开云体育

Hello, OMs Repeated everything according to the algorithm https://www.cantab.net/users/john.wiseman/Documents/picoBPQ.html I took the source code from here: https://github.com/g8bpq/picoBPQ I installed the driver from here, now the board is seen as a COM port. https://qna.habr.com/q/1010375 Trying to compile in ArduinoIDE gives the following error: C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\Users\CH\AppData\Local\arduino\sketches\1B43E9DB9ED8836EA5A21928A358E3B1\sketch\picoBPQ.ino.cpp.o: in function `_Z10LTEReadAllPcii': C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:693:(.text._Z10LTEReadAllPcii+0x50): undefined reference to `BPQFastPoll' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:706:(.text._Z10LTEReadAllPcii+0x7e): undefined reference to `BPQFastPoll' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\Users\CH\AppData\Local\arduino\sketches\1B43E9DB9ED8836EA5A21928A358E3B1\sketch\picoBPQ.ino.cpp.o: in function `_Z13FastPollDelayi': C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:722:(.text._Z13FastPollDelayi+0x22): undefined reference to `BPQFastPoll' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\Users\CH\AppData\Local\arduino\sketches\1B43E9DB9ED8836EA5A21928A358E3B1\sketch\picoBPQ.ino.cpp.o: in function `OutputDebugString': C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:881:(.text.OutputDebugString+0x50): undefined reference to `DEBUGLOG' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\Users\CH\AppData\Local\arduino\sketches\1B43E9DB9ED8836EA5A21928A358E3B1\sketch\picoBPQ.ino.cpp.o: in function `sendMQTTStatus.part.0': C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:346:(.text.sendMQTTStatus.part.0+0x1f8): undefined reference to `NODECALLLOPPED' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:346:(.text.sendMQTTStatus.part.0+0x200): undefined reference to `MQTT_PASS' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:346:(.text.sendMQTTStatus.part.0+0x204): undefined reference to `MQTT_PORT' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:346:(.text.sendMQTTStatus.part.0+0x208): undefined reference to `MQTT_USER' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:346:(.text.sendMQTTStatus.part.0+0x20c): undefined reference to `MQTT_HOST' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\Users\CH\AppData\Local\arduino\sketches\1B43E9DB9ED8836EA5A21928A358E3B1\sketch\picoBPQ.ino.cpp.o: in function `sendMQTTStatus': C:\RN1M\picoBPQ\picoBPQ-master\picoBPQ/picoBPQ.ino:346:(.text.sendMQTTStatus+0x1c): undefined reference to `MQTT_HOST' C:/Users/CH/AppData/Local/Arduino15/packages/rp2040/tools/pqt-gcc/4.0.1-8ec9d6f/bin/../lib/gcc/arm-none-eabi/14.2.0/../../../../arm-none-eabi/bin/ld.exe: C:\Users\CH\AppData\Local\arduino\sketches\1B43E9DB9ED8836EA5A21928A358E3B1\sketch\picoBPQ.ino.cpp.o: in function `sen

Hi All, My Static IP is unavailable at the moment so if you are using my Static IP to link with me then our link will be down. You can either wait till it comes back up which could be anytime between today and Tuesday next week or you could use ( zl2bau.co.nz ) my dynamic address and not have to worry about any issues with my Static IP address. I would be best for everyone to use zl2bau.co.nz which would be good if you have the time to change it. Many thanks. Regards ..... Peter ZL2BAU

I think it would be cool to use a propagation prediction engine like VOACAP to change HF connect options on the fly. I wonder how hard this would be to implement. I might take a look at the beta source to see how doable it is. Would anyone else be interested in BPQ32 having the capacity to choose the best QRG based on current predicted conditions instead of static tables? Might speed up scans to (maybe have BPQ32 skip dead bands in the scan). I am thinking a WP like bull could go out to keep indices fresh. -73 de Chris KQ6UP -- Thanks, Chris Maness

John, Seems that my HF ports are pretty well for now. But there is a new issue that I got with my VHF port running Direwolf: My BPQ node (YU7BPQ) communicated well with my home test node (YT7MPB-1) when I ran .065 version. When I upgraded to the .71 version, I noticed this strange behavior: 16:51:52T YU7BPQ>YT7MPB-1 Port=3 <XID C P> 2=21 3=22a486 RX Paclen=256 RX Window=7 16:51:57T YU7BPQ>YT7MPB-1 Port=3 <XID C P> 2=21 3=22a486 RX Paclen=256 RX Window=7 16:52:59T YU7BPQ>YT7MPB-1 Port=3 <XID C P> 2=21 3=22a486 RX Paclen=256 RX Window=7 16:53:05T YU7BPQ>YT7MPB-1 Port=3 <XID C P> 2=21 3=22a486 RX Paclen=256 RX Window=7 The above I see in the QtTerm window, every 5 second another line comes. The Direwolf itself was not changed. But it started showing this: [0L] YU7BPQ>YT7MPB-1:(XID cmd, p=1)XID error: Expected Balanced ABM to be set. XID error: Expected one of Half or Full Duplex be set. XID error: Expected Extended Address to be set. REJ modulo-8 I-Field-Length-Rx=256 Window-Size-Rx=7 [0L] YU7BPQ>YT7MPB-1:(XID cmd, p=1)XID error: Expected Balanced ABM to be set. XID error: Expected one of Half or Full Duplex be set. XID error: Expected Extended Address to be set. REJ modulo-8 I-Field-Length-Rx=256 Window-Size-Rx=7 ... etc etc ... My VHF port config is here: PORT PORTNUM=3 ; Port number ID=1200 Baud 144.875 MHz ; PORTS command text ;ID=1200 Baud 144.800 MHz ; PORTS command text TYPE=ASYNC ; RS232 connection IPADDR=127.0.0.1 ; DIREWOLF TCPPORT=8001 ; DIREWOLF SPEED=19200 CHANNEL=A ; TNC channel MAXFRAME=1 ; Max outstanding frames by VE1AMA (SK) Network105 founder ;MAXFRAME=3 ; Max outstanding frames ;FRACK=5000 ; Level 2 timeout (ms) FRACK=6000 ; Level 2 timeout (ms) by VE1AMA (SK) test Dec 30, 2021 ;RESPTIME=500 ; Level 2 delayed ACK (ms) RESPTIME=2000 ; Level 2 delayed ACK (ms) test Dec 19, 2020 RETRIES=10 ; Level 2 max retries ;PACLEN=236 ; Max packet length (bytes) PACLEN=128 ; Max packet length (bytes) by VE1AMA (SK) Network105 founder ;PACLEN=40 ; Max packet length (bytes) by UZ1HO "for FX25 in EU" ;TXDELAY=480 ; Transmit keyup delay (ms) TXDELAY=400 ; Transmit keyup delay (ms) ;TXDELAY=100 ; Transmit keyup delay (ms) SLOTTIME=100 ; CMSA interval timer (ms) TXTAIL=30 PERSIST=64 ; Persistence (256/(# transmissions-1) DIGIFLAG=0 ; Allow Digipeat on this port QUALITY=255 ; salje nodes listu ;QUALITY=0 ; nesalje nodes listu ;WL2KREPORT PUBLIC, www.winlink.org, 8778, CR6MPB, IN51GD, 00-23, 144875000, PKT1200, 10, 20, 5, 0 WL2KREPORT PUBLIC, www.winlink.org, 8778, YT7MPB-10, JN95WG, 00-23, 144875000, PKT1200, 10, 20, 5, 0 ;WL2KREPORT PUBLIC, www.winlink.org, 8778, II1CIT, JN44LJ, 00-23, 144800000, PKT1200, 10, 20, 5, 0 ENDPORT Any solution? Misko YT7MPB

Is there a way to monitor raw packets with LinBPQ like you can with BPQ32? I am running a TNC-X.

In my area IN1-1 and 2-1 are used. Is the below a correct implementation of this? TraceCalls=WIDE,TRACE FloodCalls=IN DigiCalls=W9JUN-10 ;ReplaceDigiCalls MaxTraceHops=2 MaxFloodHops=2 Couple examples: Digipeater IN2 audio level = 52(12/10) __|||____ [0.3] N9LYA-3>APBPQ1,N9LQP-2,IN2*:@290240z3844.42N/08628.33W_235/000g000t066r000P004p000h99b10190/MITWXN Mitchell IN N9LYA-3 KINMITCH1 Weather Station (linBPQ) Weather Report, WEATHER Station (blue), John G8BPQ Digipeater/IGate N 38 44.4200, W 086 28.3300 wind 0.0 mph, direction 235, gust 0, temperature 66, rain 0.00 in last hour, rain 0.04 since midnight, rain 0.00 in last 24 hours, humidity 99, barometer 30.09, "/MITWXN Mitchell IN N9LYA-3 KINMITCH1 Weather Station (linBPQ)" Digipeater IN2 audio level = 54(12/10) ____|____ [0.4] WB9TLH-11>APMI06,N9LQP-2,IN2*:@290242z3904.07N/08637.65W_109/000g000t061r000p026P026h54b10174Kirksville IN WX Digi Gate

Hi Gang! I am running my LinBPQ BBS on 145.050 out in Greenville Tx (~50 miles Northeast of DFW). I don't have any other packet stations near me. I can usually connect to N5COR-10 on 145.050 and I guess I could hear other stations if I changed frequency. I have a 3 element yagi that I am going to mount on the tower soon, so I am fairly sure I'll be able to reliably reach into the big city. My question is: how do I find a peer willing to accept and forward messages? Is there a way to reach out to the sysop that I don't know about? I'm sure once I find my forwarder I'll have more questions, is there a "setting up HA forwarding for dummies" document somewhere? Thanks and 73 Ken AC0TG

Good day Looking for an IN station to exchange udp mapping. DonP

John, I just upgraded linbpq from version 6.0.24.65 to version 6.0.24.71 and noticed an error (see the Subject): Initialising Port 01 Telnet Server Initialising Port 02 SCS Pactor /dev/ttyUSB1 Initialising Port 03 TCPKISS IP 127.0.0.1 Port 8001 Chan A Initialising Port 04 Bad config record RADIO=1 UZ7HO Host 127.0.0.1 Port 8000 Chan A Initialising Port 05 Bad config record RADIO=1 UZ7HO Host 127.0.0.1 Port 8000 Chan B Initialising Port 06 KAM Pactor /dev/ttyUSB3 That did not appear in version 6.0.24.65: Initialising Port 01 Telnet Server Initialising Port 02 SCS Pactor /dev/ttyUSB1 Initialising Port 03 TCPKISS IP 127.0.0.1 Port 8001 Chan A Initialising Port 04 UZ7HO Host 127.0.0.1 Port 8000 Chan A Initialising Port 05 UZ7HO Host 127.0.0.1 Port 8000 Chan B Initialising Port 06 KAM Pactor /dev/ttyUSB3 Misko YT7MPB

Hi John, for automated messages I am using the import successfully for bulletins and personal messages within the bbs for the equivalent file. Trying to send a winlink-mail or smtp-address in this way the domain is stripped an d causes an error-notification by the receiving system. That's how the import-file looks like: SP rms:usermail @ doma.in < MYCALL@... Subject-Text Lorem ipsum... /EX Same problem with "smtp:" instead of "rms:" and "winlink.org" instead of "doma.in" Thanks once again for your steady work and updates! 73 - Jochen

Hi attached is my current config for axip on my raspberrypi. just wondering what i am missing i am getting a bind error for the udp port. PORT PORTNUM=4 ID=AX/IP/UDP DRIVER=BPQAXIP PROTOCOL=AXUDP QUALITY=200 ; Quality factor applied to node broadcasts heard on ; this port, unless overridden by a locked route ; entry. Setting to 0 stops node broadcasts MINQUAL=0 ; Entries in the nodes table with qualities greater or ; equal to MINQUAL will be sent on this port. A value ; of 0 sends everything. MAXFRAME=7 ; Max outstanding frames (1 thru 7) FRACK=7000 ; Level 2 timout in milliseconds RESPTIME=1000 ; Level 2 delayed ack timer in milliseconds RETRIES=10 ; Level 2 maximum retry value UNPROTO=ID ; BTEXT broadcast addrs format: DEST[,digi1[,digi2]] CONFIG UDP 10093 ;Listens for UDP packets on this UDP port number UDP 10092 MHEARD ON ; AUTOADDMAP BROADCAST NODES BROADCAST ID MAP K0ZCO-1 K0ZCO.DDNS.NET UDP 10093 B ENDPORT -- Bob va3rjs

What would cause a Linchat to not report to the nodemap? Would an old 6.0.21.1 version not report due to being so outdated? Configuration looks correct, the links show yellow on the map, but the chat node does not. Of course the chat node shows Not Reporting in the Chat Report as well. (Asking for a friend.) Update is not yet possible...but in the future. -- 73, Mark, N5MDT Montgomery, Texas http://n5mdt.ham-radio-op.net:52852

Getting close to having this thing homed in - Anyone with advice, would love to hear it ;APRSPath 1= ; Receive only port ;APRSPath 7=APRS,WIDE1-1 ; Dest and up to 8 digis APRSPath 3=APRS,WIDE1-1,WIDE2-1 ;APRSPath 3=APRS,IN1-1 BeaconInterval=15 BeacontoIS=1 ; Send Beacon every 30 minute. Minimum is 5 mins ;MobileBeaconInterval=2 ; Beacon interval when moving MaxAge=60 TraceCalls=WIDE,TRACE ; Calls for CALLN-n Processing with Trace FloodCalls=IN ; Calls for CALLN-n Processing without Trace DigiCalls=W9JUN-10 ; Calls for Normal (ie no SSID manipulation) Digi ; For a Local "Fillin" Digi, you could include WIDE1-1 and leave out TraceCalls and FloodCalls ;ReplaceDigiCalls ; Replace DigiCalls with APRSCall. Omit if you want the call to be left as it is received. MaxTraceHops=2 ; Max value of n in CALLN-n processing. If a packet is received with n greater than MaxFloodHops=2 --------------------------- PORT PORTNUM=3 ID=APRS 144.390 MHz TYPE=ASYNC PROTOCOL=KISS IPADDR=127.0.0.1 TCPPORT=8001 ;QUALITY=0 ;MINQUAL=95 BCALL=W9JUN UNPROTO=APBPQ1 DIGIFLAG=0 CHANNEL=A MAXFRAME=2 FULLDUP=0 FRACK=8000 RESPTIME=1500 ;RETRIES=4 PACLEN=120 TXDELAY=300 TXTAIL=30 PERSIST=64 SLOTTIME=100 ENDPORT

Aloha, I’m looking for a few more testers to help field test Packet Commander, a new iOS app I’ve been developing. It’s a terminal for AX.25 packet radio, built specifically for iPhone and iPad. So far, it’s been in closed beta with a small group of operators and has received great feedback. You can learn more about the app here: https://packetcommander.com I’d like to expand testing across a broader range of setups. Currently, most testers are using BTECH UV-PRO HTs to connect to node running linbpq. I’m hoping to gain more coverage across different TNCs and node types. (Yes, I realize this is a BPQ mailing list, but it’s one of the most active packet communities I’ve found, and I’m hoping to reach folks with deep experience and access to a variety of AX.25 node platforms. My knowledge in that regard is still developing, and I literally live on an island with zero packet activity.) If you’re interested and meet the following criteria: ? You have an iPhone or iPad running iOS 18.2 or later ? You regularly connect to AX.25 nodes on VHF/UHF ? You use a TNC that works with iOS (see the supported list at the link above) ? You’re familiar with TestFlight ? You’re willing to provide thoughtful feedback and bug reports Please reach out directly with the configuration you’d like to test. Thanks and 73, Georges WH6AZ

Hi John (G8BPQ), I hope you have read my message of a couple of days ago to the list that outgoing IPv6 telnet forwarding doesn't work in the latest beta as well as the stable version. It fails to connect if I test it manually to a IPv6 only accessible tcp port. This makes that I can't forward to telnet servers who are only accessible over IPv6 or that IPv4/IPv6 accessible ports fall back to IPv4. They can access BPQ here with IPv6 over telnet, so luckily the mail flows with reserve forwarding in that way. Is there any solution to this? Regards, Boudewijn VE3TOK --- The issue with BPQ seems to be not the 'defaulting to IPv4' but that outgoing telnet to IPv6 fails to connect at all both in the latest stable and beta versions and this while IPv4 and IPv6 are both enabled for the telnet port, see below. -- I tested outgoing telnet from the BPQ node to a tcp port what can only handle IPv6 as I have a 6tunnel for IPv6 to Xnet, what is a IPv4 only program. 6tunnel converts here a IPv6 input at tcp port 24 to IPv4 at tcp port 23 what connects to Xnet. BPQ po BPQTOK:VE3TOK-12} Ports 1 Kiss Link to Kernel 2 Kiss Link to (X)net 3 Telnet Server 4 AX/IP/UDP attach 3 BPQTOK:VE3TOK-12} Ok c linux.ve3mch.ampr.org 24 *** Failed to Connect linux.ve3mch.ampr.org resolves both to an IPv4 and IPV6 address. I tested this from the latest stable BPQ version as well as from the latest beta version and both are failing with outgoing telnet over IPv6. Both IPv4 and IPv6 are enabled for the telnet port in BPQ with, IPV6=1 IPV4=1 From the linux shell to proof that IPv6 really works at port 24 # telnet linux.ve3mch.ampr.org 24 Trying 2001:470:1d:138::1... Connected to linux.ve3mch.ampr.org. Escape character is '^]'. (X)NET 1.39 @ VE3MCH-8 on LINUX: PSE enter Your callsign to login. Login: With IPv4 from the shell to Xnet at port 24 telnet -4 linux.ve3mch.ampr.org 24 Trying 44.135.85.151... telnet: Unable to connect to remote host: Connection refused What is as expected. Regards, Boudewijn VE3TOK -- There is nothing permanent except change Heraclitus

Good evening Enjoying trying to get linbpq setup for aprs - Currently the only path I see on aprs.fi is tcpip. However, if I run Direwolf alone, I get an RF path frequently. I have digimap setup, and the aprs path is wide2-1, as well.

John, I just noticed an unexpected restart for the #USWST chat hub. There are no RF ports on this system. The only 2 ports are AXIP and Telnet. It is a Debian Bookworm 12.10 x64 based vpn updated just a few days ago. The following is from the console. The first 3 lines are from my wrapper script but note the time is in PDT so for the moment is -7 hrs from UTC... also note that the executable was stripped after compile so I am guessing what follows may not be much help. I will rerun a non-stripped copy and if necessary via gdb if needed. ** * LinBPQ restart - 20250518200601 ** G8BPQ AX25 Packet Switch System Version 6.0.24.71 April 2025 Copyright 2001-2025 John Wiseman G8BPQ Current Directory is /home/linbpq/linbpq Log Directory is /home/linbpq/linbpq Making Directory /home/linbpq/linbpq/logs Configuration file Preprocessor. Using Configuration file /home/linbpq/linbpq/bpq32.cfg Conversion (probably) successful PORTS 0x55f9b7982e60 LINKS 0x55f9b7984ea0 DESTS 0x55f9b798aea0 ROUTES 0x55f9b7993b40 L4 0x55f9b7995940 BUFFERS 0x55f9b799e980 Initialising Port 01 AXIP Initialising Port 02 Telnet Server MQTT Enabled 0 Starting Chat Config File is /home/linbpq/linbpq/chatconfig.cfg Chat Started slave device: /dev/pts/0. symlink to /tmp/bpqtnc2 created TNC Emulator Init Complete SIGSEGV Received ./linbpq(+0x13b28c)[0x55f9b785628c] /lib/x86_64-linux-gnu/libc.so.6(+0x3c050)[0x7ffaa225b050] /lib/x86_64-linux-gnu/libc.so.6(+0xa9d76)[0x7ffaa22c8d76] /lib/x86_64-linux-gnu/libc.so.6(+0x5e258)[0x7ffaa227d258] /lib/x86_64-linux-gnu/libc.so.6(+0x7e758)[0x7ffaa229d758] ./linbpq(+0x1a15ee)[0x55f9b78bc5ee] ./linbpq(+0x1a5861)[0x55f9b78c0861] ./linbpq(+0x1a58ae)[0x55f9b78c08ae] ./linbpq(+0x1a6029)[0x55f9b78c1029] ./linbpq(+0x1a9754)[0x55f9b78c4754] SIGSEGV Received ./linbpq(+0x13b28c)[0x55f9b785628c] /lib/x86_64-linux-gnu/libc.so.6(+0x3c050)[0x7ffaa225b050] /lib/x86_64-linux-gnu/libc.so.6(+0xa9d76)[0x7ffaa22c8d76] /lib/x86_64-linux-gnu/libc.so.6(+0x5e258)[0x7ffaa227d258] /lib/x86_64-linux-gnu/libc.so.6(+0x7e758)[0x7ffaa229d758] ./linbpq(+0x1a15ee)[0x55f9b78bc5ee] ./linbpq(+0x1a5861)[0x55f9b78c0861] ./linbpq(+0x1a58ae)[0x55f9b78c08ae] ./linbpq(+0x1a6029)[0x55f9b78c1029] ./linbpq(+0x1a9754)[0x55f9b78c4754] Tnx es 73 de Rich WA3WLH

Good evening I am using Direwolf with linbpq as an APRS setup. However, not seeing the inet stream in direwolf, nor are stations populating on the aprs map from the bpq server. Here's what I have - ISHost=rotate.aprs2.net ; APRS-IS Host Name. May be either an IPV4 or an IPV6 Host ISPort=14580 ; Normal port for a filtered feed ISPasscode=8334 ; If you don't already have a passcode I can issue you one. ; ; You can specify a filter command to be sent when you log on to APRS-IS. Normally you don't ; need one. The APRS Mapping Application (BPQAPRS) sets a filter when it starts, ; and if you aren't running an APRS application, there isn't much point in getting info from APRS-IS ; ISFilter=m/64 ;GateLocalDistance=0 ;GATEDPATH 3=APRS LOGAPRSIS=1

Looking to add a UHF port to our LinBPOQ site. Any recommendations, either for or against, for a used radio? Running a Kenwood TM-271 for VHF. Dave Menges