too at the beginning of the year and was able to attend Masters.
I wish I had been able to set the time aside back in 2005 when I managed to get to do the programming for cert course as it was called back then. Jon Ottesen predicted that I'd get the exam done on the plane trips home (New Zealand), but that was wishful thinking.
Yes the current exams are more difficult and often contain networking requirements that are unlikely to be real world, but I did learn a thing or two in the process. If you can allocate the hundreds of hours required (if you get fixated on something) it is worth the effort. In my case I programmed the solution in a rather complex way using poorly document Crestron methods, and then realised that an IP based approach was much simpler.

Getting to modern BIOS(UEFI) is a challenge even with directly attached keyboards. If your computer is Windows 10 based, holding the shift key while clicking on Restart button will give you the option to reatart and enter UEFI settings.

Congratulations. ?Tough job done.

Hi;

I have a complaint that the scrolling lists (dynamic button list) scroll too fast, and they would really like if I could slow them down a little. ?I can't seem to find any settings to change the scrolling sensitivity or velocity, and frankly it seems like the buttons in the list need to be held a bit in order to actually make a selection. ?I suppose this is just a 70 series feature, but if anybody knows how to make adjustments it would be great if you would share.

TIA

Kol

Great, now I know who to call when I need a food ordering system for my MPC ;)

I don't know if this will help, but some of the USB devices that I repair will change their USB identity or disconnect during booting or doing firmware upgrades.? That may be screwing up the NVX or the NVX is too slow to do the handshake when the computer boots.? You might try putting a USB hub between the computer and the NVX to maintain at least some type of connection to the NVX while the computer boots.? Or you might try using a 3rd party USB/Ethernet adapter instead and see if the works.

开云体育

I am working with a Lutron Quantum system for the first time. I am sending the phantom keypad commands via SIO but it is asking for (login:) from the RX$. I tried sending admin\x0D\x0A but that does not work. Not sur if anyone knows how to send the login information it is asking for but wanted to try. Any help would be appreciated.?

Thanks,
Rohan

We are using NVX with layer 2 switching with the computer USB running through NVX.? Everything seems to work fine except accessing the BIOS or boot options.? Currently, we have to move the keyboard directly into the computer's USB port to access these two options.? Has anybody encountered this or have a solution?
Thanks
Steven-The University of Alabama

"I can't help but think of our local volunteer FD that went on a run a couple of decades ago while the coffee machine was on only to return to a burned down fire station."
There's an irony there - just not quite seeing it :)
-s

Well it's broken again today and unfortunately Robert's trick didn't work today.
So unable to get to my open support cases
:(
-s