开云体育

Even if you use another code set as a replacement, that won't help as Apple does not expose those *special* commands.
It is 3 commands in one - Short Press to select, P+H to get the item popup, keep P+H'ing to go to 'wiggle' mode.

The RMCLV will support this, just use the Crestron Apple TV 4K driver (or similar) and use Alex T's approach to managing the short and P+H functions.
This has been working great and will work fine with your set up.
One good thing about Crestron is long-term consistency with most programming methods

Install is New, CP4 on latest FW, TB and DBs are Latest or near-latest.
Check for updates is ON
File name is my standard for 6-8 years, no spaces.

As mentioned, I have not seen this issue before...

Just a quick question on this. I have to go to an ancient job tomorrow that has the select button problem. it is so old it has RMCLVs and two are controlling Apple TVs via IR.

Wondering if anyone has tried just learning in some different codes and whether that has worked. So rather than using the standards Apple TV codes, there's a place in the Apple TV settings menu where you can have it learn in new codes, from say, a Samsung remote and then just use Samsung codes in Crestron.

TIA

OP

On Tue, Dec 5, 2023 at 10:46 AM, @johnmax wrote:

mandated no blank spaces in the mobile project filename

The issue with spaces in the filename only affected TB versions prior to v3.07.144.
TB v3.07.144+ were fixed to surround the project filename with quotes.
This corrected the issue where CSPROJECTLOAD cmd wasn't receiving the full filename following "-P:".

Though, as a means of eliminating unnecessary/extraneous variables, True Blue Support will often request a basic alphanumeric filename be used during troubleshooting.

AV3>csprojectload ?
CSPROJECTLOAD { -P:Specific Project name? -T: WebXPanel | -T:MobileApp? -U:TB | -U:AU? ?}
? -P:? Load a specific project or? no parameter Show current installed projects?
? -T:? Project type 'WebXPanel' or 'MobileApp'. Optional for CH5Z projects to be loaded as both mobile app and xpanel project
? -U: the console command requestor ID, 'TB' - toolbox or 'AU' - Autoupdate?

Definitely make sure "iOS Settings > Crestron Go > Check for Update" is enabled whenever changes were made to the project files on the processor webserver. When this toggle is disabled, CGo will continue to load a locally cached version of the UI files rather than checking the small hash .xml file on the webserver to determine if the new .zip file rev should be downloaded to the iOS device. If you had CGo logging enabled at the time you experienced this, you should be able to see if the HTTPS connection was made and if the XML contents triggered the download of the new UI ZIP file.

As for Web Pages & Mobility Dialog populating with project information, that'll be dependent on whether the project was loaded prior to FW v1.601 (where Toolbox-generated PanelProjectInfo.ini metadata file resides in /html/ and is read by older versions of Toolbox/DBs), or after FW v1.601 (where CSPROJECTLOAD cmd generates the metadata that's read by newer versions of Toolbox/DBs).?

I feel like that Web and Mobility Projects dialog is not as useful depending on the firmware version of the processor. I think if its older (especially on 3 series) it doesnt show the projects with newer versions of toolbox. I think it started occuring around the time when they mandated no blank spaces in the mobile project filename. Sometimes the files show and sometimes they dont even if they are truly loaded there. Ive also had instances where I delete only one of the projects and they all show deleted then! I'll resort to File Manager to confirm whats actually there if I need to.?

Hah! I asked support some years ago why are there hidden console commands like these that they dont tell anyone about? I was told its so we dont get ourselves into trouble. Pretty ridiculous as i'm sure having many visible including this exact one would save them many support calls...

开云体育

C2N-CB-TS and a C2N-CBD-P-KP-ON-OFF, both running 1.003.0045

开云体育

CP4-R. Trying to add a couple new C2N-CBD keypads. Every time I add one, its network ID gets set to 01. I can change it in device tree viewer, and it says it's successful, but then resets back to 01 a couple minutes later. Cannot see the device in Crestron Home Setup. Latest firmware, can see serial/etc in Toolbox. Have tried four different units from two batches, same result. Any suggestions?

Hi All,
This just wasted some time tonite and wonder if others have seen it (I have faint memory of a thread but couldn't find it...)
I made a couple changes to the existing iPad and iPhone projects and as normal, went to the functions/Web-Mobility drop-down list in console, Deleted the projects then re-loaded with the updated versions.
I don't always delete but I did it this time.
Checked the iOS devices and they were still running the older version.
LSS, I had to create a Blank project with the same name as the iPad project, loaded it, then deleted and loaded the updated project.
Now the updates are visible...

Anyone else seen this, and is there a better way??? ?I can't say that I've seen this before, normally I can just load updates and it works immediately...

TIA!

Definite issues with HZ when coming from old CHV style.? Couple of learning curves and the propensity to fall offline, since there is no other option but WIFI.? Separate heat and cool temperature control, regardless if using Heat and Cool only vs auto.? The current temp and setpoint serial do not update regularly.? I wrote a module that takes the 3 digit analog feedback and converts it to 2 digits and rounds it up or down as needed.? Then convert it to serial text.

Nice, Thanks Tony!!

I used the module below with one of those recently, and it worked well.

/g/crestron/files/Modules/Lutron%20Grafik%20Eye%20QS%20Device%20%28mb%29.zip

On Mon, Dec 4, 2023 at 10:06 AM, @johnmax wrote:

wifisetup ?

Thanks JohnMAX, that's what I was looking for...
It'd be nice if the command was listed in the console help...:)

Hi All,
I have a take-over/upgrade project that has a couple older G-Eye units in the Media Room.
I've got a GRX-CI-NWK-E interface for them.?
Before I go and dig into this, does anyone have a Module already built for this integration that they would share?

TIA!

开云体育