开云体育

Hum… I’m not showing up.. Mitchell Indiana.. What do I need to do to see me.. Very nice map! Sent: Monday, April 21, 2025 11:11 AM To: [email protected] Subject: Re: [bpq32] Node/BBS

https://nodes.ukpacketradio.network/packet-network-map.html

The BPQ node map has a tab called Modem Modes if you have not seen it.? Anyone with a Rigcontrol statement, or a Frequency statement will show the DIAL frequencies.? However, the call listed is the

Hi folks. Is there a map or list of BPQ nodes/BBS with operating frequencies? Many do not mention the frequencies on the node map. I would like to try connections on 10m. TIA

You were spot on, I removed the ";" comments and it started to work correctly. Thank You 73!

Heber, Does it work if you type at the node: `radio 5 14.103` You might try that and see, I suspect that the RIGCONTROL lines dont like ';' characters in the scan lists. I had similar issue with

Hello Trying to get the ICOM 7000 to work with Rigcontrol. PTT is working but can get to change frequencies. I have tried multiple variation of the below without success. Help would be

I think you'll have to decide if you want to do it on manual connects or not. You may have a default value defined in the config file too I believe if you want.

Hi, Can this be fixed so if your source address is in LOCALNET=x.x.x.x/24 on the telnet port also covers AGW connections to node "SWITCH"? Meaning that when I use QTTermTCP to connect to bpq in AGW

Sometime overnight the chat service #USWCH:WA3WLH-14 on the US West regional chat hub #USWST:WA3WLH-15 dropped the chat link with my home chat service WLHCHT:WA3WLH-11 on node WLHNOD:WA3WLH-7. This is

Good Morning Lee, Perfect I can understand that fully, Thank you... All the best from Alan

[email protected]> wrote: Hello Alan, There are two choices. 1) Connect to your node, and issue *S* (S is for stats) or 2) Connect to your BBS and issue *S*. Therefore you will either find it

Are you sure your service is called gb7esc? Do you need sudo? The S command shows node uptime. Make sure it goes back to zero when you try to restart. Hi John, No I never use sudo, i always su -

You need to add UNPROTO=BEACON (or whatever address you want your beacons to go to) in each PORT that you want to send beacons on. systemctl restart gb7esc.service Are you sure your service is

Thank you for the link will investigate, do I need it, NOPE but I have always enjoyed Packet I had a setup using lots of addons for AX25 using Ubuntu 14.04 On a Pentium 4 But the setup got out off

Hi John, Thanks for the reply, I am never sure of anything,? I can only tell you what I did :) You say that? ?BTEXT needs to be directed to a port, what is the command please... All the best

It isn't a very useful thing to do but it shouldn't crash. I'll look into it. 73, John

Are you sure that systemctl restart gb7esc.service worked and restarted BPQ? BTEXT is sent to the UNPROTO call specified in the PORT config, so if you don't have UNPROTO it won't set sent. 73,

Thank you. So now the above sample looks like this: IDLETIME 60 ATTACH 6 RADIO 14.10230 USB #\TRX F 14102.30 #\TRX F 7044 PAUSE 2 #MYLEVEL 1 MSGTYPES PTRB5000 C <call> ELSE PAUSE 30 IDLETIME

Can someone help with confirming or denying that this situation happens to you please. Required: Windows 10.? BPQ Mail.? HTTP access.? Templates installed. Open Browser to BPQ Node Pages Select