¿ªÔÆÌåÓý

Great thats what I though, I knew the RadioRA switches had a minimum load, so wasnt sure if the same applied to the EX switches (first time using them).

--- In Crestron@..., "seb_mtl" <seb514mtl@> wrote:

a switch is a switch

you can control a 120v coil relay who control another bigger relay.

you can control a power plant if you want


just , you need.... neutral ( the white one )





--- In Crestron@..., "jac777888" <jchelton@> wrote:

Hi,

I am trying to control a pool pump motor and notice the size limit for motors for the CLW-SWEX-P is 1/2 HP and pump is 1HP.

My question is has anyone used or forsee any problems using a CLW-SWEX-P to activate a contactor like a Fuji SC-E1 that has a 120V coil?

Thanks

a switch is a switch

you can control a 120v coil relay who control another bigger relay.

you can control a power plant if you want


just , you need.... neutral ( the white one )





--- In Crestron@..., "jac777888" <jchelton@> wrote:

Hi,

I am trying to control a pool pump motor and notice the size limit for motors for the CLW-SWEX-P is 1/2 HP and pump is 1HP.

My question is has anyone used or forsee any problems using a CLW-SWEX-P to activate a contactor like a Fuji SC-E1 that has a 120V coil?

Thanks

Hi,

I am trying to control a pool pump motor and notice the size limit for motors for the CLW-SWEX-P is 1/2 HP and pump is 1HP.

My question is has anyone used or forsee any problems using a CLW-SWEX-P to activate a contactor like a Fuji SC-E1 that has a 120V coil?

Thanks

Hi Matt,
beware of the fact that Crestron processor doesn?€?t handle the ?€?priority array?€? of BACnet IP protocol ; when the processor writes a BACnet object, it always does it with ?€?Priority 1?€? (probably highest than that used by the Honeywell control unit).

Alessandro

From: Neil Dorin
Sent: Thursday, December 13, 2012 2:41 PM
To: Crestron@...
Subject: Re: [Crestron] Bacnet Comms with Honeywell hawk centraline. S/w coach ax


BACnet uses UDP communication so there's no need to specify an IP address.

You'll need to have unique IDs assigned for the Crestron processor and the HVAC device you're talking to. It doesn't matter what ID you use as long as they're separate.

Probably the easiest way to handle HVAC control is to use an analog value to send to the HVAC system to request a set point, then the HVAC programmer supplies you with an analog input (input to his system) that will represent the current temp read by his sensor(s).

This way you only need 2 BACnet points per HVAC zone. Add the two for your processor as a device and his HVAC controller you're at 4 points for a single zone, plus 2 points for each additional. Under 50 points can be done with the free license in a 3-series processor.

-Neil Dorin

Sent from my iPhone

On 2012-12-13, at 1:31 AM, "mattstrads" <mailto:matt.stradling%40dawsonsav.co.uk> wrote:

Has anyone got any experience controlling this system over bacnet?
The hvac programmer hasn't done this before and needs to create backet points according to crestron. How can they do this?

Also in the crestron remote bacnet modules there seems to be nowhere to enter the remote IP address, only the name, id and port. Is this all the crestron needs? We did get some feedback about the remote device.

Any tips would be appreciated
Many thanks

Matt

Nessun virus nel messaggio.
Controllato da AVG - www.avg.com
Versione: 2013.0.2805 / Database dei virus: 2634/5953 - Data di rilascio: 12/12/2012

There's a standard one out there (CresDB I think) but be warned: Symetrix stuff is odd. Last time I did one it had a very strange characteristic. It only responded to serial commands via the 232 port if it was connected to a network via the LAN. Pull out the LAN cable and wham: "err&#92;x0D" to all commands. They said its a bug but a damn nasty one if you ask me. Ended up leaving my cheap 4 port switch in the back of it just to keep it working.

--- In Crestron@..., "raid shamsa" <raidshamsa@> wrote:

hi

does any one have a moduel to control a jupitor syries audio switcher from symetrics. will be willing to pay if need be

thanks

Does the flip-top TPS4 not have the option for sub-page z-order? I've always preferred the option for "Follow subpage-reference Z-order" for my projects, so I can always be sure of how the subpages will display. The C2N-FT-TPS4 doesn't have that Compile option, but the TPS4L does.

I can't recall if the option was there before and has disappeared or if I'm just thinking of other touchpanels that I've used.

Can someone confirm if this option was ever available for the ft-tps4?

I just updated everything with Master Installer last night, so I'm wondering if a recent update may have done away with it.

hi

does any one have a moduel to control a jupitor syries audio switcher from symetrics. will be willing to pay if need be

thanks

My favorite is the Vivitek projectors that will select any input via the
"RoomView Display" control module except for VGA. Nobody uses that anymore
anyway...


On Thu, Mar 21, 2013 at 3:25 PM, codinsorian <codinsorian@...> wrote:

I particularly enjoy the Epson projectors we purchased that is Roomview
compliant that does not work with....Roomview Enterprise.

Throughly enjoyed that one.

- Dan

--- In Crestron@..., Eric Walters <sentry07@> wrote:

Whyyyyyyyyyyyyyyyyyyyyyy why why why why would a manufacturer put

Roomview

stuff in their projectors and then turn off the web/roomview interface

when

you turn off the projector? Unless I'm being extremely stupid here, and

not

seeing the option to disable this, I don't get it. Turn the projector on
with the remote and the roomview stuff works, turn the projector off with
roomview and now none of the roomview stuff works and the projector won't
turn on.

WHY?! Tell me I'm not alone on this one, please.


[Non-text portions of this message have been removed]

------------------------------------




Check out the Files area for useful modules, documents, and drivers.

A contact list of Crestron dealers and programmers can be found in the
Database area.
Yahoo!
Groups Links

--
Jeremy Weatherford

My favorite is the Vivitek projectors that will select any input via the
"RoomView Display" control module except for VGA. Nobody uses that anymore
anyway...


On Thu, Mar 21, 2013 at 3:25 PM, codinsorian <codinsorian@...> wrote:

I particularly enjoy the Epson projectors we purchased that is Roomview
compliant that does not work with....Roomview Enterprise.

Throughly enjoyed that one.

- Dan

--- In Crestron@..., Eric Walters <sentry07@> wrote:

Whyyyyyyyyyyyyyyyyyyyyyy why why why why would a manufacturer put

Roomview

stuff in their projectors and then turn off the web/roomview interface

when

you turn off the projector? Unless I'm being extremely stupid here, and

not

seeing the option to disable this, I don't get it. Turn the projector on
with the remote and the roomview stuff works, turn the projector off with
roomview and now none of the roomview stuff works and the projector won't
turn on.

WHY?! Tell me I'm not alone on this one, please.


[Non-text portions of this message have been removed]

------------------------------------




Check out the Files area for useful modules, documents, and drivers.

A contact list of Crestron dealers and programmers can be found in the
Database area.
Yahoo!
Groups Links

--
Jeremy Weatherford

I particularly enjoy the Epson projectors we purchased that is Roomview
compliant that does not work with....Roomview Enterprise.

Throughly enjoyed that one.

- Dan

--- In Crestron@..., Eric Walters <sentry07@...> wrote:

Whyyyyyyyyyyyyyyyyyyyyyy why why why why would a manufacturer put

Roomview

stuff in their projectors and then turn off the web/roomview interface

when

you turn off the projector? Unless I'm being extremely stupid here, and

not

seeing the option to disable this, I don't get it. Turn the projector on
with the remote and the roomview stuff works, turn the projector off with
roomview and now none of the roomview stuff works and the projector won't
turn on.

WHY?! Tell me I'm not alone on this one, please.

------------------------------------




Check out the Files area for useful modules, documents, and drivers.

A contact list of Crestron dealers and programmers can be found in the
Database area.
Yahoo!
Groups Links

I particularly enjoy the Epson projectors we purchased that is Roomview compliant that does not work with....Roomview Enterprise.

Throughly enjoyed that one.

- Dan

--- In Crestron@..., Eric Walters <sentry07@> wrote:

Whyyyyyyyyyyyyyyyyyyyyyy why why why why would a manufacturer put Roomview
stuff in their projectors and then turn off the web/roomview interface when
you turn off the projector? Unless I'm being extremely stupid here, and not
seeing the option to disable this, I don't get it. Turn the projector on
with the remote and the roomview stuff works, turn the projector off with
roomview and now none of the roomview stuff works and the projector won't
turn on.

WHY?! Tell me I'm not alone on this one, please.


[Non-text portions of this message have been removed]

This would be a good way to do and make a hella TT to take care of the logic behind it.

JRW

--- In Crestron@..., Davis Whitehurst <whitehurstd@> wrote:

How about an analog inc for left/right that increments by 1 and analog inc for up/down that increments by 3. Run them into a sum. Add conditional logic for a wrap around effect. Obviously there would be a lot of buffers, ors and nors, but I think it could be done.

If value = 1.
Left sets it 9 for full wrap, or 3 if you just want to horizontal wrap
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 7 if you just want to vertical wrap
If value = 2.
Left goes to inrement
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 8 if you just want to vertical wrap

ETC...


Davis


________________________________

CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.


[Non-text portions of this message have been removed]

How about an analog inc for left/right that increments by 1 and analog inc for up/down that increments by 3. Run them into a sum. Add conditional logic for a wrap around effect. Obviously there would be a lot of buffers, ors and nors, but I think it could be done.

If value = 1.
Left sets it 9 for full wrap, or 3 if you just want to horizontal wrap
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 7 if you just want to vertical wrap
If value = 2.
Left goes to inrement
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 8 if you just want to vertical wrap

ETC...


Davis


________________________________

CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.


[Non-text portions of this message have been removed]

How about an analog inc for left/right that increments by 1 and analog inc for up/down that increments by 3. Run them into a sum. Add conditional logic for a wrap around effect. Obviously there would be a lot of buffers, ors and nors, but I think it could be done.

If value = 1.
Left sets it 9 for full wrap, or 3 if you just want to horizontal wrap
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 7 if you just want to vertical wrap
If value = 2.
Left goes to inrement
Right goes to increment
Down goes to increment
Up sets it 9 for full wrap, or 8 if you just want to vertical wrap

ETC...


Davis


________________________________

CONFIDENTIALITY NOTICE: This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. If you have received this transmission in error, please immediately destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.