Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

Hi Glenn,

Thanks for the assistance. So AGW does show connected in the right corner but the Connect tab on the top is greyed our.

But I have an update. I tried Kiss and it works okay now.

Another but. When I connect with KC3SMW-7 via W3SK I connect but immediately send a DM with KC3SMW-7 continuing to send me the welcome instructions.

Ah, it's nice to have local tech support :-) Good talking to you on the repeater Glenn. So I'm going to try adding -1 to my call and maybe changing the local port in case of conflicts to see if that helps with the connect to KC3SMW-7.

Thanks again Glenn and don't work too hard today.

73, Ron NY3J

On 5/25/23 06:17, N3MEL - Glenn wrote:

Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

So I tried adding -1 to my call without success. Also tried changing the Kiss port to 8010 without success. Below is the monitor window when I connect to KC3SMW-7. You can see where I send the immediate DM.

I'm in the process of trying Linpac to see if that connects.

10:58:38T NY3J-1>KC3SMW-7,W3SK <SABM C P>
10:58:41R NY3J-1>KC3SMW-7,W3SK* <SABM C P>
10:58:45R KC3SMW-7>NY3J-1,W3SK* <UA R F>
10:58:45T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:46T NY3J-1>KC3SMW-7,W3SK <SABM C P>
10:58:46R KC3SMW-7>NY3J-1,W3SK* <I C P R0 S0>
Welcome to the chengmanian Node.? A Bucks County Node available to all amateur operators.
BBS CHAT RMS CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD
Type ? for list of available commands.
10:58:46T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:50R NY3J-1>KC3SMW-7,W3SK* <DM R F>
10:58:50R NY3J-1>KC3SMW-7,W3SK* <SABM C P>
10:58:50R NY3J-1>KC3SMW-7,W3SK* <DM R F>
10:58:54R KC3SMW-7>NY3J-1,W3SK* <UA R F>
10:58:54T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:54T NY3J-1>KC3SMW-7,W3SK <SABM C P>
10:58:55R KC3SMW-7>NY3J-1,W3SK* <I C P R0 S0>
Welcome to the chengmanian Node.? A Bucks County Node available to all amateur operators.
BBS CHAT RMS CONNECT BYE INFO NODES PORTS ROUTES USERS MHEARD
Type ? for list of available commands.
10:58:55T NY3J-1>KC3SMW-7,W3SK <DM R F>
10:58:56T NY3J-1>KC3SMW-7,W3SK <DISC C P>

73, Ron NY3J

On 5/25/23 06:52, Ron NY3J via groups.io wrote:

Hi Glenn,

Thanks for the assistance. So AGW does show connected in the right corner but the Connect tab on the top is greyed our.

But I have an update. I tried Kiss and it works okay now.

Another but. When I connect with KC3SMW-7 via W3SK I connect but immediately send a DM with KC3SMW-7 continuing to send me the welcome instructions.

Ah, it's nice to have local tech support :-) Good talking to you on the repeater Glenn. So I'm going to try adding -1 to my call and maybe changing the local port in case of conflicts to see if that helps with the connect to KC3SMW-7.

Thanks again Glenn and don't work too hard today.

73, Ron NY3J

On 5/25/23 06:17, N3MEL - Glenn wrote:

Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

Hi Glenn,

Thanks for the assistance. So AGW does show connected in the right corner but the Connect tab on the top is greyed our.

But I have an update. I tried Kiss and it works okay now.

Another but. When I connect with KC3SMW-7 via W3SK I connect but immediately send a DM with KC3SMW-7 continuing to send me the welcome instructions.

Ah, it's nice to have local tech support :-) Good talking to you on the repeater Glenn. So I'm going to try adding -1 to my call and maybe changing the local port in case of conflicts to see if that helps with the connect to KC3SMW-7.

Thanks again Glenn and don't work too hard today.

73, Ron NY3J

On 5/25/23 06:17, N3MEL - Glenn wrote:

Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

Which version of QtTerm are you running?

Until recently there was a bug where if you ran it in single window mode with a combined terminal and monitor screen with AGW enabled the AGW monitor session would grab the whole window and connect was greyed out. Fixes are to upgrade or run in multi window (MDI or Tabbed) mode.

73,
John

On 25/05/2023 11:52, Ron NY3J via groups.io wrote:

Hi Glenn,

Thanks for the assistance. So AGW does show connected in the right corner but the Connect tab on the top is greyed our.

But I have an update. I tried Kiss and it works okay now.

Another but. When I connect with KC3SMW-7 via W3SK I connect but immediately send a DM with KC3SMW-7 continuing to send me the welcome instructions.

Ah, it's nice to have local tech support :-) Good talking to you on the repeater Glenn. So I'm going to try adding -1 to my call and maybe changing the local port in case of conflicts to see if that helps with the connect to KC3SMW-7.

Thanks again Glenn and don't work too hard today.

73, Ron NY3J

On 5/25/23 06:17, N3MEL - Glenn wrote:

Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

Hi John,

It's QtTermTCP Version 0.0.0.60 64 bit version. I couldn't find anything newer.

Ron NY3J

On 5/25/23 08:53, John G8BPQ wrote:

Which version of QtTerm are you running?

Until recently there was a bug where if you ran it in single window mode with a combined terminal and monitor screen with AGW enabled the AGW monitor session would grab the whole window and connect was greyed out. Fixes are to upgrade or run in multi window (MDI or Tabbed) mode.

73,
John

On 25/05/2023 11:52, Ron NY3J via groups.io wrote:

Hi Glenn,

Thanks for the assistance. So AGW does show connected in the right corner but the Connect tab on the top is greyed our.

But I have an update. I tried Kiss and it works okay now.

Another but. When I connect with KC3SMW-7 via W3SK I connect but immediately send a DM with KC3SMW-7 continuing to send me the welcome instructions.

Ah, it's nice to have local tech support :-) Good talking to you on the repeater Glenn. So I'm going to try adding -1 to my call and maybe changing the local port in case of conflicts to see if that helps with the connect to KC3SMW-7.

Thanks again Glenn and don't work too hard today.

73, Ron NY3J

On 5/25/23 06:17, N3MEL - Glenn wrote:

Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

Latest is 0.65. I've uploaded an Intel 64 bit build to my beta area,

73,
John

On 25/05/2023 13:59, Ron NY3J via groups.io wrote:

Hi John,

It's QtTermTCP Version 0.0.0.60 64 bit version. I couldn't find anything newer.

Ron NY3J

On 5/25/23 08:53, John G8BPQ wrote:

Which version of QtTerm are you running?

Until recently there was a bug where if you ran it in single window mode with a combined terminal and monitor screen with AGW enabled the AGW monitor session would grab the whole window and connect was greyed out. Fixes are to upgrade or run in multi window (MDI or Tabbed) mode.

73,
John

On 25/05/2023 11:52, Ron NY3J via groups.io wrote:

Hi Glenn,

Thanks for the assistance. So AGW does show connected in the right corner but the Connect tab on the top is greyed our.

But I have an update. I tried Kiss and it works okay now.

Another but. When I connect with KC3SMW-7 via W3SK I connect but immediately send a DM with KC3SMW-7 continuing to send me the welcome instructions.

Ah, it's nice to have local tech support :-) Good talking to you on the repeater Glenn. So I'm going to try adding -1 to my call and maybe changing the local port in case of conflicts to see if that helps with the connect to KC3SMW-7.

Thanks again Glenn and don't work too hard today.

73, Ron NY3J

On 5/25/23 06:17, N3MEL - Glenn wrote:

Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

On Thu, May 25, 2023 at 12:25 PM, Ron NY3J wrote:

Thanks John,

I installed qmake6. Then downloaded the QtTermSource.zip from your site. I extracted then ran qmake6 and got this error:

ny3j@ny3j-Studio-XPS-435T-9000:~/Downloads/QtTermSource$ sudo qmake6
[sudo] password for ny3j:??????? ?
Project ERROR: Unknown module(s) in QT: core gui network widgets
ny3j@ny3j-Studio-XPS-435T-9000:~/Downloads/QtTermSource$

Ron NY3J

On 5/25/23 09:42, John G8BPQ wrote:

Latest is 0.65. I've uploaded an Intel 64 bit build to my beta area,

73,
John

On 25/05/2023 13:59, Ron NY3J via groups.io wrote:

Hi John,

It's QtTermTCP Version 0.0.0.60 64 bit version. I couldn't find anything newer.

Ron NY3J

On 5/25/23 08:53, John G8BPQ wrote:

Which version of QtTerm are you running?

Until recently there was a bug where if you ran it in single window mode with a combined terminal and monitor screen with AGW enabled the AGW monitor session would grab the whole window and connect was greyed out. Fixes are to upgrade or run in multi window (MDI or Tabbed) mode.

73,
John

On 25/05/2023 11:52, Ron NY3J via groups.io wrote:

Hi Glenn,

Thanks for the assistance. So AGW does show connected in the right corner but the Connect tab on the top is greyed our.

But I have an update. I tried Kiss and it works okay now.

Another but. When I connect with KC3SMW-7 via W3SK I connect but immediately send a DM with KC3SMW-7 continuing to send me the welcome instructions.

Ah, it's nice to have local tech support :-) Good talking to you on the repeater Glenn. So I'm going to try adding -1 to my call and maybe changing the local port in case of conflicts to see if that helps with the connect to KC3SMW-7.

Thanks again Glenn and don't work too hard today.

73, Ron NY3J

On 5/25/23 06:17, N3MEL - Glenn wrote:

Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

Great my mail got sent before I finished it.?



This is the binary John is referring to Ron

You don’t need to build from source, and the source zip is not up to date, its usually managed in John subversion repo.

73
Red

Thanks John,

I installed qmake6. Then downloaded the QtTermSource.zip from your site. I extracted then ran qmake6 and got this error:

ny3j@ny3j-Studio-XPS-435T-9000:~/Downloads/QtTermSource$ sudo qmake6
[sudo] password for ny3j:??????? ?
Project ERROR: Unknown module(s) in QT: core gui network widgets
ny3j@ny3j-Studio-XPS-435T-9000:~/Downloads/QtTermSource$

Ron NY3J

On 5/25/23 09:42, John G8BPQ wrote:

Latest is 0.65. I've uploaded an Intel 64 bit build to my beta area,

73,
John

On 25/05/2023 13:59, Ron NY3J via groups.io wrote:

Hi John,

It's QtTermTCP Version 0.0.0.60 64 bit version. I couldn't find anything newer.

Ron NY3J

On 5/25/23 08:53, John G8BPQ wrote:

Which version of QtTerm are you running?

Until recently there was a bug where if you ran it in single window mode with a combined terminal and monitor screen with AGW enabled the AGW monitor session would grab the whole window and connect was greyed out. Fixes are to upgrade or run in multi window (MDI or Tabbed) mode.

73,
John

On 25/05/2023 11:52, Ron NY3J via groups.io wrote:

Hi Glenn,

Thanks for the assistance. So AGW does show connected in the right corner but the Connect tab on the top is greyed our.

But I have an update. I tried Kiss and it works okay now.

Another but. When I connect with KC3SMW-7 via W3SK I connect but immediately send a DM with KC3SMW-7 continuing to send me the welcome instructions.

Ah, it's nice to have local tech support :-) Good talking to you on the repeater Glenn. So I'm going to try adding -1 to my call and maybe changing the local port in case of conflicts to see if that helps with the connect to KC3SMW-7.

Thanks again Glenn and don't work too hard today.

73, Ron NY3J

On 5/25/23 06:17, N3MEL - Glenn wrote:

Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

It looks like you've installed qmake but not the rest of the Qt package.

I've not tried Qt 6 yet, but for Qt 5 I've found that installing libqt5serialport5-dev will drag in everything else that is needed.

73,
John

On 25/05/2023 20:25, Ron NY3J via groups.io wrote:

Thanks John,

I installed qmake6. Then downloaded the QtTermSource.zip from your site. I extracted then ran qmake6 and got this error:

ny3j@ny3j-Studio-XPS-435T-9000:~/Downloads/QtTermSource$ sudo qmake6
[sudo] password for ny3j:??????? ?
Project ERROR: Unknown module(s) in QT: core gui network widgets
ny3j@ny3j-Studio-XPS-435T-9000:~/Downloads/QtTermSource$

Ron NY3J

On 5/25/23 09:42, John G8BPQ wrote:

Latest is 0.65. I've uploaded an Intel 64 bit build to my beta area,

73,
John

On 25/05/2023 13:59, Ron NY3J via groups.io wrote:

Hi John,

It's QtTermTCP Version 0.0.0.60 64 bit version. I couldn't find anything newer.

Ron NY3J

On 5/25/23 08:53, John G8BPQ wrote:

Which version of QtTerm are you running?

Until recently there was a bug where if you ran it in single window mode with a combined terminal and monitor screen with AGW enabled the AGW monitor session would grab the whole window and connect was greyed out. Fixes are to upgrade or run in multi window (MDI or Tabbed) mode.

73,
John

On 25/05/2023 11:52, Ron NY3J via groups.io wrote:

Hi Glenn,

Thanks for the assistance. So AGW does show connected in the right corner but the Connect tab on the top is greyed our.

But I have an update. I tried Kiss and it works okay now.

Another but. When I connect with KC3SMW-7 via W3SK I connect but immediately send a DM with KC3SMW-7 continuing to send me the welcome instructions.

Ah, it's nice to have local tech support :-) Good talking to you on the repeater Glenn. So I'm going to try adding -1 to my call and maybe changing the local port in case of conflicts to see if that helps with the connect to KC3SMW-7.

Thanks again Glenn and don't work too hard today.

73, Ron NY3J

On 5/25/23 06:17, N3MEL - Glenn wrote:

Not sure what mean, Nothing Happens? AGW is showing
in the Connect tab? If it is in the lower right corner there a
box that should say AGW Connected or not.

I can meet you the CCAR repeater in about 10 minutes or tonight
after nets??

N3MEL

John and Red,

I found an executable on the beta site, QtTermTCP Version 0.0.0.65 and it seems to work okay. Thanks guys.

73, Ron NY3J